Search

Search provisions, jump to a law or an article

6 articles

Article 242Measures to Be Taken for Concrete Form Shoring

第二百四十二条(型枠支保工についての措置等)

As regards a concrete form shoring, the employer must comply with the following requirements:

事業者は、型枠支保工については、次に定めるところによらなければならない。

to take measures to prevent subsiding of the supports, such as the use of square timber, concrete placing, and use of posts;

敷角の使用、コンクリートの打設、くいの打込み等支柱の沈下を防止するための措置を講ずること。

to take measures to prevent sliding of the legs of the supports, such as fixing the leg parts and providing bridge batten of foot post;

支柱の脚部の固定、根がらみの取付け等支柱の脚部の滑動を防止するための措置を講ずること。

to use a butt joint or a bell-and-spigot joint for the joint of a support;

支柱の継手は、突合せ継手又は差込み継手とすること。

to fasten connecting and intersecting portions of steel materials with fittings such as bolts and clamps;

鋼材と鋼材との接続部及び交差部は、ボルト、クランプ等の金具を用いて緊結すること。

when concrete forms have curved surfaces, to take measures to prevent floating of the concrete form, such as use of stays;

型枠が曲面のものであるときは、控えの取付け等当該型枠の浮き上がりを防止するための措置を講ずること。

when H-steel or I-steel (hereinafter referred to as "H-steel, etc." in this item) is used as horizontal members such as sleepers and square timbers and there is a risk of deformation of the section of the H-steel, etc., due to the concentration of load on the point of connection between the H-steel, etc., and supports and jacks, etc., to attach reinforcing materials to the points of connection;

H型鋼又はI型鋼(以下この号において「H型鋼等」という。)を大引き、敷角等の水平材として用いる場合であつて、当該H型鋼等と支柱、ジャッキ等とが接続する箇所に集中荷重が作用することにより、当該H型鋼等の断面が変形するおそれがあるときは、当該接続する箇所に補強材を取り付けること。

for those using steel pipes (excluding adjustable tubular pole shores; hereinafter the same applies in this Article) as supports, the parts using the steel pipes is to conform to the requirements set forth in the following sub-items:

鋼管(パイプサポートを除く。以下この条において同じ。)を支柱として用いるものにあつては、当該鋼管の部分について次に定めるところによること。

to equip horizontal collar braces in two directions for each height of 2 m or less, and prevent displacement of the horizontal collar braces;

高さ二メートル以内ごとに水平つなぎを二方向に設け、かつ、水平つなぎの変位を防止すること。

when putting girders or sleepers on the top of the steel pipes, to fix an end plate of steel to the top and fasten to the girders or sleepers;

はり又は大引きを上端に載せるときは、当該上端に鋼製の端板を取り付け、これをはり又は大引きに固定すること。

for those using adjustable tubular pole shores as supports, the adjustable tubular pole shores are to conform to the requirements set forth in the following sub-items:

パイプサポートを支柱として用いるものにあつては、当該パイプサポートの部分について次に定めるところによること。

not to connect three or more adjustable tubular pole shores;

パイプサポートを三以上継いで用いないこと。

when connecting adjustable tubular pole shores, to connect them using four or more bolts or exclusively designed fittings;

パイプサポートを継いで用いるときは、四以上のボルト又は専用の金具を用いて継ぐこと。

when the height exceeds 3.5 m, to take measures set forth in (a) of the preceding item;

高さが三・五メートルを超えるときは、前号イに定める措置を講ずること。

for those using steel tubing frames as supports, parts using the steel tubing frames are to conform to the requirements of the following sub-items:

鋼管枠を支柱として用いるものにあつては、当該鋼管枠の部分について次に定めるところによること。

to equip cross bracings between the steel tubing frames;

鋼管枠と鋼管枠との間に交差筋かいを設けること。

to equip horizontal collar braces for each five frames or less in the direction of the side surface and the form surface of the concrete form shoring and in the direction of the cross bracings at the top layer and for each five layers or less, as well as prevent displacement of the horizontal collar braces;

最上層及び五層以内ごとの箇所において、型枠支保工の側面並びに枠面の方向及び交差筋かいの方向における五枠以内ごとの箇所に、水平つなぎを設け、かつ、水平つなぎの変位を防止すること。

to equip ledger forms in the direction of the cross bracings, at both ends of the concrete form shoring in the direction of the form surface and for each five frames or less at the top layer and for each five layers or less;

最上層及び五層以内ごとの箇所において、型枠支保工の枠面の方向における両端及び五枠以内ごとの箇所に、交差筋かいの方向に布枠を設けること。

to take the measures set forth in item (vi), (b);

第六号ロに定める措置を講ずること。

for those using built-up steel props as supports, the parts using the built-up steel props is to conform to the requirements set forth in the following sub-items:

組立て鋼柱を支柱として用いるものにあつては、当該組立て鋼柱の部分について次に定めるところによること。

to take the measures set forth in item (vi), (b);

第六号ロに定める措置を講ずること。

when the height exceeds 4 m, to equip horizontal collar braces in two directions for each height of 4 m or less, and prevent the displacement of the horizontal collar braces;

高さが四メートルを超えるときは、高さ四メートル以内ごとに水平つなぎを二方向に設け、かつ、水平つなぎの変位を防止すること。

for those using H-steel as supports, to take the measures set forth in item (vi), (b) for the parts using H-steel sections;

H型鋼を支柱として用いるものにあつては、当該H型鋼の部分について第六号ロに定める措置を講ずること。

for those using timber as supports, the parts using timber is to conform to the requirements set forth in the following sub-items:

木材を支柱として用いるものにあつては、当該木材の部分について次に定めるところによること。

to take the measures set forth in item (vi), (a);

第六号イに定める措置を講ずること。

when connecting two or more timbers, to connect them using two or more reinforcements;

木材を継いで用いるときは、二個以上の添え物を用いて継ぐこと。

when putting girders or sleepers on the top of the timber, to use reinforcements to fix the top to the girders or sleepers;

はり又は大引きを上端に載せるときは、添え物を用いて、当該上端をはり又は大引きに固定すること。

for those consisting of girders, they are to conform to the requirements set forth in the following sub-items:

はりで構成するものにあつては、次に定めるところによること。

to fix both ends of the girders to supporting members in order to prevent the girders from sliding and coming off;

はりの両端を支持物に固定することにより、はりの滑動及び脱落を防止すること。

to equip collar braces between the girders in order to prevent the girders from side buckling.

はりとはりとの間につなぎを設けることにより、はりの横倒れを防止すること。

Article 243Step-Like Concrete Form Shoring

第二百四十三条(段状の型わく支保工)

As regards concrete form shoring to be assembled in the shape of steps using planking, square timber, etc., the employer must comply with the requirements set forth in the following items, in addition to the requirements set forth in each item of the preceding Article:

事業者は、敷板、敷角等をはさんで段状に組み立てる型わく支保工については、前条各号に定めるところによるほか、次に定めるところによらなければならない。

not to use two or more layers of planking, square timbers, etc., excluding the case where it is unavoidable due to the configuration of the concrete form;

型わくの形状によりやむを得ない場合を除き、敷板、敷角等を二段以上はさまないこと。

when connecting planking, square timbers, etc., to tightly bind the planking, square timbers, etc.; and

敷板、敷角等を継いで用いるときは、当該敷板、敷角等を緊結すること。

to fix supports to the planking, square timbers, etc.

支柱は、敷板、敷角等に固定すること。

Article 244Concrete Placing Work

第二百四十四条(コンクリートの打設の作業)

When concrete placing work is carried out, the employer must comply with the following requirements:

事業者は、コンクリートの打設の作業を行なうときは、次に定めるところによらなければならない。

to inspect the concrete form shoring pertaining to the work before commencing the work for the day, and make repairs when having found an abnormality; and

その日の作業を開始する前に、当該作業に係る型わく支保工について点検し、異状を認めたときは、補修すること。

to have in place measures for suspending work when any abnormality is found on the concrete form shoring during work, in advance.

作業中に型わく支保工に異状が認められた際における作業中止のための措置をあらかじめ講じておくこと。

Article 245Work of Assembling Concrete Form Shoring

第二百四十五条(型わく支保工の組立て等の作業)

When carrying out the work of assembling or dismantling concrete form shoring, the employer must take the following measures:

事業者は、型わく支保工の組立て又は解体の作業を行うときは、次の措置を講じなければならない。

to prohibit persons other than persons engaged in work concerned from entering the area where the work is carried out, by indicating the prohibition in a conspicuous place or by other methods;

当該作業を行う区域に関係する作業従事者以外の者が立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止すること。

to not have the work carried out when dangers regarding the implementation of the work are expected due to bad weather conditions such as strong wind, heavy rain, and heavy snow; and

強風、大雨、大雪等の悪天候のため、作業の実施について危険が予想されるときは、当該作業を行わせないこと。

when raising or lowering the materials, instruments or tools, to have workers use a lifting rope, lifting bag, etc.

材料、器具又は工具を上げ、又はおろすときは、つり綱、つり袋等を労働者に使用させること。

Article 246Appointment of an Operations Supervisor of Assembling the Concrete Form Shoring

第二百四十六条(型枠支保工の組立て等作業主任者の選任)

As regards the work set forth in Article 6, item (xiv) of the Order, the employer must appoint an operations supervisor of assembling the concrete form shoring from the persons who have completed the skill training course for operations supervisor of assembling the concrete form shoring.

事業者は、令第六条第十四号の作業については、型枠支保工の組立て等作業主任者技能講習を修了した者のうちから、型枠支保工の組立て等作業主任者を選任しなければならない。

Article 247Duties of the Operations Supervisor of Assembling the Concrete Form Shoring

第二百四十七条(型枠支保工の組立て等作業主任者の職務)

The employer must have the operations supervisor of assembling the concrete form shoring carry out the following matters:

事業者は、型枠支保工の組立て等作業主任者に、次の事項を行わせなければならない。

to decide the work method and directly supervise the work;

作業の方法を決定し、作業を直接指揮すること。

To inspect defects in materials, instruments and tools, and remove those defective; and

材料の欠点の有無並びに器具及び工具を点検し、不良品を取り除くこと。

to monitor the use of fall arrest equipment with the required performance, etc., and safety helmet during work.

作業中、要求性能墜落制止用器具等及び保護帽の使用状況を監視すること。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy