When assembling or dismantling a transport pipe, etc., the employer must establish the method and procedures, etc., of the work, make them known to the workers, designate a person who supervises the work and have the workers carry out the work under the person's direct supervision.
At a road shoulder, an inclined place, etc. where there is a risk of endangering workers due to overturning or falling of a demolition machine whose total length of boom and arm is 12 m or more (hereinafter in this Article referred to as a "specified demolition machine"), the employer must not carry out work using a specified demolition machine; provided, however, that this does not apply when, at that place, measures to prevent that danger in accordance with the landform and the condition of the nature of the soil, etc. have been taken.
When there is a risk of endangering the operator due to objects that come flying, etc., the employer must not carry out work using a demolition machine without a driver's cabin; provided, however, that this does not apply when measures to prevent that danger in accordance with the circumstances of objects that come flying, etc. have been taken.
When carrying out work using a demolition machine, the employer must take the following measures (excluding the measure in item (ii) for the work set forth in Article 6, items (xv)-2, (xv)-3 and (xv)-5 of the Order):
to prohibit persons other than the operator from entering a place where there is a risk of danger due to objects that come flying, etc., by indicating the prohibition in a conspicuous place or by other methods;
to suspend the work when dangers involved in carrying out the work are expected due to bad weather conditions such as strong wind, heavy rain or heavy snow.
As regards bodies, accessory devices and fittings of a pile driver and a pile drawer driven by power (excluding those capable of self-propelling to unspecified places) and a boring machine, the employer must not use them unless they fall under the following requirements:
一
使用の目的に適応した必要な強度を有すること。
having necessary strength that conforms to the purpose of use; and
二
著しい損傷、摩耗、変形又は腐食のないものであること。
being free from marked damage, wear, deformation or corrosion.
As regards a pile driver driven by power (hereinafter referred to as "pile driver") or a pile drawer driven by power (hereinafter referred to as "pile drawer") or a boring machine, the employer must take the following measures for preventing its collapse:
一
軟弱な地盤に据え付けるときは、脚部又は架台の沈下を防止するため、敷板、敷角等を使用すること。
when installing the machine on soft ground, to use boards, blocks, etc., for preventing settling of legs or the cradle;
二
施設、仮設物等に据え付けるときは、その耐力を確認し、耐力が不足しているときは、これを補強すること。
when installing the machine in facilities or on a temporary construction, to confirm the durability, and when the durability is insufficient, to reinforce the durability;
三
脚部又は架台が滑動するおそれのあるときは、くい、くさび等を用いてこれを固定させること。
when there is a risk of the leg part or the cradle to slide, to secure the leg part or the cradle by using piles, wedges, etc.;
for a pile driver, a pile drawer or a boring machine designed to be moved on rollers or on rail tracks, to secure the machine with rail clamps, a stopper, etc., in order to prevent it from moving unexpectedly;
when the top part is to be stabilized only with stays (including bracing wires; hereinafter the same applies in this Section), to use three or more stays and secure each end of the stays to a sound tie bar, iron frame, etc.;
when the top part is to be stabilized only with bracing wires, to stabilize the top part in all directions by methods such as arranging the bracing wires at equal intervals and increasing the number of bracing wires; and
As regards a hoisting wire rope for a pile driver, a pile drawer or a boring machine, the employer must not use the ropes falling under any of the following items:
those in which 10% or more of the element wires (excluding filler wires; the same applies hereinafter in this item) have broken within one lay of the wire rope;
三
直径の減少が公称径の七パーセントをこえるもの
those with the reduction ratio of a diameter that exceeds 7% of the nominal diameter;
四
キンクしたもの
those with kinks; and
五
著しい形くずれ又は腐食があるもの
those with marked deformation or corrosion.
第百七十五条
(巻上げ用ワイヤロープの安全係数)Safety Coefficient of Hoisting Wire Ropes
The safety coefficient set forth in the preceding paragraph is to be the value obtained by dividing the breaking load of the wire rope by the maximum value of the load applied on to the wire rope.
hoisting wire ropes are to have a length sufficient to leave at least two windings on their drum of the hoisting equipment at the time when the dropping weight or hammer is placed at the lowest position, at the position for starting the drawing of a sheet pile or the suspension tool, including the rod, is at its lowest position;
二
巻上げ用ワイヤロープは、巻上げ装置の巻胴にクランプ、クリツプ等を用いて、確実に取り付けること。
hoisting wire ropes to be fixed securely to the drum of the hoisting device with clamps, clips, etc.; and
in connecting a dropping weight or a hammer to the hoisting wire rope of the pile driver or connecting the hoisting wire rope of the boring machine to a pulley block, a hoisting swivel, etc., clamps, clips, etc. are to be used to securely connect them.
As regards hoisting wire ropes, pulley blocks, etc., of a pile drawer or a boring machine, the employer must securely connect them with piles, sheet piles, rods, etc., by using such tools as shackles, checking fixtures, hoisting swivels, etc., that have sufficient strength.
As regards the winch used for a pile driver, a pile drawer or a boring machine, the employer must provide the machine with a ratchet or a brake equipped with a clamp; provided, however, that this does not apply to the winch used for a boring machine with a braking device such as a band brake.
As regards a winch of a pile driver, a pile drawer or a boring machine, the employer must install it in a manner that floating, shifting, sway, etc., may be prevented.
As regards the distance between the shaft of a drum barrel of a pile driver, pile drawer or boring machine and the shaft of the first sheave from the hoisting equipment, the employer must set the distance to a value equivalent to 15 times or more of the width of the drum of the hoisting equipment.
第二項
前項のみぞ車は、巻上げ装置の巻胴の中心を通り、かつ、軸に垂直な面上になければならない。
The sheave referred to in the preceding paragraph must go through the center of the drum of the hoisting equipment and be placed on a plane perpendicular to the shaft.
第三項
前二項の規定は、次の各号のいずれかに該当するときは、適用しない。
The provisions of the preceding two paragraphs do not apply to the cases falling under any of the following items:
一
くい打機、くい抜機又はボーリングマシンの構造上、巻上げ用ワイヤロープが乱巻となるおそれのないとき。
when there is no risk of irregular winding of the hoisting wire rope due to the structure of the pile driver, a pile drawer or a boring machine; or
when a boring machine is used for work in a very confined space such as a tunnel, etc., and the employer has prohibited a person engaged in work at the workshop from entering an area where there is a risk of danger due to the hoisting wire rope being cut, by indicating the prohibition in a conspicuous place or by other methods.
As regards sheaves or pulley blocks of a pile driver, a pile drawer or a boring machine, the employer must fasten the devices securely using fittings, shackles, wire ropes, etc., which do not have the risk of breaking by the load applied to the fixed part.
As regards sheaves of a pile driver, a pile drawer or a boring machine in which the winch is not integrated with the tower or the twin pillar, etc., the employer must place the sheaves so that the horizontal component of force acting on the hoisting wire rope does not affect the tower or the twin-pole; provided, however, when measures such as providing a prop to the leg of the tower or the twin pillar to support the leg by wire ropes are taken, sheaves may be fixed on the leg.
to firmly connect a steam hose or an air hose with a hammer at a place other than the joint parts of the hose and the hammer for preventing damages or disconnection of these joints parts due to the motion of the hammer.
二
蒸気又は空気をしや断するための装置をハンマーの運転者が容易に操作することができる位置に設けること。
to install a device for cutting off steam or air at a place where a hammer operator is able to easily handle the device.
第百八十四条
(乱巻時の措置)Measures to Be Taken When Irregular Winding Occurs
When a wire rope is wound irregularly on the drum of the hoisting equipment of a pile driver, a pile drawer or a boring machine, the employer must not have workers apply a load on the hoisting wire rope.
第百八十五条
(巻上げ装置停止時の措置)Measures to Be Taken When the Hoisting Device is Suspended
When leaving a hoisting device of a pile driver, a pile drawer or a boring machine suspended with the load applied to the hoisting equipment, the employer must securely suspend the machine by applying ratchets and using a brake with clamp.
第百八十六条
(運転位置からの離脱の禁止)Prohibition of Leaving the Operating Station
The employer must not allow the operator of a pile driver, a pile drawer or a boring machine to leave the operating station of the machine while loads are applied to the hoisting equipment.
第二項
前項の運転者は、巻上げ装置に荷重をかけたままで運転位置を離れてはならない。
The operator set forth in the preceding paragraph must not leave the operating station of a pile driver, a pile drawer or a boring machine while loads are applied to the hoisting equipment.