Search

Search provisions, jump to a law or an article

7 articles

Article 314Appointment of Operations Supervisor of Gas Welding

第三百十四条(ガス溶接作業主任者の選任)

As regards the work set forth in Article 6, item (ii) of the Order, the employer must appoint operations supervisor of gas welding from persons who have the license of operations supervisor of gas welding.

事業者は、令第六条第二号の作業については、ガス溶接作業主任者免許を有する者のうちから、ガス溶接作業主任者を選任しなければならない。

Article 315Duties of an Operations Supervisor of Gas Welding

第三百十五条(ガス溶接作業主任者の職務)

When carrying out work of welding, fusing or heating metal using an acetylene welding equipment, the employer must have the operations supervisor of gas welding carry out the following matters:

事業者は、アセチレン溶接装置を用いて金属の溶接、溶断又は加熱の作業を行なうときは、ガス溶接作業主任者に、次の事項を行なわせなければならない。

to decide the work method, and supervise the work;

作業の方法を決定し、作業を指揮すること。

to have the worker engaging in handling acetylene welding equipment carry out the following matters:

アセチレン溶接装置の取扱いに従事する労働者に次の事項を行なわせること。

to not use a tool which is likely to produce sparks for, or give shocks to, the generator being used;

使用中の発生器に、火花を発するおそれのある工具を使用し、又は衝撃を与えないこと。

when inspecting gas leakage from acetylene welding equipment, to use a safe method such as using soap water;

アセチレン溶接装置のガス漏れを点検するときは、石けん水を使用する等安全な方法によること。

to not put things on the gas bell of the generator without reason;

発生器の気鐘の上にみだりに物を置かないこと。

to not leave the door of the entrance to the generator room open;

発生器室の出入口の戸を開放しておかないこと。

when recharging carbide to the generator of portable acetylene welding equipment, to carry out the operations at a safe place outdoors; and

移動式のアセチレン溶接装置の発生器にカーバイドを詰め替えるときは、屋外の安全な場所で行なうこと。

when opening a carbide can, to not perform acts that are likely to produce sparks, such as giving shocks;

カーバイド罐を開封するときは、衝撃その他火花を発するおそれのある行為をしないこと。

when starting the work, to inspect the acetylene welding equipment, and when a mixed gas of air and acetylene exists in the generator, to remove the mixed gas;

当該作業を開始するときは、アセチレン溶接装置を点検し、かつ、発生器内に空気とアセチレンの混合ガスが存在するときは、これを排除すること。

to place the safety equipment at a place where its water-level can easily be inspected during operations, and inspect the safety device more than once a day;

安全器は、作業中、その水位を容易に確かめることができる箇所に置き、かつ、一日一回以上これを点検すること。

when keeping the acetylene welding equipment warm or heating the equipment to prevent water in the equipment from freezing, to use a safe method, such as using warm water or steam;

アセチレン溶接装置内の水の凍結を防ぐために、保温し、又は加温するときは、温水又は蒸気を使用する等安全な方法によること。

when suspending the use of the generator, to keep the water level in its water chamber in a condition that the water and residual carbide may not come into contact each other;

発生器の使用を休止するときは、その水室の水位を水と残留カーバイドが接触しない状態に保つこと。

when repairing, processing, transporting or storing the generator, or suspending its use continuously, to completely remove the acetylene and carbide from the generator;

発生器の修繕、加工、運搬若しくは格納をしようとするとき、又はその使用を継続して休止しようとするときは、アセチレン及びカーバイドを完全に除去すること。

to dispose carbide sludge in a safe manner such as keeping it in a sludge pit until the danger due to gas is removed;

カーバイドのかすは、ガスによる危険がなくなるまでかすだめに入れる等安全に処置すること。

to monitor the use of eye protector and protective gloves by workers engaged in the work; and

当該作業に従事する労働者の保護眼鏡及び保護手袋の使用状況を監視すること。

to carry the license of operations supervisor of gas welding.

ガス溶接作業主任者免許証を携帯すること。

Article 316

第三百十六条

When carrying out the work of welding, fusing or heating metal using the gas welding equipment using manifolds, the employer must have the operations supervisor of gas welding carry out the following matters:

事業者は、ガス集合溶接装置を用いて金属の溶接、溶断又は加熱の作業を行なうときは、ガス溶接作業主任者に次の事項を行なわせなければならない。

to decide the work method and supervise the work;

作業の方法を決定し、作業を指揮すること。

to have the worker engaging in the handling of the gas manifolds carry out the following matters:

ガス集合装置の取扱いに従事する労働者に次の事項を行なわせること。

to remove oil, etc., and dust, etc., adhering to the mouthpiece of the gas cylinder and the mounting opening of the piping;

取り付けるガスの容器の口金及び配管の取付け口に付着している油類、じんあい等を除去すること。

when having exchanged gas cylinders, to inspect the mouthpiece of the gas cylinder and the mounting opening of the piping for leakage of gas, and remove the mixed gas of the gas and air in the piping;

ガスの容器の取替えを行なつたときは、当該容器の口金及び配管の取付け口の部分のガス漏れを点検し、かつ、配管内の当該ガスと空気との混合ガスを排除すること。

when inspecting leakage of gas, to use a safe method such as using soap water;

ガス漏れを点検するときは、石けん水を使用する等安全な方法によること。

to open and close the valve or cock gently;

バルブ又はコツクの開閉を静かに行なうこと。

to be present when the gas cylinders are exchanged;

ガスの容器の取替えの作業に立ち合うこと。

when commencing the work, to inspect the hose, blowpipe, hose band, etc., and when having found that there is a risk of leakage of gas or oxygen due to the damage, wear, etc., to repair or exchange the parts damaged, worn, etc.;

当該作業を開始するときは、ホース、吹管、ホースバンド等の器具を点検し、損傷、摩耗等によりガス又は酸素が漏えいするおそれがあると認めたときは、補修し、又は取り替えること。

to place the safety equipment at a place where its functions can easily be confirmed, and inspect the safety device more than once a day;

安全器は、作業中、その機能を容易に確かめることができる箇所に置き、かつ、一日一回以上これを点検すること。

to monitor the use of eye protector and protective gloves by workers engaged in the work; and

当該作業に従事する労働者の保護眼鏡及び保護手袋の使用状況を監視すること。

to carry the license of operations supervisor of gas welding.

ガス溶接作業主任者免許証を携帯すること。

Article 317Periodical Self-inspection

第三百十七条(定期自主検査)

As regards an acetylene welding equipment or a gas welding equipment using manifolds (excluding the parts of the piping of those devices installed underground; hereinafter the same applies in this Article), the employer must carry out a self-inspection on the existence of damage, deformation, corrosion, etc., and the functions of the equipment periodically once every period not exceeding one year; provided, however, that this does not apply to the non-use period of acetylene welding equipment or a gas welding equipment using manifolds, which is not used for a period exceeding one year.

事業者は、アセチレン溶接装置又はガス集合溶接装置(これらの配管のうち、地下に埋設された部分を除く。以下この条において同じ。)については、一年以内ごとに一回、定期に、当該装置の損傷、変形、腐食等の有無及びその機能について自主検査を行なわなければならない。ただし、一年をこえる期間使用しないアセチレン溶接装置又はガス集合溶接装置の当該使用しない期間においては、この限りでない。

As regards the acetylene welding equipment or gas welding equipment using manifolds referred to in the proviso of the preceding paragraph, the employer must carry out a self-inspection for the matters prescribed in the same paragraph before resuming the operation.

事業者は、前項ただし書のアセチレン溶接装置又はガス集合溶接装置については、その使用を再び開始する際に、同項に規定する事項について自主検査を行なわなければならない。

When an abnormality is found in the acetylene welding equipment or gas welding equipment using manifolds as a result of the self-inspection referred to in the preceding two paragraphs, the employer must not use the equipment unless repairs are made or other necessary measures have been taken.

事業者は、前二項の自主検査の結果、当該アセチレン溶接装置又はガス集合溶接装置に異常を認めたときは、補修その他必要な措置を講じた後でなければ、これらを使用してはならない。

When having carried out the self-inspection set forth in paragraph (1) or (2), the employer must record the following matters and preserve the record for three years:

事業者は、第一項又は第二項の自主検査を行つたときは、次の事項を記録し、これを三年間保存しなければならない。

the date of the inspection;

検査年月日

the method of the inspection;

検査方法

the parts inspected;

検査箇所

the results of the inspection;

検査の結果

the name of the person who has carried out the inspection; and

検査を実施した者の氏名

when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.

検査の結果に基づいて補修等の措置を講じたときは、その内容

Section 7 Blasting Work

第七節 発破の作業

Article 318Standards of Blasting Work

第三百十八条(発破の作業の基準)

The employer must have the worker engaging in the work set forth in Article 20, item (i) of the Order (hereinafter referred to as "blasting work") carry out the following matters:

事業者は、令第二十条第一号の業務(以下「発破の業務」という。)に従事する労働者に次の事項を行わせなければならない。

to not defreeze the frozen dynamite by a dangerous method, such as bringing it in proximity to fire or into direct contact with a steam pipe or other high-temperature objects;

凍結したダイナマイトは、火気に接近させ、蒸気管その他の高熱物に直接接触させる等危険な方法で融解しないこと。

when charging gunpowder or explosives, to not use naked fire or smoke in the vicinity;

火薬又は爆薬を装塡するときは、その付近で裸火の使用又は喫煙をしないこと。

to use a safe charging tool, which are unlikely to cause an explosion due to friction, shock, static electricity, etc.;

装塡具は、摩擦、衝撃、静電気等による爆発を生ずるおそれのない安全なものを使用すること。

to use a safe stemming, which are unlikely to cause an ignition or an inflammation, such as clay or sand;

込物は、粘土、砂その他の発火又は引火の危険のないものを使用すること。

when the charged gunpowder does not explode after ignition, or when it is difficult to confirm that the charged gunpowder has exploded, to comply with the requirements set forth in the following sub-items:

点火後、装塡された火薬類が爆発しないとき、又は装塡された火薬類が爆発したことの確認が困難であるときは、次に定めるところによること。

when an electric detonator is used, to remove the blasting leading wire from the igniter and short-circuit the end of the wire, and take measures to prevent re-ignition; and not to approach the place where the gunpowder is charged within five minutes after the measures are taken; and

電気雷管によつたときは、発破母線を点火器から取り外し、その端を短絡させておき、かつ、再点火できないように措置を講じ、その後五分以上経過した後でなければ、火薬類の装塡箇所に接近しないこと。

when device other than an electric detonator is used, not to approach the place where the gunpowder is charged within 15 minutes after ignition.

電気雷管以外のものによつたときは、点火後十五分以上経過した後でなければ、火薬類の装塡箇所に接近しないこと。

The worker engaging in the work set forth in the preceding paragraph must carry out the matters listed in each item of the same paragraph.

前項の業務に従事する労働者は、同項各号に掲げる事項を行なわなければならない。

When charging gunpowder or explosives, the employer must prohibit the use of naked fire or smoking in the vicinity by persons engaged in work (excluding workers) who engage in blasting work, by indicating the prohibition in a conspicuous place or by other methods.

事業者は、火薬又は爆薬を装塡するときは、その付近で発破の業務に従事する作業従事者(労働者を除く。)の裸火の使用又は喫煙について、禁止する旨を見やすい箇所に表示することその他の方法により禁止しなければならない。

A person engaged in work (excluding a worker) who engages in the blasting work referred to in the preceding paragraph must not use naked fire or smoke in the vicinity where gunpowder or explosives are being charged.

前項の発破の業務に従事する作業従事者(労働者を除く。)は、火薬又は爆薬の装塡が行われる付近で裸火の使用又は喫煙をしてはならない。

Article 319Supervisor for Fuse Blasting Work

第三百十九条(導火線発破作業の指揮者)

When carrying out fuse blasting work, the employer must appoint a supervisor from those eligible for the work, and have the supervisor carry out the following matters:

事業者は、導火線発破の作業を行なうときは、発破の業務につくことができる者のうちから作業の指揮者を定め、その者に次の事項を行なわせなければならない。

to instruct workers other than those engaging in igniting work to evacuate the workplace before ignition;

点火前に、点火作業に従事する労働者以外の労働者に対して、退避を指示すること。

to indicate the place for evacuation and the route to that place to workers engaging in the igniting work;

点火作業に従事する労働者に対して、退避の場所及び経路を指示すること。

when a worker takes charge of five or more ignitions at a time, have each worker use device that notifies the time of evacuation such as a blasting watch or waste fuses;

一人の点火数が同時に五以上のときは、発破時計、捨て導火線等の退避時期を知らせる物を使用すること。

to instruct workers on the procedures and specification of the igniting work;

点火の順序及び区分について指示すること。

to give a signal of ignition;

点火の合図をすること。

to give a signal of evacuation to workers who engaged in the igniting work; and

点火作業に従事した労働者に対して、退避の合図をすること。

to check for misfires or residual gunpowder.

不発の装薬又は残薬の有無について点検すること。

The supervisor for fuse blasting work must carry out the matters listed in each item of the preceding paragraph.

導火線発破の作業の指揮者は、前項各号に掲げる事項を行なわなければならない。

The worker who engages in the fuse blasting work must follow the instructions and signals given by the supervisor pursuant to the provisions of the preceding paragraph.

導火線発破の作業に従事する労働者は、前項の規定により指揮者が行なう指示及び合図に従わなければならない。

Article 320Supervisor for Electric Blasting Work

第三百二十条(電気発破作業の指揮者)

When carrying out electric blasting work, the employer must appoint a supervisor from those eligible for the work and have the supervisor carry out the matters set forth in paragraph (1), items (v) and (vii) of the preceding Article and the following matters:

事業者は、電気発破の作業を行なうときは、発破の業務につくことができる者のうちから作業の指揮者を定め、その者に前条第一項第五号及び第七号並びに次の事項を行なわせなければならない。

to indicate the place for evacuation and the route to that place to the workers engaging in the work;

当該作業に従事する労働者に対し、退避の場所及び経路を指示すること。

to confirm that workers have been evacuated from the dangerous area before ignition;

点火前に危険区域内から労働者が退避したことを確認すること。

to appoint a person in charge of the ignition; and

点火者を定めること。

to give instruction on the place of ignition.

点火場所について指示すること。

The supervisor of the electric blasting work must carry out the matters listed in each item of the preceding paragraph.

電気発破の作業の指揮者は、前項各号に掲げる事項を行なわなければならない。

The worker engaging in the electric blasting work must follow the instructions and signals given by the supervisor pursuant to the provisions of the preceding paragraph.

電気発破の作業に従事する労働者は、前項の規定により指揮者が行なう指示及び合図に従わなければならない。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy