Article 187Prohibition of Entry
In order to prevent the danger of a wire rope springing back, or of a sheave, pulley block, etc. coming flying, due to damage to the sheave or pulley block of a pile driver, a pile drawer or a boring machine, or their mounting parts, the employer must prohibit a person engaged in work at the workshop where the pile driver, pile drawer or boring machine is used from entering the inside of the bent part of the hoisting wire rope of the pile driver, pile drawer or boring machine in operation, by indicating the prohibition in a conspicuous place or by other methods.
Article 188Measures to Be Taken When Hoisting Sheet Piles and Rods
When hoisting piles, sheet piles and rods, etc., with a pile driver or a boring machine, the employer must have the operator of the machine hoist piles in a manner that the hook part is located right under the sheave or the pulley block of the machine. The same applies to the case of hoisting a pile or sheet pile by providing a pile driver with a hoisting device such as a gin pole.
事業者は、くい打機又はボーリングマシンで、くい、矢板、ロッド等をつり上げるときは、その玉掛部が巻上げ用みぞ車又は滑車装置の直下になるようにつり上げさせなければならない。くい打機にジンポール等の物上げ装置を取り付けて、くい、矢板等をつり上げる場合においても、同様とする。
Article 189Signals
The employer must set fixed signals for the operation of a pile driver, a pile drawer or a boring machine, designate a person who gives the signals and have the person give the signals when operating the machine.
An operator of a pile driver, a pile drawer or a boring machine must follow the signals set forth in the preceding paragraph.
Article 190Supervision of the Work
When carrying out the work of assembling, disassembling, altering or transfer of a pile driver, a pile drawer or a boring machine, the employer must determine the method, procedures, etc., of the work, and make them known to the workers, designate a person who supervises the operation, and have the workers carry out the work under the direct supervision of the person.
Article 191Transfer of Pile Drivers
When transferring the legs of a pile driver or a pile drawer supported with stayed wires, etc., with the twin pillar, mast, etc., in a standing position, using power-driven winch or other machines, the employer must carry out the operation while braking the movement of the machine securely with a winch, tension blocks, etc., from the opposite side in order to prevent collapse due to the legs being dragged excessively.
Article 192Inspection
When having assembled a pile driver, pile drawer or boring machine, the employer must inspect the following matters, and not allow the use of the machines unless having confirmed that there are no abnormalities:
damage and slackness of joint parts of the machine;
機体の緊結部のゆるみ及び損傷の有無
fitted state of the hoisting wire rope, sheave, and pulley block;
巻上げ用ワイヤロープ、みぞ車及び滑車装置の取付状態
functions of the brake and ratchets of hoisting device;
巻上げ装置のブレーキ及び歯止め装置の機能
installation status of a winch; and
ウインチの据付状態
for a pile driver or a pile drawer of which the top part is secured with stays, the method of fixing the stays and the firmness of the stays.
Article 193Measures to Be Taken in the Case of Slackening the Bracing Wires
When slackening the bracing wires (including temporary bracing wires, hereinafter the same applies in this Article) of a pile driver or a pile drawer, the employer must take appropriate measures such as using tension blocks or winches in order to prevent letting the load exceed the limit of the load the workers engaged in the slackening operation are able to easily support.
Article 194Prevention of Damage to Gas Pipes
When the work using a pile driver or boring machine is carried out and there is a risk of endangering workers due to damage of gas pipes, underground electric lines and other underground structures (hereinafter referred to as "gas pipes, etc." in this Article), the employer must in advance, conduct investigation of the workplace by inquiring the existence of the gas pipes, etc., and confirming their conditions to the person administrating the gas pipes, etc., and take measures in conformity with the matters they have come to know by the investigation.
事業者は、くい打機又はボーリングマシンを使用して作業を行う場合において、ガス導管、地中電線路その他地下に存する工作物(以下この条において「ガス導管等」という。)の損壊により労働者に危険を及ぼすおそれのあるときは、あらかじめ、作業箇所について、ガス導管等の有無及び状態を当該ガス導管等を管理する者に確かめる等の方法により調査し、これらの事項について知り得たところに適応する措置を講じなければならない。
Article 194-2Measures to Be Taken when Attaching Rods
When attaching or removing the rod or bit, etc., of a boring machine, the employer must securely cut off the power rotating the rod, etc., by such means as fixing the clutch lever with a stopper.
事業者は、ボーリングマシンのロッド、ビット等を取り付け又は取り外すときは、クラッチレバーをストッパーで固定する等によりロッド等を回転させる動力を確実に遮断しなければならない。
When removing a rod or attaching or removing a bit, etc., from a boring machine, the employer must securely hold the rod with the rod holder, etc.
事業者は、ボーリングマシンのロッドを取り外すとき及びビット等を取り付け又は取り外すときは、ロッドをロッドホルダー等により確実に保持しなければならない。
Article 194-3Fixing the Hose for a Water Swivel
As regards a hose to be connected to the water swivel of a boring machine, the employer must take measures such as fixing the hose to a tower in order to prevent workers from danger due to the hose being trapped into the rotating parts of the rod, etc.
事業者は、ボーリングマシンのウォータースイベルに接続するホースについては、当該ホースがロッド等の回転部分に巻き込まれることによる労働者の危険を防止するため、当該ホースをやぐらに固定する等の措置を講じなければならない。
第二節の二 ジャッキ式つり上げ機械
Section 2-2 Jack-type Lifting Machines
Article 194-4Holding Mechanisms
The employer must not use a jack-type lifting machine for construction work unless the machine falls under the following requirements:
事業者は、建設工事の作業において使用するジャッキ式つり上げ機械については、次の要件に該当するものでなければ、使用してはならない。
having the necessary strength in accordance with the purpose of use;
使用の目的に適応した必要な強度を有すること。
for holding mechanisms, having the necessary capability to hold a wire rope, etc.;
保持機構については、ワイヤロープ等を保持するために必要な能力を有すること。
having the mechanism to prevent simultaneous opening of all the holding mechanisms; and
すべての保持機構が同時に開放されることを防止する機構を有していること。
being free from marked damage, wear, deformation or corrosion.
著しい損傷、磨耗、変形又は腐食のないものであること。
Article 194-5Work Plan
When carrying out the work of lifting or lowering the load using a jack-type lifting machine in carrying out construction, the employer must establish in advance a work plan and carry out the work according to the work plan.
事業者は、建設工事の作業を行う場合において、ジャッキ式つり上げ機械を用いて荷のつり上げ、つり下げ等の作業を行うときは、あらかじめ、作業計画を定め、かつ、当該作業計画により作業を行わなければならない。
The work plan set forth in the preceding paragraph must indicate the following matters:
前項の作業計画は、次の事項が示されているものでなければならない。
the method and procedures of the work;
作業の方法及び順序
the method for preventing the jack-type lifting machine to be used from collapsing or overturning;
使用するジャッキ式つり上げ機械の崩壊及び倒壊を防止するための方法
the method of installing the equipment for preventing the worker engaged in the work from danger of falling; and
作業に従事する労働者の墜落による危険を防止するための設備の設置の方法
the type and capability of the machinery or other such equipment to be used.
使用する機械等の種類及び能力
When having established the work plan set forth in paragraph (1), the employer must make the matters set forth in each item of the preceding paragraph known to the workers concerned.
Article 194-6Work Using a Jack-type Lifting Machine
When carrying out the work of lifting, lowering, etc., of load using a jack-type lifting machine in carrying out construction work, the employer must take the following measures:
事業者は、建設工事の作業を行う場合において、ジャッキ式つり上げ機械を用いて荷のつり上げ、つり下げ等の作業を行うときは、次の措置を講じなければならない。
to prohibit persons other than persons engaged in work concerned from entering the area where the work is carried out, by indicating the prohibition in a conspicuous place or by other methods;
当該作業を行う区域内に関係する作業従事者以外の者が立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止すること。
to suspend the work when dangers involved in carrying out the work are expected due to bad weather conditions such as strong wind, heavy rain or heavy snow;
強風、大雨、大雪等の悪天候のため、作業の実施について危険が予想されるときは、当該作業を中止すること。
when installing a jack-type lifting machine in facilities and temporary buildings etc., to fasten the machine securely using bolts, etc.; and
ジャッキ式つり上げ機械を施設、仮設物等に据え付けるときは、ボルト等を用いて当該ジャッキ式つり上げ機械を確実に固定させること。
when installing a jack-type lifting machine in facilities and temporary buildings, etc., to confirm the strength of the facilities and temporary buildings, etc., and to reinforce the strength when it is insufficient.
ジャッキ式つり上げ機械を施設、仮設物等に据え付けるときは、当該施設、仮設物等の耐力を確認し、耐力が不足しているときは、これを補強すること。
Article 194-7Wearing of Safety Helmets
When the work of lifting and lowering of load is carried out using a jack-type lifting machine in carrying out construction work, the employer must have the worker engaging in the work wear a safety helmet in order to prevent workers from dangers due to objects that come flying or falling.
事業者は、建設工事の作業を行う場合において、ジャッキ式つり上げ機械を用いて荷のつり上げ、つり下げ等の作業を行うときは、物体の飛来又は落下による労働者の危険を防止するため、当該作業に従事する労働者に保護帽を着用させなければならない。
The worker engaged in the work set forth in the preceding paragraph must wear the safety helmet set forth in the same paragraph.
第二節の三 高所作業車
Section 2-3 Vehicle for Work at Height
Article 194-8Front and Rear Lamps
As regards a vehicle for work at height (excluding those used for traveling; hereinafter the same applies in this Article) the employer must provide front and rear lamps for the vehicle; provided, however, that this does not apply to a vehicle for work at height used in the place where necessary illumination for safely carrying out the work is maintained.
Article 194-9Work Plan
When carrying out the work using a vehicle for work at height (excluding the work of traveling on roads; hereinafter the same applies up to Article 194-11), the employer must establish in advance a work plan in conformity with the situation of the place pertaining to the work, the type and capability of the vehicle, and carry out the work according to the work plan.
The work plan set forth in the preceding paragraph must indicate the work method using the vehicle for work at height.
When having established the work plan set forth in paragraph (1), the employer must make the matters indicated pursuant to the provisions of the preceding paragraph known to the workers concerned.
Article 194-10Work Director
When carrying out the work using a vehicle for work at height, the employer must designate a supervisor for the work, and have the supervisor direct the work based on the work plan set forth in paragraph (1) of the preceding Article.
Article 194-11Prevention of Falling
When carrying out the work using a vehicle for work at height, the employer must take necessary measures of projecting an outrigger, preventing uneven settling of the ground, and collapsing of a road shoulder in order to prevent workers from dangers due to overturning or falling of the vehicle.
事業者は、高所作業車を用いて作業を行うときは、高所作業車の転倒又は転落による労働者の危険を防止するため、アウトリガーを張り出すこと、地盤の不同沈下を防止すること、路肩の崩壊を防止すること等必要な措置を講じなければならない。
Article 194-12Signals
When carrying out the work using a vehicle for work at height and operating a working floor at a place other than the working floor, the employer must take necessary measures of setting fixed signals, designating a person who gives the signals and having the person give the signals, etc., in order to ensure the communication between the worker on the working floor and the worker operating the working floor at a place other than the working floor.
事業者は、高所作業車を用いて作業を行う場合で、作業床以外の箇所で作業床を操作するときは、作業床上の労働者と作業床以外の箇所で作業床を操作する者との間の連絡を確実にするため、一定の合図を定め、当該合図を行う者を指名してその者に行わせる等必要な措置を講じなければならない。
略称規定第十六条第二項
事業者は、令第六条第十七号の作業のうち、圧縮水素、圧縮天然ガス又は液化天然ガスを燃料とする自動車(道路運送車両法(昭和二十六年法律第百八十五号)に規定する普通自動車、小型自動車又は軽自動車(同法第五十八条第一項に規定する検査対象外軽自動車…
わかりやすく言うと
人や物品を運ぶかどうかにかかわらず、自動車などをその装置の使い方に従って用いることです。道路以外の場所だけで用いることは含みません(道路運送車両法第二条第五項)。
略称規定第二十四条の三第一項
法第二十五条の二第一項に規定する事業者(以下この章において「事業者」という。)は、次の各号に掲げる機械、器具その他の設備(以下「機械等」という。)を備え付けなければならない。
わかりやすく言うと
機械、器具その他の設備をまとめた呼び名です。この条では、爆発や火災などの際の作業従事者の救護に備えて事業者が備え付ける、空気呼吸器又は酸素呼吸器、ガスの濃度の測定器具、携帯用照明器具などを指します。
略称規定第二十四条の十三第一項
労働者に危険を及ぼし、又は労働者の健康障害をその使用により生ずるおそれのある機械(以下単に「機械」という。)を譲渡し、又は貸与する者(次項において「機械譲渡者等」という。)は、文書の交付等により当該機械に関する次に掲げる事項を…
わかりやすく言うと
使うことによって労働者に危険を及ぼし、又は労働者の健康障害を生ずるおそれのある機械のことです。
定義第三十六条第一項第十号の四
複数の保持機構(ワイヤロープ等を締め付けること等によつて保持する機構をいう。以下同じ。)を有し、当該保持機構を交互に開閉し、保持機構間を動力を用いて伸縮させることにより荷のつり上げ、つり下げ等の作業をワイヤロープ等を介して行う機械
わかりやすく言うと
ワイヤロープなどを締め付けることなどで保持する保持機構を複数持ち、それを交互に開閉しながら保持機構の間を動力で伸び縮みさせて、ワイヤロープなどを介して荷のつり上げやつり下げなどを行う機械です。
定義第三十六条第一項第十号の五
令第十条第七号の高所作業車
わかりやすく言うと
作業床の高さ(作業床を最も高く上げたときの床面の高さ)が二メートル以上の高所作業車のことです(労働安全衛生法施行令第十条第七号)。
略称規定第百七十三条第一項
事業者は、動力を用いるくい打機(以下「くい打機」という。)、動力を用いるくい抜機(以下「くい抜機」という。)又はボーリングマシンについては、倒壊を防止するため、次の措置を講じなければならない。
略称規定第百七十三条第一項
事業者は、動力を用いるくい打機(以下「くい打機」という。)、動力を用いるくい抜機(以下「くい抜機」という。)又はボーリングマシンについては、倒壊を防止するため、次の措置を講じなければならない。
略称規定第百九十四条第一項・この条の中だけ
事業者は、くい打機又はボーリングマシンを使用して作業を行う場合において、ガス導管、地中電線路その他地下に存する工作物(以下この条において「ガス導管等」という。)の損壊により労働者に危険を及ぼすおそれのあるときは、あらかじめ…
わかりやすく言うと
ガス導管、地中電線路その他の地下にある工作物をまとめた呼び名で、この条だけで使われます。