Article 314Appointment of Operations Supervisor of Gas Welding
As regards the work set forth in Article 6, item (ii) of the Order, the employer must appoint operations supervisor of gas welding from persons who have the license of operations supervisor of gas welding.
事業者は、令第六条第二号の作業については、ガス溶接作業主任者免許を有する者のうちから、ガス溶接作業主任者を選任しなければならない。
Article 315Duties of an Operations Supervisor of Gas Welding
When carrying out work of welding, fusing or heating metal using an acetylene welding equipment, the employer must have the operations supervisor of gas welding carry out the following matters:
事業者は、アセチレン溶接装置を用いて金属の溶接、溶断又は加熱の作業を行なうときは、ガス溶接作業主任者に、次の事項を行なわせなければならない。
to decide the work method, and supervise the work;
作業の方法を決定し、作業を指揮すること。
to have the worker engaging in handling acetylene welding equipment carry out the following matters:
アセチレン溶接装置の取扱いに従事する労働者に次の事項を行なわせること。
to not use a tool which is likely to produce sparks for, or give shocks to, the generator being used;
使用中の発生器に、火花を発するおそれのある工具を使用し、又は衝撃を与えないこと。
when inspecting gas leakage from acetylene welding equipment, to use a safe method such as using soap water;
アセチレン溶接装置のガス漏れを点検するときは、石けん水を使用する等安全な方法によること。
to not leave the door of the entrance to the generator room open;
発生器室の出入口の戸を開放しておかないこと。
when recharging carbide to the generator of portable acetylene welding equipment, to carry out the operations at a safe place outdoors; and
when opening a carbide can, to not perform acts that are likely to produce sparks, such as giving shocks;
カーバイド罐を開封するときは、衝撃その他火花を発するおそれのある行為をしないこと。
when starting the work, to inspect the acetylene welding equipment, and when a mixed gas of air and acetylene exists in the generator, to remove the mixed gas;
to place the safety equipment at a place where its water-level can easily be inspected during operations, and inspect the safety device more than once a day;
安全器は、作業中、その水位を容易に確かめることができる箇所に置き、かつ、一日一回以上これを点検すること。
when keeping the acetylene welding equipment warm or heating the equipment to prevent water in the equipment from freezing, to use a safe method, such as using warm water or steam;
アセチレン溶接装置内の水の凍結を防ぐために、保温し、又は加温するときは、温水又は蒸気を使用する等安全な方法によること。
when suspending the use of the generator, to keep the water level in its water chamber in a condition that the water and residual carbide may not come into contact each other;
発生器の使用を休止するときは、その水室の水位を水と残留カーバイドが接触しない状態に保つこと。
when repairing, processing, transporting or storing the generator, or suspending its use continuously, to completely remove the acetylene and carbide from the generator;
発生器の修繕、加工、運搬若しくは格納をしようとするとき、又はその使用を継続して休止しようとするときは、アセチレン及びカーバイドを完全に除去すること。
to dispose carbide sludge in a safe manner such as keeping it in a sludge pit until the danger due to gas is removed;
カーバイドのかすは、ガスによる危険がなくなるまでかすだめに入れる等安全に処置すること。
to monitor the use of eye protector and protective gloves by workers engaged in the work; and
当該作業に従事する労働者の保護眼鏡及び保護手袋の使用状況を監視すること。
to carry the license of operations supervisor of gas welding.
ガス溶接作業主任者免許証を携帯すること。
Article 316
When carrying out the work of welding, fusing or heating metal using the gas welding equipment using manifolds, the employer must have the operations supervisor of gas welding carry out the following matters:
事業者は、ガス集合溶接装置を用いて金属の溶接、溶断又は加熱の作業を行なうときは、ガス溶接作業主任者に次の事項を行なわせなければならない。
to decide the work method and supervise the work;
作業の方法を決定し、作業を指揮すること。
to have the worker engaging in the handling of the gas manifolds carry out the following matters:
ガス集合装置の取扱いに従事する労働者に次の事項を行なわせること。
to remove oil, etc., and dust, etc., adhering to the mouthpiece of the gas cylinder and the mounting opening of the piping;
取り付けるガスの容器の口金及び配管の取付け口に付着している油類、じんあい等を除去すること。
when having exchanged gas cylinders, to inspect the mouthpiece of the gas cylinder and the mounting opening of the piping for leakage of gas, and remove the mixed gas of the gas and air in the piping;
ガスの容器の取替えを行なつたときは、当該容器の口金及び配管の取付け口の部分のガス漏れを点検し、かつ、配管内の当該ガスと空気との混合ガスを排除すること。
when inspecting leakage of gas, to use a safe method such as using soap water;
ガス漏れを点検するときは、石けん水を使用する等安全な方法によること。
to open and close the valve or cock gently;
バルブ又はコツクの開閉を静かに行なうこと。
to be present when the gas cylinders are exchanged;
ガスの容器の取替えの作業に立ち合うこと。
when commencing the work, to inspect the hose, blowpipe, hose band, etc., and when having found that there is a risk of leakage of gas or oxygen due to the damage, wear, etc., to repair or exchange the parts damaged, worn, etc.;
当該作業を開始するときは、ホース、吹管、ホースバンド等の器具を点検し、損傷、摩耗等によりガス又は酸素が漏えいするおそれがあると認めたときは、補修し、又は取り替えること。
to place the safety equipment at a place where its functions can easily be confirmed, and inspect the safety device more than once a day;
安全器は、作業中、その機能を容易に確かめることができる箇所に置き、かつ、一日一回以上これを点検すること。
to monitor the use of eye protector and protective gloves by workers engaged in the work; and
当該作業に従事する労働者の保護眼鏡及び保護手袋の使用状況を監視すること。
to carry the license of operations supervisor of gas welding.
ガス溶接作業主任者免許証を携帯すること。
Article 317Periodical Self-inspection
As regards an acetylene welding equipment or a gas welding equipment using manifolds (excluding the parts of the piping of those devices installed underground; hereinafter the same applies in this Article), the employer must carry out a self-inspection on the existence of damage, deformation, corrosion, etc., and the functions of the equipment periodically once every period not exceeding one year; provided, however, that this does not apply to the non-use period of acetylene welding equipment or a gas welding equipment using manifolds, which is not used for a period exceeding one year.
As regards the acetylene welding equipment or gas welding equipment using manifolds referred to in the proviso of the preceding paragraph, the employer must carry out a self-inspection for the matters prescribed in the same paragraph before resuming the operation.
When an abnormality is found in the acetylene welding equipment or gas welding equipment using manifolds as a result of the self-inspection referred to in the preceding two paragraphs, the employer must not use the equipment unless repairs are made or other necessary measures have been taken.
When having carried out the self-inspection set forth in paragraph (1) or (2), the employer must record the following matters and preserve the record for three years:
the date of the inspection;
検査年月日
the method of the inspection;
検査方法
the parts inspected;
検査箇所
the results of the inspection;
検査の結果
the name of the person who has carried out the inspection; and
検査を実施した者の氏名
when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.
検査の結果に基づいて補修等の措置を講じたときは、その内容
第七節 発破の作業
Section 7 Blasting Work
Article 318Standards of Blasting Work
The employer must have the worker engaging in the work set forth in Article 20, item (i) of the Order (hereinafter referred to as "blasting work") carry out the following matters:
事業者は、令第二十条第一号の業務(以下「発破の業務」という。)に従事する労働者に次の事項を行わせなければならない。
to not defreeze the frozen dynamite by a dangerous method, such as bringing it in proximity to fire or into direct contact with a steam pipe or other high-temperature objects;
凍結したダイナマイトは、火気に接近させ、蒸気管その他の高熱物に直接接触させる等危険な方法で融解しないこと。
when charging gunpowder or explosives, to not use naked fire or smoke in the vicinity;
火薬又は爆薬を装塡するときは、その付近で裸火の使用又は喫煙をしないこと。
to use a safe charging tool, which are unlikely to cause an explosion due to friction, shock, static electricity, etc.;
装塡具は、摩擦、衝撃、静電気等による爆発を生ずるおそれのない安全なものを使用すること。
to use a safe stemming, which are unlikely to cause an ignition or an inflammation, such as clay or sand;
込物は、粘土、砂その他の発火又は引火の危険のないものを使用すること。
when the charged gunpowder does not explode after ignition, or when it is difficult to confirm that the charged gunpowder has exploded, to comply with the requirements set forth in the following sub-items:
点火後、装塡された火薬類が爆発しないとき、又は装塡された火薬類が爆発したことの確認が困難であるときは、次に定めるところによること。
when an electric detonator is used, to remove the blasting leading wire from the igniter and short-circuit the end of the wire, and take measures to prevent re-ignition; and not to approach the place where the gunpowder is charged within five minutes after the measures are taken; and
電気雷管によつたときは、発破母線を点火器から取り外し、その端を短絡させておき、かつ、再点火できないように措置を講じ、その後五分以上経過した後でなければ、火薬類の装塡箇所に接近しないこと。
when device other than an electric detonator is used, not to approach the place where the gunpowder is charged within 15 minutes after ignition.
電気雷管以外のものによつたときは、点火後十五分以上経過した後でなければ、火薬類の装塡箇所に接近しないこと。
The worker engaging in the work set forth in the preceding paragraph must carry out the matters listed in each item of the same paragraph.
When charging gunpowder or explosives, the employer must prohibit the use of naked fire or smoking in the vicinity by persons engaged in work (excluding workers) who engage in blasting work, by indicating the prohibition in a conspicuous place or by other methods.
A person engaged in work (excluding a worker) who engages in the blasting work referred to in the preceding paragraph must not use naked fire or smoke in the vicinity where gunpowder or explosives are being charged.
Article 319Supervisor for Fuse Blasting Work
When carrying out fuse blasting work, the employer must appoint a supervisor from those eligible for the work, and have the supervisor carry out the following matters:
事業者は、導火線発破の作業を行なうときは、発破の業務につくことができる者のうちから作業の指揮者を定め、その者に次の事項を行なわせなければならない。
to instruct workers other than those engaging in igniting work to evacuate the workplace before ignition;
点火前に、点火作業に従事する労働者以外の労働者に対して、退避を指示すること。
to indicate the place for evacuation and the route to that place to workers engaging in the igniting work;
点火作業に従事する労働者に対して、退避の場所及び経路を指示すること。
when a worker takes charge of five or more ignitions at a time, have each worker use device that notifies the time of evacuation such as a blasting watch or waste fuses;
一人の点火数が同時に五以上のときは、発破時計、捨て導火線等の退避時期を知らせる物を使用すること。
to instruct workers on the procedures and specification of the igniting work;
点火の順序及び区分について指示すること。
to give a signal of ignition;
点火の合図をすること。
to give a signal of evacuation to workers who engaged in the igniting work; and
点火作業に従事した労働者に対して、退避の合図をすること。
to check for misfires or residual gunpowder.
不発の装薬又は残薬の有無について点検すること。
The supervisor for fuse blasting work must carry out the matters listed in each item of the preceding paragraph.
導火線発破の作業の指揮者は、前項各号に掲げる事項を行なわなければならない。
The worker who engages in the fuse blasting work must follow the instructions and signals given by the supervisor pursuant to the provisions of the preceding paragraph.
導火線発破の作業に従事する労働者は、前項の規定により指揮者が行なう指示及び合図に従わなければならない。
Article 320Supervisor for Electric Blasting Work
When carrying out electric blasting work, the employer must appoint a supervisor from those eligible for the work and have the supervisor carry out the matters set forth in paragraph (1), items (v) and (vii) of the preceding Article and the following matters:
to indicate the place for evacuation and the route to that place to the workers engaging in the work;
当該作業に従事する労働者に対し、退避の場所及び経路を指示すること。
to confirm that workers have been evacuated from the dangerous area before ignition;
点火前に危険区域内から労働者が退避したことを確認すること。
to appoint a person in charge of the ignition; and
点火者を定めること。
to give instruction on the place of ignition.
点火場所について指示すること。
The supervisor of the electric blasting work must carry out the matters listed in each item of the preceding paragraph.
電気発破の作業の指揮者は、前項各号に掲げる事項を行なわなければならない。
The worker engaging in the electric blasting work must follow the instructions and signals given by the supervisor pursuant to the provisions of the preceding paragraph.
電気発破の作業に従事する労働者は、前項の規定により指揮者が行なう指示及び合図に従わなければならない。
定義第三百一条第一項
令第一条第一号に掲げるアセチレン溶接装置
わかりやすく言うと
アセチレン発生器、安全器、導管、吹管などで構成され、溶解アセチレン以外のアセチレンと酸素を使って、金属を溶接し、溶断し、又は加熱する設備のことです(労働安全衛生法施行令第一条第一号)。
略称規定第三百二条第一項
事業者は、アセチレン溶接装置のアセチレン発生器(以下「発生器」という。)については、専用の発生器室(以下「発生器室」という。)内に設けなければならない。
略称規定第三百二条第一項
事業者は、アセチレン溶接装置のアセチレン発生器(以下「発生器」という。)については、専用の発生器室(以下「発生器室」という。)内に設けなければならない。
略称規定第三百八条第一項
事業者は、令第一条第二号のガス集合装置(以下「ガス集合装置」という。)については、火気を使用する設備から五メートル以上離れた場所に設けなければならない。
わかりやすく言うと
十以上の可燃性ガスの容器を導管でつないだ装置か、九以下の容器をつないだ装置で、容器の内容積の合計が水素や溶解アセチレンでは四百リットル以上、その他の可燃性ガスでは千リットル以上のもののことです(労働安全衛生法施行令第一条第二号)。
略称規定第三百十条第一項
事業者は、令第一条第二号に掲げるガス集合溶接装置(以下「ガス集合溶接装置」という。)の配管については、次に定めるところによらなければならない。
わかりやすく言うと
ガス集合装置(可燃性ガスの容器を導管でつないだ一定規模以上の装置)、安全器、圧力調整器、導管、吹管などで構成され、可燃性ガスと酸素を使って金属を溶接し、溶断し、又は加熱する設備のことです(労働安全衛生法施行令第一条第二号)。
略称規定第三百十八条第一項
事業者は、令第二十条第一号の業務(以下「発破の業務」という。)に従事する労働者に次の事項を行わせなければならない。
わかりやすく言うと
発破を行う場合の、せん孔、装てん、結線、点火と、不発の装薬又は残薬の点検及び処理の業務のことです(労働安全衛生法施行令第二十条第一号)。
作業主任者
高圧室内作業その他の労働災害を防止するための管理が必要な作業で政令で定めるものについて、事業者が、作業の区分に応じて選任しなければならない人で、その作業に従事する労働者の指揮その他の厚生労働省令で定める事項を行います(労働安全衛生法第十四条)。都道府県労働局長の免許を受けた人か、都道府県労働局長の登録を受けた者が行う技能講習を修了した人の中から選びます(同条)。政令で定める業種の事業場では、新たに職長など作業中の労働者を直接指導や監督する立場についた人に安全や衛生のための教育を行わなければなりませんが、作業主任者はその対象から除かれています(同法第六十条第一項)。
労働安全衛生法第14条・第60条を参考にAIが作成。