第百六十五条(修理等)
When carrying out the work of repairing a vehicle type construction machine, or fitting or removing its attachments, the employer must designate a person to direct the work and have that person take the following measures:
事業者は、車両系建設機械の修理又はアタツチメントの装着若しくは取り外しの作業を行うときは、当該作業を指揮する者を定め、その者に次の措置を講じさせなければならない。
to decide the work procedures, and supervise the work;
作業手順を決定し、作業を指揮すること。
to monitor the state of use of a safety prop, a safety block, etc., prescribed in paragraph (1) of the following Article and a stand prescribed in Article 166-2, paragraph (1).
次条第一項に規定する安全支柱、安全ブロツク等及び第百六十六条の二第一項に規定する架台の使用状況を監視すること。
Article 166Prevention of Dangers Due to Lowering of Booms
第百六十六条(ブーム等の降下による危険の防止)
When carrying out the work of repairing, checking, etc., below the raised boom or arm, etc., of a vehicle type construction machine, the employer must have the worker engaging in the work use a safety prop, a safety block, etc., in order to prevent workers from dangers due to unexpected descending of the boom or the arm, etc.
事業者は、車両系建設機械のブーム、アーム等を上げ、その下で修理、点検等の作業を行うときは、ブーム、アーム等が不意に降下することによる労働者の危険を防止するため、当該作業に従事する労働者に安全支柱、安全ブロツク等を使用させなければならない。
The worker engaging in the work set forth in the preceding paragraph must use the safety prop, safety block, etc., set forth in the same paragraph.
Article 166-2Prevention of Dangers Due to Collapse of Attachments, etc.
第百六十六条の二(アタツチメントの倒壊等による危険の防止)
When carrying out the work of fitting or removing an attachment of a vehicle type construction machine, the employer must have the workers engaging in the work use a stand in order to prevent workers from dangers due to collapse of the attachment, etc.
事業者は、車両系建設機械のアタツチメントの装着又は取り外しの作業を行うときはアタツチメントが倒壊すること等による労働者の危険を防止するため、当該作業に従事する労働者に架台を使用させなければならない。
The worker engaging in the work set forth in the preceding paragraph must use the stand set forth in the same paragraph.
Article 166-3Restriction on Fitting of Attachments
第百六十六条の三(アタツチメントの装着の制限)
The employer must not fit to a vehicle type construction machine an attachment exceeding the weight decided on the basis of its structure.
事業者は、車両系建設機械にその構造上定められた重量を超えるアタツチメントを装着してはならない。
Article 166-4Indication of Weight of Attachments, etc.
第百六十六条の四(アタツチメントの重量の表示等)
When the employer has replaced an attachment of a vehicle type construction machine, the employer must display the weight of the attachment (including, where a bucket, ripper, etc. is fitted, the capacity or maximum loading weight of that bucket, ripper, etc.; the same applies hereinafter in this Article) in a position easily visible to the operator, or keep on the vehicle type construction machine a document from which the operator can easily confirm the weight of the attachment.
事業者は、車両系建設機械のアタツチメントを取り替えたときは、運転者の見やすい位置にアタツチメントの重量(バケツト、ジツパー等を装着したときは、当該バケツト、ジツパー等の容量又は最大積載重量を含む。以下この条において同じ。)を表示し、又は当該車両系建設機械に運転者がアタツチメントの重量を容易に確認できる書面を備え付けなければならない。
Subsection 3 Periodical Self-inspection
第三款 定期自主検査等
Article 167Periodical Self-inspection
第百六十七条(定期自主検査)
As regards a vehicle type construction machine, the employer must carry out a self-inspection for the following matters periodically once every period not exceeding one year; provided, however, that this does not apply to the non-use period of a vehicle type construction machine which is not used for a period exceeding one year:
事業者は、車両系建設機械については、一年以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一年を超える期間使用しない車両系建設機械の当該使用しない期間においては、この限りでない。
abnormalities in compression pressure, valve clearance and other abnormalities of the prime mover;
圧縮圧力、弁すき間その他原動機の異常の有無
abnormalities in the clutch, transmission, propeller shaft, differential, and other abnormalities of power transmission devices;
クラツチ、トランスミツシヨン、プロペラシヤフト、デフアレンシヤルその他動力伝達装置の異常の有無
abnormalities in the drive wheel, idling wheel, vertical trunk roller, belt, tire, wheel bearing, and other abnormalities of traveling devices;
起動輪、遊動輪、上下転輪、履帯、タイヤ、ホイールベアリングその他走行装置の異常の有無
abnormalities in rotation angle of left and right steering wheels, knuckle, rod, arm and other abnormalities of controlling devices;
かじ取り車輪の左右の回転角度、ナツクル、ロツド、アームその他操縦装置の異常の有無
abnormalities in braking capability, brake drum, brake shoe and other abnormalities of brakes;
制動能力、ブレーキドラム、ブレーキシユーその他ブレーキの異常の有無
abnormalities in blade, boom, link-mechanism, bucket, wire rope and other abnormalities of working devices;
ブレード、ブーム、リンク機構、バケツト、ワイヤロープその他作業装置の異常の有無
abnormalities in hydraulic pump, hydraulic motor, cylinder, safety valve and other abnormalities of the hydraulic system;
油圧ポンプ、油圧モーター、シリンダー、安全弁その他油圧装置の異常の有無
abnormalities in voltage, amperage and other abnormalities of the electrical system; and
電圧、電流その他電気系統の異常の有無
abnormalities in the body, operating device, head guard, back stopper, raising and lowering device, locking device, warning device, direction indicator, lighting device and meter.
車体、操作装置、ヘツドガード、バツクストツパー、昇降装置、ロツク装置、警報装置、方向指示器、灯火装置及び計器の異常の有無
As regards the vehicle type construction machine set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.
第百六十八条
As regards a vehicle type construction machine, the employer must carry out a self-inspection for the following matters periodically once every period not exceeding one month; provided, however, that this does not apply to the non-use period of a vehicle type construction machine which is not used for a period exceeding one month:
事業者は、車両系建設機械については、一月以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一月を超える期間使用しない車両系建設機械の当該使用しない期間においては、この限りでない。
abnormalities in brake, clutch, controlling devices and working devices;
ブレーキ、クラツチ、操作装置及び作業装置の異常の有無
damage in wire rope and chain;
ワイヤロープ及びチエーンの損傷の有無
damage in bucket, ripper, etc.; and
バケツト、ジツパー等の損傷の有無
in the case of the specified demolition machine set forth in Article 171-4, abnormalities in the check valve, warning device, etc.
第百七十一条の四の特定解体用機械にあつては、逆止め弁、警報装置等の異常の有無
As regards the vehicle type construction machine set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.
Article 169Record of Periodical Self-inspections
第百六十九条(定期自主検査の記録)
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
When having carried out the self-inspection set forth in the preceding two Articles, the employer must record the following matters and preserve the record for three years:
事業者は、前二条の自主検査を行つたときは、次の事項を記録し、これを三年間保存しなければならない。
the date of the inspection;
検査年月日
the method of the inspection;
検査方法
the parts inspected;
検査箇所
the results of the inspection;
検査の結果
the name of the person who has carried out the inspection; and
検査を実施した者の氏名
when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.
検査の結果に基づいて補修等の措置を講じたときは、その内容
Article 169-2Specified Self-inspection
第百六十九条の二(特定自主検査)
The specified inspection pertaining to the vehicle type construction machine is to be the self-inspection prescribed in Article 167.
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
The provisions of Article 151-24, paragraph (2) apply mutatis mutandis to a person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to machines listed in Appended Table 7, item (i), item (ii) or item (vi) of the Order among vehicle type construction machines. In this case, the term "forklift" in Article 151-24, paragraph (2), item (i), (a) through (c) is deemed to be replaced with "machines listed in Appended Table 7, item (i), item (ii) or item (vi) of the Order among vehicle type construction machines" and the term "forklift" in (d) of the same item is deemed to be replaced with "machines listed in Appended Table 7, item (i), item (ii) or item (vi) of the Order among vehicle type construction machines."
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
The provisions of Article 151-24, paragraph (2) apply mutatis mutandis to a person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to machines listed in Appended Table 7, item (iii) of the Order among vehicle type construction machines. In this case, the term "forklift" in Article 151-24, paragraph (2), item (i) is deemed to be replaced with "machines listed in Appended Table 7, item (iii) of the Order among vehicle type construction machines."
第百五十一条の二十四第二項の規定は、車両系建設機械のうち令別表第七第三号に掲げるものに係る法第四十五条第二項の厚生労働省令で定める資格を有するものについて準用する。この場合において、第百五十一条の二十四第二項第一号中「フォークリフト」とあるのは、「車両系建設機械のうち令別表第七第三号に掲げるもの」と読み替えるものとする。
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
The provisions of Article 151-24, paragraph (2) apply mutatis mutandis to a person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to machines listed in Appended Table 7, item (iv) of the Order among vehicle type construction machines. In this case, the term "forklift" in Article 151-24, paragraph (2), item (i) is deemed to be replaced with "machines listed in Appended Table 7, item (iv) of the Order among vehicle type construction machines."
第百五十一条の二十四第二項の規定は、車両系建設機械のうち令別表第七第四号に掲げるものに係る法第四十五条第二項の厚生労働省令で定める資格を有するものについて準用する。この場合において、第百五十一条の二十四第二項第一号中「フォークリフト」とあるのは、「車両系建設機械のうち令別表第七第四号に掲げるもの」と読み替えるものとする。
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
The provisions of Article 151-24, paragraph (2) apply mutatis mutandis to a person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to machines listed in Appended Table 7, item (v) of the Order among vehicle type construction machines. In this case, the term "forklift" in Article 151-24, paragraph (2), item (i) is deemed to be replaced with "machines listed in Appended Table 7, item (v) of the Order among vehicle type construction machines."
第百五十一条の二十四第二項の規定は、車両系建設機械のうち令別表第七第五号に掲げるものに係る法第四十五条第二項の厚生労働省令で定める資格を有するものについて準用する。この場合において、第百五十一条の二十四第二項第一号中「フォークリフト」とあるのは、「車両系建設機械のうち令別表第七第五号に掲げるもの」と読み替えるものとする。
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
As regards the vehicle type construction machine used for traveling (limited to the machine to which Article 48, paragraph (1) of the Road Transport Vehicle Act applies), when an inspection pursuant to the provisions of the same paragraph has been carried out, the employer is not required to carry out the self-inspection set forth in Article 167 for the parts where the inspection has been carried out.
事業者は、運行の用に供する車両系建設機械(道路運送車両法第四十八条第一項の適用を受けるものに限る。)について、同項の規定に基づいて点検を行つた場合には、当該点検を行つた部分については第百六十七条の自主検査を行うことを要しない。
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
As regards the application of the provisions of the preceding Article when having a registered inspection agency conduct the specified inspection pertaining to a vehicle type construction machine, the term "the name of the person who has carried out the inspection" in item (v) of the same Article is deemed to be replaced with "the name of the registered inspection agency."
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
When having carried out the specified inspection pertaining to a vehicle type construction machine, the employer must affix an inspection sticker stating the month and year when the specified inspection was carried out at a readily visible part of the machine.
Article 170Inspection before Commencing Work
第百七十条(作業開始前点検)
When carrying out work using a vehicle type construction machine, the employer must inspect the functions of the brake and clutch before commencing the work for the day.
事業者は、車両系建設機械を用いて作業を行なうときは、その日の作業を開始する前に、ブレーキ及びクラツチの機能について点検を行なわなければならない。
第百七十一条(補修等)
Changes on (Ministry of Health, Labour and Welfare Order No. 29 of 2026)
When having found any abnormalities in carrying out the self-inspection set forth in Article 167 or Article 168, or the inspection set forth in the preceding Article, the employer must immediately make repairs or take other necessary measures.
Subsection 4 Concrete Pump Vehicle
第四款 コンクリートポンプ車
Article 171-2Prevention of Coming off or Sway of Transport Pipes
第百七十一条の二(輸送管等の脱落及び振れの防止等)
When carrying out the work using a concrete pump vehicle, the employer must take the following measures:
事業者は、コンクリートポンプ車を用いて作業を行うときは、次の措置を講じなければならない。
to take measures of preventing the coming off or sway of the transport pipe or hose such as securely attaching a transport pipe to a transport pipe or a hose using couplings, and securing the transport pipe onto a solid building, etc.;
輸送管を継手金具を用いて輸送管又はホースに確実に接続すること、輸送管を堅固な建設物に固定させること等当該輸送管及びホースの脱落及び振れを防止する措置を講ずること。
to provide devices of a telephone, an electric bell, etc., designate persons who use each device and have the persons use them, or set fixed signals, designate a person who gives the signals and have the person give the signals, in order to ensure the communication between the person operating the work device and the person holding the terminal of the hoses;
作業装置の操作を行う者とホースの先端部を保持する者との間の連絡を確実にするため、電話、電鈴等の装置を設け、又は一定の合図を定め、それぞれ当該装置を使用する者を指名してその者に使用させ、又は当該合図を行う者を指名してその者に行わせること。
to prohibit a person engaged in work at the workshop from entering a place where there is a risk of danger due to the blowing out of concrete, etc., by indicating the prohibition in a conspicuous place or by other methods;
当該作業場において作業に従事する作業従事者がコンクリート等の吹出しにより危険が生ずるおそれのある箇所に立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止すること。
when the transport pipe or hose is blocked, and seeking to cut off the coupling of the transport pipe or hose (hereinafter referred to as "transport pipe, etc." in this Article and the following Article), to take in advance measures for preventing blow out, etc., of concrete, such as lowering the internal pressure of the transport pipe, etc., by opening the valve or cock of the air compressor;
輸送管又はホースが閉そくした場合で、輸送管及びホース(以下この条及び次条において「輸送管等」という。)の接続部を切り離そうとするときは、あらかじめ、当該輸送管等の内部の圧力を減少させるため空気圧縮機のバルブ又はコックを開放すること等コンクリート等の吹出しを防止する措置を講ずること。
when cleaning the inside of the transport pipe, etc., using a cleaning ball, to attach an instrument to the end of the transport pipe, etc., in order to prevent workers from dangers due to the cleaning ball flying out.
洗浄ボールを用いて輸送管等の内部を洗浄する作業を行うときは、洗浄ボールの飛出しによる労働者の危険を防止するための器具を当該輸送管等の先端部に取り付けること。
operationmachine translation
「運行」
Using a road transport vehicle as its equipment is meant to be used, whether or not it carries people or goods, other than using it only off public roads, as Article 2, paragraph (5) of the Road Transport Vehicle Act defines it.
Short name set inArticle 16, paragraph (2)
person engaged in workmachine translation
「作業従事者」
A person who does the work of a job carried out by a person running a business (事業), whether or not that person is a worker (労働者) employed there.
Defined inArticle 18-5, paragraph (1)
vehicle type construction machine
「車両系建設機械」
A construction machine listed in Appended Table 7 of the Order for Enforcement of Industrial Safety and Health Act — machines for levelling, hauling and loading, digging, foundation work, compaction, concrete placing and demolition — that runs on power and can travel under its own power to any place.
Defined inArticle 94-2, paragraph (1), item (ii)
specified inspectioncorrected by this site
「特定自主検査」
For power presses, the annual periodic self-inspection of Article 134-3, which Article 45, paragraph (2) of the Industrial Safety and Health Act requires to be done by a qualified employer or worker, or by a registered inspection agency (検査業者).
Short name set inArticle 135-3, paragraph (1)
registered inspection agencymachine translation
「検査業者」
A person registered under Article 54-3, paragraph (1) of the Industrial Safety and Health Act who carries out specified self-inspections (特定自主検査) of machinery or other such equipment when others ask.
Short name set inArticle 135-3, paragraph (3)
transport pipe, etc.
「輸送管等」
In Articles 171-2 and 171-3, transport pipes and hoses.
Short name set inArticle 171-2, paragraph (1), item (iv)· applies only in this article and in Article 171-3