The value of allowable stress of materials set forth in paragraph (3), item (i) of the preceding Article is to comply with the following requirements:
前条第三項第一号の材料の許容応力の値は、次に定めるところによる。
the value of allowable bending stress and allowable compressive stress of steel materials are to be two thirds or less of the value of the yield strength of the steel materials or three quarters of the value of the tensile strength, whichever is smaller;
鋼材の許容曲げ応力及び許容圧縮応力の値は、当該鋼材の降伏強さの値又は引張強さの値の四分の三の値のうちいずれか小さい値の三分の二の値以下とすること。
the value of allowable shearing stress of steel materials is to be 38 % or less of the yield strength of the steel materials or three quarters of the value of the tensile strength, whichever is smaller; and
鋼材の許容せん断応力の値は、当該鋼材の降伏強さの値又は引張強さの値の四分の三の値のうちいずれか小さい値の百分の三十八の値以下とすること。
the value of allowable buckling stress of steel materials is to be equal to or less than the value obtained by the calculation using the following formula:
鋼材の許容座屈応力の値は、次の式により計算を行つて得た値以下とすること。
When l/i ≦ Λ
l/i≦Λの場合
бc = ((1 - 0.4((l/i)/Λ)^2)/ν)F
бc=((1-0.4((l/i)/Λ)2)/ν)F
When l/i > Λ
l/i>Λの場合
бc = (0.29/((l/i)/Λ)^2)F
| (In these formulas, l, i, Λ, бc, ν and F represent the following values, respectively. l: Length of the support (where the support is restrained from displacement in the horizontal direction, the maximum length among the lengths between the restraining points) (unit: cm) i: Minimum radius of gyration of area of the support (unit: cm) Λ: Critical slenderness ratio = √(π^2E/0.6F) However, π: Circular constant E: Young's modulus of the steel material (unit: N/cm2) бc: Value of allowable buckling stress (unit: N/cm2) ν: Safety factor = 1.5 + 0.57((l/i)/Λ)^2 F: The smaller of the value of the yield strength of the steel material or three quarters of the value of the tensile strength (unit: N/cm2)) |
бc=(0.29/((l/i)/Λ)2)F
| (これらの式において、l、i、Λ、бc、ν及びFは、それぞれ次の値を表すものとする。 l 支柱の長さ(支柱が水平方向の変位を拘束されているときは、拘束点間の長さのうちの最大の長さ)(単位 センチメートル) i 支柱の最小断面二次半径(単位 センチメートル) Λ 限界細長比=√(π2E/0.6F) ただし、π 円周率 E 当該鋼材のヤング係数(単位 ニュートン毎平方センチメートル) бc 許容座屈応力の値(単位 ニュートン毎平方センチメートル) ν 安全率=1.5+0.57((l/i)/Λ)2 F 当該鋼材の降伏強さの値又は引張強さの値の四分の三の値のうちのいずれか小さい値(単位 ニュートン毎平方センチメートル)) |
the value of allowable bending stress, allowable compressive stress and allowable shearing stress of timber in the direction of fiber are to be equal to or less than the value listed in the right column of the following Table in accordance with the kind of timber listed in the left column of the same Table.
| Type of timber | Value of Allowable Stress (Unit: N/cm2) | ||
| Bending | Compression | Shearing | |
| Japanese red pine, Japanese black pine, Japanese larch, hiba, hinoki, Japanese hemlock, Oregon pine, or Port Oxford cedar | 1,320 | 1,180 | 103 |
| Japanese cedar, fir, silver fir, abies, red cedar or Western hemlock | 1,030 | 880 | 74 |
| Oak | 1,910 | 1,320 | 210 |
| Japanese chestnut, Japanese oak, Japanese beech, or keyaki | 1,470 | 1,030 | 150 |
木材の繊維方向の許容曲げ応力、許容圧縮応力及び許容せん断応力の値は、次の表の上欄に掲げる木材の種類に応じ、それぞれ同表の下欄に掲げる値以下とすること。
| 木材の種類 | 許容応力の値(単位 ニュートン毎平方センチメートル) | ||
| 曲げ | 圧縮 | せん断 | |
| あかまつ、くろまつ、からまつ、ひば、ひのき、つが、べいまつ又はべいひ | 一、三二〇 | 一、一八〇 | 一〇三 |
| すぎ、もみ、えぞまつ、とどまつ、べいすぎ又はべいつが | 一、〇三〇 | 八八〇 | 七四 |
| かし | 一、九一〇 | 一、三二〇 | 二一〇 |
| くり、なら、ぶな又はけやき | 一、四七〇 | 一、〇三〇 | 一五〇 |
the value of allowable buckling stress of timber in the direction of fiber is to be equal to or less than the value obtained by calculation using the following formula:
木材の繊維方向の許容座屈応力の値は、次の式により計算を行つて得た値以下とすること。
When lk/i ≦100; fk = fc(1 - 0.007(lk/i))
lk/i≦100の場合 fk=fc(1-0.007(lk/i))
When lk/i > 100: fk = 0.3fc/(lk/100i)^2
| (In these formulas, lk, i, fc and fk represent the following values, respectively. lk: Length of the support (where the support is restrained from displacement in the horizontal direction, the maximum length among the lengths between the restraining points) (unit: cm) i: Minimum radius of gyration of area of the support (unit: cm) fc: Value of allowable compressive stress (unit: N/cm2) fk: Value of allowable buckling stress (unit: N/cm2)) |
lk/i>100の場合 fk=0.3fc/(lk/100i)2
| (これらの式において、lk、i、fc及びfkは、それぞれ次の値を表すものとする。 lk 支柱の長さ(支柱が水平方向の変位を拘束されているときは、拘束点間の長さのうち最大の長さ)(単位 センチメートル) i 支柱の最小断面二次半径(単位 センチメートル) fc 許容圧縮応力の値(単位 ニュートン毎平方センチメートル) fk 許容座屈応力の値(単位 ニュートン毎平方センチメートル)) |