第一節 明り掘削の作業
Section 1 Open-Cut Excavating Work
第一款 掘削の時期及び順序等
Subsection 1 Time and Procedures of Excavating Work
Article 355Investigation on the Workplace
In carrying out the excavating work of natural ground, when there is a risk of endangering workers due to collapse of natural ground, damage to underground-installed objects, etc., the employer must investigate in advance the workplace and natural ground surrounding the workplace regarding the following matters by boring or other appropriate methods, determine the time and procedures of excavation that conforms to what became known by the investigation, and carry out the work according to the procedures determined:
事業者は、地山の掘削の作業を行う場合において、地山の崩壊、埋設物等の損壊等により労働者に危険を及ぼすおそれのあるときは、あらかじめ、作業箇所及びその周辺の地山について次の事項をボーリングその他適当な方法により調査し、これらの事項について知り得たところに適応する掘削の時期及び順序を定めて、当該定めにより作業を行わなければならない。
landform, nature of the soil and conditions of strata;
形状、地質及び地層の状態
existence and condition of cracks, water content, spring water and freezing;
き裂、含水、湧水及び凍結の有無及び状態
existence and condition of underground-installed objects, etc.; and
埋設物等の有無及び状態
existence and condition of high-temperature gas and vapor.
高温のガス及び蒸気の有無及び状態
Article 356Standard for Gradient of the Excavation Surface
When carrying out excavating work of natural ground (excluding natural ground composed of rock beds without cracks that cause collapse or fall of rocks, natural ground composed of sand, and natural ground in a condition which is liable to collapse due to blasting etc.; hereinafter the same applies in this Article) by the method of manual excavation (meaning the method of excavation without using excavating machines such as a power shovel and tractor shovel; hereinafter the same applies in the following Article), the employer must make the gradient of the excavation surface (in the case that there is a horizontal step with a depth of 2 m or more on the excavation surface, meaning each excavation surface divided by the horizontal step; the same applies hereinafter) the value equal to or less than that listed in the right column of the following Table in accordance with the type of the ground listed in the left column and the height of the excavation surface listed in the middle column of the same Table, respectively:
| Type of the Natural Ground | Height of the Excavation Surface (Unit: m) | Gradient of the Excavation Surface (Unit: Degrees) |
| natural ground composed of rock beds or hard clay | Less than 5 | 90 |
| 5 or more | 75 | |
| other natural ground | Less than 2 | 90 |
| 2 or more and less than 5 | 75 | |
| 5 or more | 60 |
事業者は、手掘り(パワー・シヨベル、トラクター・シヨベル等の掘削機械を用いないで行なう掘削の方法をいう。以下次条において同じ。)により地山(崩壊又は岩石の落下の原因となるき裂がない岩盤からなる地山、砂からなる地山及び発破等により崩壊しやすい状態になつている地山を除く。以下この条において同じ。)の掘削の作業を行なうときは、掘削面(掘削面に奥行きが二メートル以上の水平な段があるときは、当該段により区切られるそれぞれの掘削面をいう。以下同じ。)のこう配を、次の表の上欄に掲げる地山の種類及び同表の中欄に掲げる掘削面の高さに応じ、それぞれ同表の下欄に掲げる値以下としなければならない。
| 地山の種類 | 掘削面の高さ(単位 メートル) | 掘削面のこう配(単位 度) |
| 岩盤又は堅い粘土からなる地山 | 五未満 | 九十 |
| 五以上 | 七十五 | |
| その他の地山 | 二未満 | 九十 |
| 二以上五未満 | 七十五 | |
| 五以上 | 六十 |
In the case referred to in the preceding paragraph, when it is not possible to calculate the gradient because there are parts of the excavation surface that differ in slope from other parts, the slopes of the part of the excavation surface must be maintained so that the danger of collapse may not become greater than that prescribed in the same paragraph.
Article 357
When carrying out the excavating work of natural ground composed of sand or of natural ground in a condition liable to collapse due to blasting, etc., by manual excavation, the employer must comply with requirements set forth in the following items:
事業者は、手掘りにより砂からなる地山又は発破等により崩壊しやすい状態になつている地山の掘削の作業を行なうときは、次に定めるところによらなければならない。
for natural ground composed of sand, to make the gradient of the excavation surface 35 degrees or less, or make the height of the excavation surface less than 5 m; and
砂からなる地山にあつては、掘削面のこう配を三十五度以下とし、又は掘削面の高さを五メートル未満とすること。
for natural ground in a condition liable to collapse due to blasting, etc., to make the gradient of the excavation surface 45 degrees or less, or make the height of the excavation surface less than 2 m.
発破等により崩壊しやすい状態になつている地山にあつては、掘削面のこう配を四十五度以下とし、又は掘削面の高さを二メートル未満とすること。
The provisions of paragraph (2) of the preceding Article apply mutatis mutandis to the case where it is not possible to calculate the gradient because parts of the excavation surface of the natural ground set forth in the preceding paragraph differ in slope from other parts.
Article 358Inspection
When carrying out the work of open-cut excavation, the employer must take the following measures to prevent workers from dangers due to collapse of natural ground or fallen earth and rocks:
事業者は、明り掘削の作業を行なうときは、地山の崩壊又は土石の落下による労働者の危険を防止するため、次の措置を講じなければならない。
to designate an inspector and have the inspector check the workplace and the natural ground surrounding the workplace before commencing the work for the day, after a heavy rain and a moderate or greater earthquake on the existence and condition of loose stones and cracks, and changes in water content, spring water and freezing conditions; and
点検者を指名して、作業箇所及びその周辺の地山について、その日の作業を開始する前、大雨の後及び中震以上の地震の後、浮石及びき裂の有無及び状態並びに含水、湧水及び凍結の状態の変化を点検させること。
to designate an inspector and have the inspector check for the existence and condition of loose stones and cracks, after blasting work, at places where the blasting work has been carried out and their surroundings.
点検者を指名して、発破を行なつた後、当該発破を行なつた箇所及びその周辺の浮石及びき裂の有無及び状態を点検させること。
Article 359Appointment of Operations Supervisor of Excavating Natural Ground
As regards the work set forth in Article 6, item (ix) of the Order, the employer must appoint an operations supervisor of excavating natural ground from the persons who have completed the skill training course for operations supervisor of excavating natural ground and shoring.
事業者は、令第六条第九号の作業については、地山の掘削及び土止め支保工作業主任者技能講習を修了した者のうちから、地山の掘削作業主任者を選任しなければならない。
Article 360Duties of the Operations Supervisor of Excavating Natural Ground
The employer must have the operations supervisor of excavating natural ground carry out the following matters:
事業者は、地山の掘削作業主任者に、次の事項を行わせなければならない。
to decide the work method and directly supervise the work;
作業の方法を決定し、作業を直接指揮すること。
to inspect the instruments and tools, and remove those defective; and
器具及び工具を点検し、不良品を取り除くこと。
to monitor the use of fall arrest equipment with the required performance, etc. and safety helmets.
要求性能墜落制止用器具等及び保護帽の使用状況を監視すること。
Article 361Prevention of Dangers Due to Collapse of Natural Ground
When carrying out open-cut excavation work, if there is a risk of causing danger due to collapse of natural ground or falling of earth and rocks, the employer must, in advance, take measures to prevent the danger, such as setting up shoring, setting up protective nets and prohibiting persons engaged in work at the workshop from entering.
事業者は、明り掘削の作業を行う場合において、地山の崩壊又は土石の落下により危険を及ぼすおそれのあるときは、あらかじめ、土止め支保工を設け、防護網を張り、当該作業場において作業に従事する作業従事者の立入りを禁止する等当該危険を防止するための措置を講じなければならない。
Article 362Prevention of Dangers Due to Underground-Installed Objects
When carrying out open-cut excavation work at a place in the vicinity of underground installations, etc. or structures such as brick walls, concrete block walls and retaining walls, if there is a risk of endangering workers due to their damage, etc., the employer must not carry out the work unless measures to prevent the danger, such as reinforcing or relocating them, have been taken.
事業者は、埋設物等又はれんが壁、コンクリートブロツク塀、擁壁等の建設物に近接する箇所で明り掘削の作業を行なう場合において、これらの損壊等により労働者に危険を及ぼすおそれのあるときは、これらを補強し、移設する等当該危険を防止するための措置が講じられた後でなければ、作業を行なつてはならない。
The measures set forth in the preceding paragraph, in the case where there is a risk of endangering workers due to damage to a gas conduit exposed by open-cut excavation work, must be measures such as protecting the gas conduit by suspension protection, support protection, etc., or relocating the gas conduit.
明り掘削の作業により露出したガス導管の損壊により労働者に危険を及ぼすおそれのある場合の前項の措置は、つり防護、受け防護等による当該ガス導管についての防護を行ない、又は当該ガス導管を移設する等の措置でなければならない。
As regards the work for protecting gas conduits prescribed in the preceding paragraph, the employer must designate a person to supervise the work, and have the work carried out under the direct supervision by the person.
事業者は、前項のガス導管の防護の作業については、当該作業を指揮する者を指名して、その者の直接の指揮のもとに当該作業を行なわせなければならない。
Article 363Prohibition of Using Excavating Machines
In carrying out the open-cut excavation work, when there is a risk of endangering workers due to damage to gas conduits, underground electric line or other underground structures by the use of excavating machine, loading and transporting machines, the employer must not use those machines.
事業者は、明り掘削の作業を行なう場合において、掘削機械、積込機械及び運搬機械の使用によるガス導管、地中電線路その他地下に存する工作物の損壊により労働者に危険を及ぼすおそれのあるときは、これらの機械を使用してはならない。
Article 364Traveling Route of Transporting Machines
When carrying out the open-cut excavation work, the employer must determine in advance the traveling route for the transporting machine, excavating machine and loading machine (excluding a vehicle type construction equipment and a vehicle type material handling machine, etc.; hereinafter referred to as "transporting machine, etc." in this Chapter), and the method for entering and leaving the place for those machines to load and unload the earth and rocks, and make them known to the workers concerned.
事業者は、明り掘削の作業を行うときは、あらかじめ、運搬機械、掘削機械及び積込機械(車両系建設機械及び車両系荷役運搬機械等を除く。以下この章において「運搬機械等」という。)の運行の経路並びにこれらの機械の土石の積卸し場所への出入の方法を定めて、これを関係労働者に周知させなければならない。
Article 365Arrangement of a Guide
When carrying out open-cut excavation work, if a transporting machine, etc. approaches the work location by going backwards or there is a risk of its falling, the employer must place a guide and have that person guide these machines.
The operator of the transporting machine, etc., set forth in the preceding paragraph must follow the instruction given by the guide set forth in the same paragraph.
Article 366Wearing Safety Helmets
When carrying out the work of open-cut excavation, the employer must have the worker engaging in the work wear a safety helmet in order to prevent workers from dangers due to objects that come flying or falling.
事業者は、明り掘削の作業を行なうときは、物体の飛来又は落下による労働者の危険を防止するため、当該作業に従事する労働者に保護帽を着用させなければならない。
The worker engaging in the work set forth in the preceding paragraph must wear the safety helmet set forth in the same paragraph.
Article 367Maintenance of Illumination
As regards the place where the work of an open-cut excavation is carried out, the employer must maintain necessary illumination for safely carrying out the work.
事業者は、明り掘削の作業を行なう場所については、当該作業を安全に行なうため必要な照度を保持しなければならない。
第二款 土止め支保工
Subsection 2 Shoring
Article 368Material
As regards materials of shoring, the employer must not use those having marked damage, deformation or corrosion.
事業者は、土止め支保工の材料については、著しい損傷、変形又は腐食があるものを使用してはならない。
Article 369Structure
The employer must make the structure of the shoring solid in accordance with the condition of landform, nature of the soil, strata, cracks, water content, spring water, freezing and underground-installed objects, etc., pertaining to the natural ground where the shoring is to be installed.
事業者は、土止め支保工の構造については、当該土止め支保工を設ける箇所の地山に係る形状、地質、地層、き裂、含水、湧水、凍結及び埋設物等の状態に応じた堅固なものとしなければならない。
Article 370Assembly Drawing
When assembling the shoring, the employer must prepare an assembly drawing in advance, and assemble the shoring according to the drawing.
事業者は、土止め支保工を組み立てるときは、あらかじめ、組立図を作成し、かつ、当該組立図により組み立てなければならない。
The assembly drawing set forth in the preceding paragraph must indicate the arrangement, size and materials of components such as sheet piles, piles, shore laggings, wales, struts, and the time and procedures of installation.
前項の組立図は、矢板、くい、背板、腹おこし、切りばり等の部材の配置、寸法及び材質並びに取付けの時期及び順序が示されているものでなければならない。
Article 371Installation of Components
As regards installation, etc. of the components of the shoring, the employer must comply with the requirements set forth in the following items:
事業者は、土止め支保工の部材の取付け等については、次に定めるところによらなければならない。
to firmly mount the wales and struts on sheet piles, piles, etc., to prevent them from coming off;
切りばり及び腹おこしは、脱落を防止するため、矢板、くい等に確実に取り付けること。
to use butt joints for joints of compression components (excluding angle braces);
圧縮材(火打ちを除く。)の継手は、突合せ継手とすること。
to firmly fasten the connecting parts of struts or angle braces and the crossing parts of struts with doubling plates and bolts, or connect them by welding or other methods to make them solid;
切りばり又は火打ちの接続部及び切りばりと切りばりとの交さ部は、当て板をあててボルトにより緊結し、溶接により接合する等の方法により堅固なものとすること。
for shoring with a middle support pole, to firmly mount struts on the middle support pole; and
中間支持柱を備えた土止め支保工にあつては、切りばりを当該中間支持柱に確実に取り付けること。
when struts are supported by things other than the components such as the columns of a building, to make the supports strong enough to bear the load applied.
切りばりを建築物の柱等部材以外の物により支持する場合にあつては、当該支持物は、これにかかる荷重に耐えうるものとすること。
Article 372Work of Installing or Removing Struts
When carrying out the work set forth in Article 6, item (x) of the Order, the employer must take the following measures:
事業者は、令第六条第十号の作業を行うときは、次の措置を講じなければならない。
to prohibit persons other than persons engaged in work concerned from entering the place where the work is carried out, by indicating the prohibition in a conspicuous place or by other methods;
当該作業を行う箇所に関係する作業従事者以外の者が立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止すること。
when raising or lowering materials, instruments or tools, to have workers use lifting ropes, lifting bags, etc.
材料、器具又は工具を上げ、又は下ろすときは、つり綱、つり袋等を労働者に使用させること。
Article 373Inspection
When having installed shoring, the employer must inspect the following matters once every period not exceeding seven days, after a moderate or greater earthquake, and after the occurrence of a situation that has a risk of rapidly weakening the ground due to heavy rain, etc., and immediately reinforce or make repairs when having found any abnormality:
事業者は、土止め支保工を設けたときは、その後七日をこえない期間ごと、中震以上の地震の後及び大雨等により地山が急激に軟弱化するおそれのある事態が生じた後に、次の事項について点検し、異常を認めたときは、直ちに、補強し、又は補修しなければならない。
existence and condition of damage, deformation, corrosion, displacement and coming off of components;
部材の損傷、変形、腐食、変位及び脱落の有無及び状態
degree of compression of struts; and
切りばりの緊圧の度合
condition of the connecting parts, mounting parts and crossing parts of components.
部材の接続部、取付け部及び交さ部の状態
Article 374Appointment of Operations Supervisor of Shoring
As regards the work set forth in Article 6, item (x) of the Order, the employer must appoint an operations supervisor of shoring from the persons who have completed the skill training courses for operations supervisor of excavating natural ground and shoring.
事業者は、令第六条第十号の作業については、地山の掘削及び土止め支保工作業主任者技能講習を修了した者のうちから、土止め支保工作業主任者を選任しなければならない。
Article 375Duties of the Operations Supervisor of Shoring
The employer must have the operations supervisor of shoring carry out the following matters:
事業者は、土止め支保工作業主任者に、次の事項を行わせなければならない。
to decide the work method and directly supervise the work;
作業の方法を決定し、作業を直接指揮すること。
to check for defects in material and inspect instruments and tools, and remove those defective; and
材料の欠点の有無並びに器具及び工具を点検し、不良品を取り除くこと。
to monitor the use of fall arrest equipment with the required performance, etc. and safety helmets.
要求性能墜落制止用器具等及び保護帽の使用状況を監視すること。
略称規定第十六条第二項
事業者は、令第六条第十七号の作業のうち、圧縮水素、圧縮天然ガス又は液化天然ガスを燃料とする自動車(道路運送車両法(昭和二十六年法律第百八十五号)に規定する普通自動車、小型自動車又は軽自動車(同法第五十八条第一項に規定する検査対象外軽自動車…
わかりやすく言うと
人や物品を運ぶかどうかにかかわらず、自動車などをその装置の使い方に従って用いることです。道路以外の場所だけで用いることは含みません(道路運送車両法第二条第五項)。
略称規定第二十四条の十三第一項
労働者に危険を及ぼし、又は労働者の健康障害をその使用により生ずるおそれのある機械(以下単に「機械」という。)を譲渡し、又は貸与する者(次項において「機械譲渡者等」という。)は、文書の交付等により当該機械に関する次に掲げる事項を…
わかりやすく言うと
使うことによって労働者に危険を及ぼし、又は労働者の健康障害を生ずるおそれのある機械のことです。
略称規定第九十四条の二第一項第一号イ・この規定及び第六百三十四条の二及び第二編第六章第一節の中だけ
埋設物その他地下に存する工作物(第二編第六章第一節及び第六百三十四条の二において「埋設物等」という。)がふくそうする場所に近接する場所で行われるもの
わかりやすく言うと
地中に埋設された物その他の地下にある工作物のことです。
定義第九十四条の二第一項第二号
令別表第七に掲げる建設機械で、動力を用い、かつ、不特定の場所に自走できるもの
わかりやすく言うと
整地・運搬・積込み用機械、掘削用機械、基礎工事用機械、締固め用機械、コンクリート打設用機械、解体用機械として労働安全衛生法施行令別表第七に並べられた建設機械で、動力を使い、不特定の場所に自走できるもののことです。
略称規定第百三十条の五第三項
労働者は、第一項ただし書の場合において、要求性能墜落制止用器具その他の命綱(以下「要求性能墜落制止用器具等」という。)の使用を命じられたときは、これを使用しなければならない。
わかりやすく言うと
墜落による危険のおそれに応じた性能を持つ墜落制止用器具(要求性能墜落制止用器具)その他の命綱のことです。
定義第百五十一条の二第一項・法令全体に適用
次の各号のいずれかに該当するもの
わかりやすく言うと
フォークリフト、ショベルローダー、フォークローダー、ストラドルキャリヤー、不整地運搬車、構内運搬車、貨物自動車のことです。構内運搬車は、一定の大きさ以下で最高速度が毎時十五キロメートル以下の、専ら荷を運ぶ自動車です。
略称規定第三百六十四条第一項・この章の中だけ
事業者は、明り掘削の作業を行うときは、あらかじめ、運搬機械、掘削機械及び積込機械(車両系建設機械及び車両系荷役運搬機械等を除く。以下この章において「運搬機械等」という。)の運行の経路並びにこれらの機械の土石の積卸し場所への出入の方法を定め…
わかりやすく言うと
明り掘削の作業で使う運搬機械、掘削機械及び積込機械のうち、車両系建設機械と車両系荷役運搬機械等を除いたもののことです。この章の中で使われます。
作業主任者
高圧室内作業その他の労働災害を防止するための管理が必要な作業で政令で定めるものについて、事業者が、作業の区分に応じて選任しなければならない人で、その作業に従事する労働者の指揮その他の厚生労働省令で定める事項を行います(労働安全衛生法第十四条)。都道府県労働局長の免許を受けた人か、都道府県労働局長の登録を受けた者が行う技能講習を修了した人の中から選びます(同条)。政令で定める業種の事業場では、新たに職長など作業中の労働者を直接指導や監督する立場についた人に安全や衛生のための教育を行わなければなりませんが、作業主任者はその対象から除かれています(同法第六十条第一項)。
労働安全衛生法第14条・第60条を参考にAIが作成。