Article 133Appointment of an Operations Supervisor of Press Machines
As regards the work set forth in Article 6, item (vii) of the Order, the employer must appoint an operations supervisor of press machines from the persons who have completed the skill training course for operations supervisor of press machines.
事業者は、令第六条第七号の作業については、プレス機械作業主任者技能講習を修了した者のうちから、プレス機械作業主任者を選任しなければならない。
Article 134Duties of the Operations Supervisor of Press Machines
The employer must have the operations supervisor of press machines carry out the following matters:
事業者は、プレス機械作業主任者に、次の事項を行なわせなければならない。
to inspect the press machine and its safety device;
プレス機械及びその安全装置を点検すること。
to immediately take necessary measures when having found any abnormality in the press machine and its safety device;
プレス機械及びその安全装置に異常を認めたときは、直ちに必要な措置をとること。
To store the key when having equipped a press machine or its safety device with a changeover key switch; and
プレス機械及びその安全装置に切替えキースイツチを設けたときは、当該キーを保管すること。
to directly supervise the work of fitting, removing and adjusting a die.
金型の取付け、取りはずし及び調整の作業を直接指揮すること。
Article 134-2Storing the Key of a Changeover Key Switch
When work other than those set forth in Article 6, item (vii) of the Order among work using a power press are carried out, and a changeover key switch for the power press and its safety device have been provided, the employer must designate a person who stores the key switch, and have the person store the key.
Article 134-3Periodical Self-inspections
As regards a power press, the employer must carry out self-inspections for the following matters periodically once every period not exceeding a year; provided, however, that this does not apply to the non-use period of a power press which is not used for a period exceeding one year:
事業者は、動力プレスについては、一年以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一年を超える期間使用しない動力プレスの当該使用しない期間においては、この限りでない。
abnormalities in crankshafts, flywheels and other power transmission devices;
クランクシヤフト、フライホイールその他動力伝達装置の異常の有無
abnormalities in a clutch, a brake and other controlling systems;
クラツチ、ブレーキその他制御系統の異常の有無
abnormalities in an anti-repeat device, a quick-stop device or an emergency stop device;
一行程一停止機構、急停止機構及び非常停止装置の異常の有無
abnormalities in a slide, a connecting rod or other slide-related parts;
スライド、コネクチングロツドその他スライド関係の異常の有無
abnormalities in a magnet valve, a pressure control valve or other air pressure systems;
電磁弁、圧力調整弁その他空圧系統の異常の有無
abnormalities in a magnet valve, a hydraulic pump or other hydraulic systems;
電磁弁、油圧ポンプその他油圧系統の異常の有無
abnormalities in a limit switch, a relay or other electrical systems;
リミツトスイツチ、リレーその他電気系統の異常の有無
abnormalities in a die cushion and its accessories; and
ダイクツシヨン及びその附属機器の異常の有無
abnormalities in the mechanism for preventing dangers due to a slide.
スライドによる危険を防止するための機構の異常の有無
As regards the power press set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.
Article 135
As regards a power-driven shearing machine, the employer must carry out self-inspections for the following matters periodically once every period not exceeding a year; provided, however, that this does not apply to the non-use period of a power-driven shearing machine which is not used for a period exceeding one year:
事業者は、動力により駆動されるシヤーについては、一年以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一年を超える期間使用しないシヤーの当該使用しない期間においては、この限りでない。
abnormalities in a clutch and a brake;
クラツチ及びブレーキの異常の有無
abnormalities in a sliding mechanism;
スライド機構の異常の有無
abnormalities in an anti-repeat device, a quick-stop device, and an emergency stop device;
一行程一停止機構、急停止機構及び非常停止装置の異常の有無
abnormalities in a magnet valve, a pressure-reducing valve and a pressure gauge; and
電磁弁、減圧弁及び圧力計の異常の有無
abnormalities in wiring and switches.
配線及び開閉器の異常の有無
As regards the shearing machine set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.
Article 135-2Record of Periodical Self-inspections
When having carried out the self-inspections set forth in the preceding two Articles, the employer must record the following matters and preserve the records for three years:
事業者は、前二条の自主検査を行つたときは、次の事項を記録し、これを三年間保存しなければならない。
the date of the inspection;
検査年月日
the method of the inspection;
検査方法
the parts of a machine inspected;
検査箇所
the results of the inspection;
検査の結果
the name of the person who has carried out the inspection; and
検査を実施した者の氏名
when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.
検査の結果に基づいて補修等の措置を講じたときは、その内容
Article 135-3Specified Self-inspections
The self-inspection prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to a power press (hereinafter referred to as the "specified inspection") is to be the self-inspection prescribed in Article 134-3.
A person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to a power press is to be a person who falls under any of the following items:
a person who falls under any of the following sub-items and has completed the training course specified by the Minister of Health, Labour and Welfare:
次のいずれかに該当する者で、厚生労働大臣が定める研修を修了したもの
a person who has majored in and graduated from an engineering course of a university or a technical college under the School Education Act (including a person who has been conferred a bachelor's degree by the National Institution for Academic Degrees and Quality Enhancement of Higher Education (limited to one who majored in such a course), a person found to have equivalent or greater scholastic ability, and a person who majored in such a course and completed the first-stage course of a professional university; the same applies in Article 151-24, paragraph (2), item (i), (a)), and has experience of having been engaged in the work of inspection or maintenance of a power press for two years or longer, or design or manufacture of a power press for five years or longer;
学校教育法による大学又は高等専門学校において工学に関する学科を専攻して卒業した者(大学改革支援・学位授与機構により学士の学位を授与された者(当該学科を専攻した者に限る。)若しくはこれと同等以上の学力を有すると認められる者又は当該学科を専攻して専門職大学前期課程を修了した者を含む。第百五十一条の二十四第二項第一号イにおいて同じ。)で、動力プレスの点検若しくは整備の業務に二年以上従事し、又は動力プレスの設計若しくは工作の業務に五年以上従事した経験を有するもの
a person who has majored in and graduated from an engineering course of a senior high school or a secondary education school under the School Education Act and has experience of having been engaged in the work of inspection or maintenance of a power press for four years or longer, or design or manufacture of a power press for seven years or longer;
a person who has experience of having been engaged in the work of inspection or maintenance of a power press for seven years or longer, or design or manufacture of a power press for 10 years or longer; or
動力プレスの点検若しくは整備の業務に七年以上従事し、又は動力プレスの設計若しくは工作の業務に十年以上従事した経験を有する者
a person who has completed the skill training course for operations supervisor of press machine listed in the Appended Table 18, item (2) of the Act and who has experience of having been engaged in the work using a power press for 10 years or longer; or
other persons specified by the Minister of Health, Labour and Welfare.
その他厚生労働大臣が定める者
As regards the application of the provisions of the preceding Article when having a registered inspection agency set forth in Article 45, paragraph (2) of the Act (hereinafter referred to as the "registered inspection agency") conduct the specified inspection pertaining to a power press, the term "the name of the person who has carried out the inspection" in item (v) of the same Article is deemed to be replaced with "the name of the registered inspection agency."
When having carried out the specified inspection pertaining to a power press, the employer must affix an inspection sticker stating the month and year when the specified inspection was carried out at a readily visible part of the power press.
Article 136Inspection before Commencing the Work
When carrying out the work using press, etc., the employer must inspect the following matters before commencing the work for the day:
事業者は、プレス等を用いて作業を行うときには、その日の作業を開始する前に、次の事項について点検を行わなければならない。
the function of a clutch and a brake;
クラツチ及びブレーキの機能
the slackness of a bolt of a crankshaft, a flywheel, a slide, a connecting rod and a connecting screw;
クランクシヤフト、フライホイール、スライド、コネクチングロツド及びコネクチングスクリユーのボルトのゆるみの有無
the function of an anti-repeat device, quick-stop device and an emergency stop device;
一行程一停止機構、急停止機構及び非常停止装置の機能
the function of mechanism for preventing dangers due to a slide or a blade;
スライド又は刃物による危険を防止するための機構の機能
the conditions of a die and a bolster for a press machine; and
プレス機械にあつては、金型及びボルスターの状態
the conditions of a blade and a table for a shearing machine.
シヤーにあつては、刃物及びテーブルの状態
Article 137Repair of Press Machines
When having found any abnormality in carrying out the self-inspection set forth in Article 134-3 or Article 135, or the inspection set forth in the preceding Article, the employer must make repairs or take other necessary measures.
第五節 遠心機械
Section 5 Centrifugal Machine
Article 138Fitting of a Lid
The employer must provide a lid on a centrifugal machine.
事業者は、遠心機械には、ふたを設けなければならない。
Article 139Suspension of Operation in Taking Out the Contents
Article 140Prohibition of Use at Speeds Exceeding Maximum Allowable Rotation
As regards a centrifugal machine, the employer must not use the centrifugal machine at a speed exceeding its maximum allowable rotating speed.
事業者は、遠心機械については、その最高使用回転数をこえて使用してはならない。
Article 141Periodical Self-inspections
As regards a power-driven centrifugal machine, the employer must carry out self-inspections for the following matters periodically once every period not exceeding a year; provided, however, that this does not apply to the non-use period of a centrifugal machine which is not used for a period exceeding one year:
事業者は、動力により駆動される遠心機械については、一年以内ごとに一回、定期に、次の事項について自主検査を行なわなければならない。ただし、一年をこえる期間使用しない遠心機械の当該使用しない期間においては、この限りでない。
abnormalities in rotor;
回転体の異常の有無
abnormalities in bearing parts of the main shafts;
主軸の軸受部の異常の有無
abnormalities in brake;
ブレーキの異常の有無
abnormalities in the outer frame; and
外わくの異常の有無
the slackness of a bolt used in the parts listed in each preceding item.
前各号に掲げる部分のボルトのゆるみの有無
As regards the centrifugal machine set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the use.
When having carried out the self-inspections set forth in the preceding two paragraphs, the employer must record the following matters and preserve the record for three years:
事業者は、前二項の自主検査を行つたときは、次の事項を記録し、これを三年間保存しなければならない。
the date of the inspection;
検査年月日
the method of the inspection;
検査方法
the parts inspected;
検査箇所
the results of the inspection;
検査の結果
the name of the person who has carried out the inspection; and
検査を実施した者の氏名
when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.
検査の結果に基づいて補修等の措置を講じたときは、その内容
When having found any abnormality in carrying out the self-inspection set forth in paragraph (1) or paragraph (2), the employer must make repairs or take other necessary measures.
略称規定第五条第一項第一号イ
学校教育法(昭和二十二年法律第二十六号)による大学(旧大学令(大正七年勅令第三百八十八号)による大学を含む。以下同じ。)又は高等専門学校(旧専門学校令(明治三十六年勅令第六十一号)による専門学校を含む。以下同じ。)における理科系統の正規の…
わかりやすく言うと
学士の学位を授与することもある独立行政法人、大学改革支援・学位授与機構を略した呼び名です。
略称規定第五条第一項第一号イ
学校教育法(昭和二十二年法律第二十六号)による大学(旧大学令(大正七年勅令第三百八十八号)による大学を含む。以下同じ。)又は高等専門学校(旧専門学校令(明治三十六年勅令第六十一号)による専門学校を含む。以下同じ。)における理科系統の正規の…
わかりやすく言うと
学校教育法による専門職大学の前期課程のことです。
略称規定第二十四条の十三第一項
労働者に危険を及ぼし、又は労働者の健康障害をその使用により生ずるおそれのある機械(以下単に「機械」という。)を譲渡し、又は貸与する者(次項において「機械譲渡者等」という。)は、文書の交付等により当該機械に関する次に掲げる事項を…
わかりやすく言うと
使うことによって労働者に危険を及ぼし、又は労働者の健康障害を生ずるおそれのある機械のことです。
略称規定第三十六条第一項第二号
動力により駆動されるプレス機械(以下「動力プレス」という。)の金型、シヤーの刃部又はプレス機械若しくはシヤーの安全装置若しくは安全囲いの取付け、取外し又は調整の業務
略称規定第百三十一条第一項
事業者は、プレス機械及びシヤー(以下「プレス等」という。)については、安全囲いを設ける等当該プレス等を用いて作業を行う労働者の身体の一部が危険限界に入らないような措置を講じなければならない。
わかりやすく言うと
プレス機械とシヤーをまとめた呼び名です。
略称規定第百三十五条の三第一項
動力プレスに係る法第四十五条第二項の厚生労働省令で定める自主検査(以下「特定自主検査」という。)は、第百三十四条の三に規定する自主検査とする。
わかりやすく言うと
動力プレスについて第百三十四条の三が定める自主検査で、一年以内ごとに一回の定期のものと、長く使わなかった動力プレスの使用を再び始めるときのもののことです。資格を持つ者又は検査業者が行います(労働安全衛生法第四十五条第二項)。
略称規定第百三十五条の三第三項
動力プレスに係る特定自主検査を法第四十五条第二項の検査業者(以下「検査業者」という。)に実施させた場合における前条の規定の適用については、同条第五号中「検査を実施した者の氏名」とあるのは、「検査業者の名称」とする。
わかりやすく言うと
労働安全衛生法第五十四条の三第一項の登録を受けて、他人の求めに応じて機械等の特定自主検査を行う者のことです(労働安全衛生法第四十五条第二項)。
作業主任者
高圧室内作業その他の労働災害を防止するための管理が必要な作業で政令で定めるものについて、事業者が、作業の区分に応じて選任しなければならない人で、その作業に従事する労働者の指揮その他の厚生労働省令で定める事項を行います(労働安全衛生法第十四条)。都道府県労働局長の免許を受けた人か、都道府県労働局長の登録を受けた者が行う技能講習を修了した人の中から選びます(同条)。政令で定める業種の事業場では、新たに職長など作業中の労働者を直接指導や監督する立場についた人に安全や衛生のための教育を行わなければなりませんが、作業主任者はその対象から除かれています(同法第六十条第一項)。
労働安全衛生法第14条・第60条を参考にAIが作成。