Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 April 2027, in 4 months

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter I Special Regulations Concerning Specified Principal Employers (Articles 643-12 to 655)

The law as Ministerial Order Partially Amending the Ordinance on Industrial Safety and Health (Ministry of Health, Labour and Welfare Order No. 112 of 2026) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Article 643-12第六百四十三条の十二

Measures to Be Taken by Work Site Managing Employers, etc.(作業場所管理事業者等の講ずべき措置)
Article 643-12, paragraph (1)

A work site managing employer, except in the case prescribed in Article 30-4 of the Act, when, at the one place it manages, persons engaged in work who are its workers (including, where there are persons engaged in work pertaining to that work site managing employer other than workers in addition to those persons engaged in work who are its workers, those persons) and persons engaged in work pertaining to other persons who conduct business at that one place perform operations that carry a risk of causing harm to persons engaged in work who work in the surrounding area or other operations, is to carry out liaison and coordination as needed between the work site managing employer and those persons who conduct business and between the persons who conduct business, in order to prevent industrial injuries arising from those operations being performed.

作業場所管理事業者は、法第三十条の四に規定する場合を除き、その管理する一の場所においてその労働者である作業従事者(当該労働者である作業従事者のほか、労働者以外の当該作業場所管理事業者に係る作業従事者がある場合には、当該者を含む。)及び当該一の場所において事業を行う他の事業を行う者に係る作業従事者が周囲で作業を行う作業従事者に危害を生ずるおそれのある作業その他の作業を行う場合には、当該作業が行われることによつて生ずる労働災害を防止するため、随時、作業場所管理事業者と当該事業を行う者との間及び事業を行う者相互間における連絡及び調整を行うものとする。

Article 643-12, paragraph (2)

A person who conducts business, where, at one place with no work site managing employer, its persons engaged in work and persons engaged in work pertaining to other persons who conduct business carried on at that one place perform the operations under the preceding paragraph (excluding the case where there are no workers among the persons engaged in work who perform operations at that one place), is to carry out mutual liaison and coordination as needed with those other persons who conduct business, in order to prevent industrial injuries arising from those operations being performed.

事業を行う者は、作業場所管理事業者がいない一の場所においてその作業従事者及び当該一の場所において行われる事業を行う他の事業を行う者に係る作業従事者が前項の作業を行う場合(当該一の場所において作業を行う作業従事者の中に労働者がいない場合を除く。)には、当該作業が行われることによつて生ずる労働災害を防止するため、随時、当該他の事業を行う者と相互に連絡及び調整を行うものとする。

Article 643-12, paragraph (3)

In the case under paragraph (1), persons who conduct business other than the work site managing employer are to take necessary measures in accordance with the measures taken by the work site managing employer.

第一項の場合において、作業場所管理事業者以外の事業を行う者は、作業場所管理事業者が行う措置に応じて、必要な措置を講ずるものとする。

Article 643-12, paragraph (4)

In the case under paragraph (1) or (2), persons engaged in work are to observe the necessary matters in accordance with the measures taken pursuant to the provisions of the preceding three paragraphs.

第一項又は第二項の場合において、作業従事者は、前三項の規定により講じられる措置に応じて、必要な事項を守るものとする。

Article 644第六百四十四条

Measures Concerning a Pile Driver and a Pile Drawer(くい打機及びくい抜機についての措置)
Article 644, paragraph (1)

The orderer set forth in Article 31, paragraph (1) of the Act (hereinafter referred to as the "orderer"), in the case set forth in the same paragraph, when having persons engaged in work pertaining to the contractor (meaning the contractor set forth in the same paragraph; hereinafter the same applies in this Chapter) use pile drivers or pile drawers, must conform the pile drivers or pile drawers to be used to the standards of pile drivers and pile drawers prescribed in Part II, Chapter II, Section 2 (limited to Article 172, Articles 174 through 176, Articles 178 through 181, and Article 183).

法第三十一条第一項の注文者(以下「注文者」という。)は、同項の場合において、請負人(同項の請負人をいう。以下この章において同じ。)に係る作業従事者にくい打機又はくい抜機を使用させるときは、当該くい打機又はくい抜機については、第二編第二章第二節(第百七十二条、第百七十四条から第百七十六条まで、第百七十八条から第百八十一条まで及び第百八十三条に限る。)に規定するくい打機又はくい抜機の基準に適合するものとしなければならない。

Article 645第六百四十五条

Measures Concerning Railway Equipment(軌道装置についての措置)
Article 645, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use railway equipment, the orderer must conform the railway equipment to be used to the standards of railway equipment prescribed in Part II, Chapter II, Section 3 (limited to Articles 196 through 204, Articles 207 through 209, Article 212, Article 213, and Articles 215 through 217).

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に軌道装置を使用させるときは、当該軌道装置については、第二編第二章第三節(第百九十六条から第二百四条まで、第二百七条から第二百九条まで、第二百十二条、第二百十三条及び第二百十五条から第二百十七条までに限る。)に規定する軌道装置の基準に適合するものとしなければならない。

Article 646第六百四十六条

Measures Concerning a Concrete Form Shoring(型わく支保工についての措置)
Article 646, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use concrete form shorings, the orderer must conform the concrete form shorings to the standards provided by the Minister of Health, Labour and Welfare pursuant to the provisions of Article 42, paragraph (1) of the Act and to the standards of concrete form shorings prescribed in Part II, Chapter III (limited to Articles 237 through 239, Article 242, and Article 243).

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に型わく支保工を使用させるときは、当該型わく支保工については、法第四十二条第一項の規定に基づき厚生労働大臣が定める規格及び第二編第三章(第二百三十七条から第二百三十九条まで、第二百四十二条及び第二百四十三条に限る。)に規定する型わく支保工の基準に適合するものとしなければならない。

Article 647第六百四十七条

Measures Concerning Acetylene Welding Equipment(アセチレン溶接装置についての措置)
Article 647, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use acetylene welding equipment, the orderer must take the following measures concerning the acetylene welding equipment:

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者にアセチレン溶接装置を使用させるときは、当該アセチレン溶接装置について、次の措置を講じなければならない。

Article 647, paragraph (1), item (i)

to install the acetylene welding equipment in an acetylene gas generator room which complies with the standards of the acetylene gas generator room prescribed in Article 302, paragraph (2) and (3) and Article 303;

第三百二条第二項及び第三項並びに第三百三条に規定する発生器室の基準に適合する発生器室内に設けること。

Article 647, paragraph (1), item (ii)

to ensure that the acetylene welding equipment which generates or uses the acetylene gas of a pressure of 7 kPa or more, complies with the standards prescribed in Article 305, paragraph (1);

ゲージ圧力七キロパスカル以上のアセチレンを発生し、又は使用するアセチレン溶接装置にあつては、第三百五条第一項に規定する基準に適合するものとすること。

Article 647, paragraph (1), item (iii)

to not use copper as regards the purifier and conduits of the acetylene welding equipment other than that set forth in the preceding item, for the part which has a risk of coming into contact with acetylene gas;

前号のアセチレン溶接装置以外のアセチレン溶接装置の清浄器、導管等でアセチレンが接触するおそれのある部分には、銅を使用しないこと。

Article 647, paragraph (1), item (iv)

to conform the acetylene gas generator and safety equipment to the standards provided by the Minister of Health, Labour and Welfare pursuant to the provisions of Article 42, paragraph (1) of the Act; and

発生器及び安全器は、法第四十二条第一項の規定に基づき厚生労働大臣が定める規格に適合するものとすること。

Article 647, paragraph (1), item (v)

to conform the safety equipment to the standards prescribed in Article 306.

安全器の設置については、第三百六条に規定する基準に適合するものとすること。

Article 648第六百四十八条

Measures Concerning Alternating-Current Arc Welding Equipment(交流アーク溶接機についての措置)
Article 648, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use alternating current arc welding equipment (excluding automatic welding equipment), the orderer must provide the alternating current arc welding equipment with an automatic voltage reducing device which complies with the standards provided by the Minister of Health, Labour and Welfare pursuant to the provisions of Article 42, paragraph (1) of the Act; provided, however, that this does not apply when the equipment is used at places other than the following places:

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に交流アーク溶接機(自動溶接機を除く。)を使用させるときは、当該交流アーク溶接機に、法第四十二条第一項の規定に基づき厚生労働大臣が定める規格に適合する交流アーク溶接機用自動電撃防止装置を備えなければならない。ただし、次の場所以外の場所において使用させるときは、この限りでない。

Article 648, paragraph (1), item (i)

the inside of a double-bottomed vessel or peak tank and other very confined places surrounded by electric conductors; and

船舶の二重底又はピークタンクの内部その他導電体に囲まれた著しく狭あいな場所

Article 648, paragraph (1), item (ii)

places at a height of 2 m or more where there is a risk of endangering persons engaged in work due to falling, and where there is a risk of persons engaged in work coming into contact with highly conductive grounded objects such as steel frames.

墜落により作業従事者に危険を及ぼすおそれのある高さが二メートル以上の場所で、鉄骨等導電性の高い接地物に作業従事者が接触するおそれのあるところ

Article 649第六百四十九条

Measures Concerning Motor-Driven Appliances(電動機械器具についての措置)
Article 649, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use machines or equipment driven by motor (hereinafter referred to as "motor-driven appliance" in this Article) that are movable or portable with a voltage to ground exceeding 150 V, or that are movable or portable and used at places moistened with water or other liquids of high electric conduction or at places of high electric conduction such as on iron plates, steel frames and surface plates, the orderer must connect to the electrical circuit to which the motor-driven appliance is connected an earth-leakage circuit breaker for preventing electric shocks that complies with the rating of the electrical circuit, has good sensitivity and works reliably.

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に電動機を有する機械又は器具(以下この条において「電動機械器具」という。)で、対地電圧が百五十ボルトを超える移動式若しくは可搬式のもの又は水等導電性の高い液体によつて湿潤している場所その他鉄板上、鉄骨上、定盤上等導電性の高い場所において使用する移動式若しくは可搬式のものを使用させるときは、当該電動機械器具が接続される電路に、当該電路の定格に適合し、感度が良好であり、かつ、確実に作動する感電防止用漏電しや断装置を接続しなければならない。

Article 649, paragraph (2)

The orderer set forth in the preceding paragraph, when it is difficult to take the measures prescribed in the same paragraph, must ensure that the metallic portion of the outer frame of the motor-driven appliance or the cover of the motor is grounded pursuant to the provisions of each item of Article 333, paragraph (2).

前項の注文者は、同項に規定する措置を講ずることが困難なときは、電動機械器具の金属性外わく、電動機の金属製外被等の金属部分を、第三百三十三条第二項各号に定めるところにより接地できるものとしなければならない。

Article 650第六百五十条

Measures Concerning a Caisson(潜函等についての措置)
Article 650, paragraph (1)

The orderer, in the case set forth in Article 31, paragraph (1) of the Act, when having persons engaged in work pertaining to the contractor use caissons, etc., and when those persons engaged in work carry out open-cut excavating work inside the caissons, etc., must take the following measures concerning the caissons, etc.:

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に潜函等を使用させる場合で、当該作業従事者が当該潜函等の内部で明り掘削の作業を行うときは、当該潜函等について、次の措置を講じなければならない。

Article 650, paragraph (1), item (i)

to install an air supply equipment when the depth of excavating exceeds 20 m; and

掘下げの深さが二十メートルをこえるときは、送気のための設備を設けること。

Article 650, paragraph (1), item (ii)

beyond what is set forth in the preceding item, to ensure that the caisson complies with the standards of caisson, etc., prescribed in Part II, Chapter VI, Section 1, Subsection 3 (limited to Article 376, item (ii), and Article 377, paragraph (1), items (ii) and (iii)).

前号に定めるもののほか、第二編第六章第一節第三款(第三百七十六条第二号並びに第三百七十七条第一項第二号及び第三号に限る。)に規定する潜函等の基準に適合するものとすること。

Article 651第六百五十一条

Measures Concerning Tunnels(ずい道等についての措置)
Article 651, paragraph (1)

The orderer, in the case set forth in Article 31, paragraph (1) of the Act, when having persons engaged in work pertaining to the contractor use tunnels, etc., and when those persons engaged in work carry out the construction work of tunnels, etc. (limited to cases where there is a risk of endangering persons engaged in work due to cave-ins or falling of rocks), must take measures to prevent cave-ins or falling of rocks, such as providing tunnel shoring and installing rock bolts in the tunnels, etc.

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者にずい道等を使用させる場合で、当該作業従事者がずい道等の建設の作業を行うとき(落盤又は肌落ちにより作業従事者に危険を及ぼすおそれのあるときに限る。)は、当該ずい道等についてずい道支保工を設け、ロツクボルトを施す等落盤又は肌落ちを防止するための措置を講じなければならない。

Article 651, paragraph (2)

As regards the tunnel shoring set forth in the preceding paragraph, the orderer must ensure that the shoring complies with the standards of the tunnel shoring prescribed in Part II, Chapter VI, Section 2, Subsection 2 (limited to Article 390, Article 391, and Article 394).

注文者は、前項のずい道支保工については、第二編第六章第二節第二款(第三百九十条、第三百九十一条及び第三百九十四条に限る。)に規定するずい道支保工の基準に適合するものとしなければならない。

Article 652第六百五十二条

Measures Concerning Tunnel Concrete Form Shorings(ずい道型わく支保工についての措置)
Article 652, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use tunnel concrete form shorings, the orderer must ensure that the tunnel concrete form shorings comply with the standards of tunnel concrete form shorings prescribed in Part II, Chapter VI, Section 2, Subsection 3.

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者にずい道型わく支保工を使用させるときは、当該ずい道型わく支保工を、第二編第六章第二節第三款に規定するずい道型わく支保工の基準に適合するものとしなければならない。

Article 653第六百五十三条

Measures Concerning a Hoistway(物品揚卸口等についての措置)
Article 653, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use work floors, hoistways, pits, shafts or hatches of vessels, the orderer must install enclosures, handrails, covers, etc., at places where the height of these construction, equipment, or raw material is 2 m or more and there is a risk of endangering persons engaged in work due to falling; provided, however, that this does not apply when it is difficult to install enclosures, handrails, covers, etc., due to the nature of the work.

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に、作業床、物品揚卸口、ピツト、坑又は船舶のハツチを使用させるときは、これらの建設物等の高さが二メートル以上の箇所で墜落により作業従事者に危険を及ぼすおそれのあるところに囲い、手すり、覆い等を設けなければならない。ただし、囲い、手すり、覆い等を設けることが作業の性質上困難なときは、この限りでない。

Article 653, paragraph (2)

In the case referred to in the preceding paragraph, for a work floor located at a place exceeding 1.5 m in height or in depth, the orderer must install facilities, etc., for persons engaged in work to ascend and descend safely.

注文者は、前項の場合において、作業床で高さ又は深さが一・五メートルを超える箇所にあるものについては、作業従事者が安全に昇降するための設備等を設けなければならない。

Article 654第六百五十四条

Measures Concerning a Temporary Passage(架設通路についての措置)
Article 654, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use a temporary passage, the orderer must ensure that the temporary passage complies with the standards of temporary passages prescribed in Article 552.

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に架設通路を使用させるときは、当該架設通路を、第五百五十二条に規定する架設通路の基準に適合するものとしなければならない。

Article 655第六百五十五条

Measures Concerning Scaffoldings(足場についての措置)
Article 655, paragraph (1)

In the case set forth in Article 31, paragraph (1) of the Act, when the orderer has persons engaged in work pertaining to the contractor use scaffoldings, the orderer must take the following measures concerning the scaffoldings:

注文者は、法第三十一条第一項の場合において、請負人に係る作業従事者に、足場を使用させるときは、当該足場について、次の措置を講じなければならない。

Article 655, paragraph (1), item (i)

to set the maximum loading capacity of the work floor in accordance with the structure and material used, and to display the capacity at a readily visible place of the scaffolding;

構造及び材料に応じて、作業床の最大積載荷重を定め、かつ、これを足場の見やすい場所に表示すること。

Article 655, paragraph (1), item (ii)

after bad weather such as strong wind, heavy rain or heavy snow, a moderate or greater earthquake, or the assembly, partial dismantling or alteration of a scaffolding, to designate an inspector and have that person inspect the following matters before commencing work on the scaffolding, and to promptly make repairs when there is a risk of danger:

強風、大雨、大雪等の悪天候若しくは中震以上の地震又は足場の組立て、一部解体若しくは変更の後においては、点検者を指名して、足場における作業を開始する前に、次の事項について点検させ、危険のおそれがあるときは、速やかに修理すること。

Article 655, paragraph (1), item (ii), (a)

condition of damage, mounting and placing of floor materials;

床材の損傷、取付け及び掛渡しの状態

Article 655, paragraph (1), item (ii), (b)

condition of loosening of the fastening, connecting and mounting parts of standards, ledgers, brackets, etc.;

建地、布、腕木等の緊結部、接続部及び取付部の緩みの状態

Article 655, paragraph (1), item (ii), (c)

condition of damage and corrosion of clamping materials and clamps;

緊結材及び緊結金具の損傷及び腐食の状態

Article 655, paragraph (1), item (ii), (d)

whether the scaffold fall prevention equipment has been removed or has come off;

足場用墜落防止設備の取り外し及び脱落の有無

Article 655, paragraph (1), item (ii), (e)

condition of mounting of toe boards, etc., and whether they have been removed;

幅木等の取付状態及び取り外しの有無

Article 655, paragraph (1), item (ii), (f)

condition of settling and sliding of leg parts;

脚部の沈下及び滑動の状態

Article 655, paragraph (1), item (ii), (g)

condition of mounting of bracings, stays, ties to the wall and other reinforcement materials;

筋かい、控え、壁つなぎ等の補強材の取付けの状態

Article 655, paragraph (1), item (ii), (h)

damage of standards, ledgers and brackets; and

建地、布及び腕木の損傷の有無

Article 655, paragraph (1), item (ii), (i)

condition of the mounting part of projected girders and lifting cables, and the function of the stoppers of lifting devices;

突りようとつり索との取付部の状態及びつり装置の歯止めの機能

Article 655, paragraph (1), item (iii)

beyond what is set forth in the preceding two items, to ensure that the scaffoldings comply with the standards specified by the Minister of Health, Labour and Welfare pursuant to the provisions of Article 42, paragraph (1) of the Act and the standards of scaffoldings prescribed in Part II, Chapter X, Section 2 (limited to Articles 559 through 561, Article 562, paragraph (2), Article 563, Articles 569 through 572, and Article 574).

前二号に定めるもののほか、法第四十二条第一項の規定に基づき厚生労働大臣が定める規格及び第二編第十章第二節(第五百五十九条から第五百六十一条まで、第五百六十二条第二項、第五百六十三条、第五百六十九条から第五百七十二条まで及び第五百七十四条に限る。)に規定する足場の基準に適合するものとすること。

Article 655, paragraph (2)

When the orderer has conducted the inspection under item (ii) of the preceding paragraph, the orderer must record the following matters and retain them until the work in which operations using the scaffoldings are carried out is completed:

注文者は、前項第二号の点検を行つたときは、次の事項を記録し、足場を使用する作業を行う仕事が終了するまでの間、これを保存しなければならない。

Article 655, paragraph (2), item (i)

the results of that inspection and the name of the inspector;

当該点検の結果及び点検者の氏名

Article 655, paragraph (2), item (ii)

in the case where measures such as repairs have been taken based on the results referred to in the preceding item, the content of those measures.

前号の結果に基づいて修理等の措置を講じた場合にあつては、当該措置の内容

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy