Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 January 2027, in 43 days

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter I Prevention of Dangers Due to Machines (Articles 133 to 141)

The law as Ministerial Order Partially Amending the Ordinance on Industrial Safety and Health and the Ordinance for Enforcement of the Act on Ensuring the Proper Operation of Worker Dispatching Services and Protecting Dispatched Workers (Ministry of Health, Labour and Welfare Order No. 120 of 2025) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Article 133第百三十三条

Appointment of an Operations Supervisor of Press Machines(プレス機械作業主任者の選任)
Article 133, paragraph (1)

As regards the work set forth in Article 6, item (vii) of the Order, the employer must appoint an operations supervisor of press machines from the persons who have completed the skill training course for operations supervisor of press machines.

事業者は、令第六条第七号の作業については、プレス機械作業主任者技能講習を修了した者のうちから、プレス機械作業主任者を選任しなければならない。

Article 134第百三十四条

Duties of the Operations Supervisor of Press Machines(プレス機械作業主任者の職務)
Article 134, paragraph (1)

The employer must have the operations supervisor of press machines carry out the following matters:

事業者は、プレス機械作業主任者に、次の事項を行なわせなければならない。

Article 134, paragraph (1), item (i)

to inspect the press machine and its safety device;

プレス機械及びその安全装置を点検すること。

Article 134, paragraph (1), item (ii)

to immediately take necessary measures when having found any abnormality in the press machine and its safety device;

プレス機械及びその安全装置に異常を認めたときは、直ちに必要な措置をとること。

Article 134, paragraph (1), item (iii)

To store the key when having equipped a press machine or its safety device with a changeover key switch; and

プレス機械及びその安全装置に切替えキースイツチを設けたときは、当該キーを保管すること。

Article 134, paragraph (1), item (iv)

to directly supervise the work of fitting, removing and adjusting a die.

金型の取付け、取りはずし及び調整の作業を直接指揮すること。

Article 134-2第百三十四条の二

Storing the Key of a Changeover Key Switch(切替えキースイツチのキーの保管等)
Article 134-2, paragraph (1)

When work other than those set forth in Article 6, item (vii) of the Order among work using a power press are carried out, and a changeover key switch for the power press and its safety device have been provided, the employer must designate a person who stores the key switch, and have the person store the key.

事業者は、動力プレスによる作業のうち令第六条第七号の作業以外の作業を行う場合において、動力プレス及びその安全装置に切替えキースイツチを設けたときは、当該キーを保管する者を定め、その者に当該キーを保管させなければならない。

Article 134-3第百三十四条の三

Periodical Self-inspections(定期自主検査)
Article 134-3, paragraph (1)

As regards a power press, the employer must carry out self-inspections for the following matters periodically once every period not exceeding a year; provided, however, that this does not apply to the non-use period of a power press which is not used for a period exceeding one year:

事業者は、動力プレスについては、一年以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一年を超える期間使用しない動力プレスの当該使用しない期間においては、この限りでない。

Article 134-3, paragraph (1), item (i)

abnormalities in crankshafts, flywheels and other power transmission devices;

クランクシヤフト、フライホイールその他動力伝達装置の異常の有無

Article 134-3, paragraph (1), item (ii)

abnormalities in a clutch, a brake and other controlling systems;

クラツチ、ブレーキその他制御系統の異常の有無

Article 134-3, paragraph (1), item (iii)

abnormalities in an anti-repeat device, a quick-stop device or an emergency stop device;

一行程一停止機構、急停止機構及び非常停止装置の異常の有無

Article 134-3, paragraph (1), item (iv)

abnormalities in a slide, a connecting rod or other slide-related parts;

スライド、コネクチングロツドその他スライド関係の異常の有無

Article 134-3, paragraph (1), item (v)

abnormalities in a magnet valve, a pressure control valve or other air pressure systems;

電磁弁、圧力調整弁その他空圧系統の異常の有無

Article 134-3, paragraph (1), item (vi)

abnormalities in a magnet valve, a hydraulic pump or other hydraulic systems;

電磁弁、油圧ポンプその他油圧系統の異常の有無

Article 134-3, paragraph (1), item (vii)

abnormalities in a limit switch, a relay or other electrical systems;

リミツトスイツチ、リレーその他電気系統の異常の有無

Article 134-3, paragraph (1), item (viii)

abnormalities in a die cushion and its accessories; and

ダイクツシヨン及びその附属機器の異常の有無

Article 134-3, paragraph (1), item (ix)

abnormalities in the mechanism for preventing dangers due to a slide.

スライドによる危険を防止するための機構の異常の有無

Article 134-3, paragraph (2)

As regards the power press set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.

事業者は、前項ただし書の動力プレスについては、その使用を再び開始する際に、同項各号に掲げる事項について自主検査を行わなければならない。

Article 135第百三十五条

Article 135, paragraph (1)

As regards a power-driven shearing machine, the employer must carry out self-inspections for the following matters periodically once every period not exceeding a year; provided, however, that this does not apply to the non-use period of a power-driven shearing machine which is not used for a period exceeding one year:

事業者は、動力により駆動されるシヤーについては、一年以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一年を超える期間使用しないシヤーの当該使用しない期間においては、この限りでない。

Article 135, paragraph (1), item (i)

abnormalities in a clutch and a brake;

クラツチ及びブレーキの異常の有無

Article 135, paragraph (1), item (ii)

abnormalities in a sliding mechanism;

スライド機構の異常の有無

Article 135, paragraph (1), item (iii)

abnormalities in an anti-repeat device, a quick-stop device, and an emergency stop device;

一行程一停止機構、急停止機構及び非常停止装置の異常の有無

Article 135, paragraph (1), item (iv)

abnormalities in a magnet valve, a pressure-reducing valve and a pressure gauge; and

電磁弁、減圧弁及び圧力計の異常の有無

Article 135, paragraph (1), item (v)

abnormalities in wiring and switches.

配線及び開閉器の異常の有無

Article 135, paragraph (2)

As regards the shearing machine set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.

事業者は、前項ただし書のシヤーについては、その使用を再び開始する際に、同項各号に掲げる事項について自主検査を行わなければならない。

Article 135-2第百三十五条の二

Record of Periodical Self-inspections(定期自主検査の記録)
Article 135-2, paragraph (1)

When having carried out the self-inspections set forth in the preceding two Articles, the employer must record the following matters and preserve the records for three years:

事業者は、前二条の自主検査を行つたときは、次の事項を記録し、これを三年間保存しなければならない。

Article 135-2, paragraph (1), item (i)

the date of the inspection;

検査年月日

Article 135-2, paragraph (1), item (ii)

the method of the inspection;

検査方法

Article 135-2, paragraph (1), item (iii)

the parts of a machine inspected;

検査箇所

Article 135-2, paragraph (1), item (iv)

the results of the inspection;

検査の結果

Article 135-2, paragraph (1), item (v)

the name of the person who has carried out the inspection; and

検査を実施した者の氏名

Article 135-2, paragraph (1), item (vi)

when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.

検査の結果に基づいて補修等の措置を講じたときは、その内容

Article 135-3第百三十五条の三

Specified Self-inspections(特定自主検査)
Article 135-3, paragraph (1)

The self-inspection prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to a power press (hereinafter referred to as the "specified inspection") is to be the self-inspection prescribed in Article 134-3.

動力プレスに係る法第四十五条第二項の厚生労働省令で定める自主検査(以下「特定自主検査」という。)は、第百三十四条の三に規定する自主検査とする。

Article 135-3, paragraph (2)

A person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to a power press is to be a person who falls under any of the following items:

動力プレスに係る法第四十五条第二項の厚生労働省令で定める資格を有するものは、次の各号のいずれかに該当する者とする。

Article 135-3, paragraph (2), item (i)

a person who falls under any of the following sub-items and has completed the training course specified by the Minister of Health, Labour and Welfare:

次のいずれかに該当する者で、厚生労働大臣が定める研修を修了したもの

Article 135-3, paragraph (2), item (i), (a)

a person who has majored in and graduated from an engineering course of a university or a technical college under the School Education Act (including a person who has been conferred a bachelor's degree by the National Institution for Academic Degrees and Quality Enhancement of Higher Education (limited to one who majored in such a course), a person found to have equivalent or greater scholastic ability, and a person who majored in such a course and completed the first-stage course of a professional university; the same applies in Article 151-24, paragraph (2), item (i), (a)), and has experience of having been engaged in the work of inspection or maintenance of a power press for two years or longer, or design or manufacture of a power press for five years or longer;

学校教育法による大学又は高等専門学校において工学に関する学科を専攻して卒業した者(大学改革支援・学位授与機構により学士の学位を授与された者(当該学科を専攻した者に限る。)若しくはこれと同等以上の学力を有すると認められる者又は当該学科を専攻して専門職大学前期課程を修了した者を含む。第百五十一条の二十四第二項第一号イにおいて同じ。)で、動力プレスの点検若しくは整備の業務に二年以上従事し、又は動力プレスの設計若しくは工作の業務に五年以上従事した経験を有するもの

Article 135-3, paragraph (2), item (i), (b)

a person who has majored in and graduated from an engineering course of a senior high school or a secondary education school under the School Education Act and has experience of having been engaged in the work of inspection or maintenance of a power press for four years or longer, or design or manufacture of a power press for seven years or longer;

学校教育法による高等学校又は中等教育学校において工学に関する学科を専攻して卒業した者で、動力プレスの点検若しくは整備の業務に四年以上従事し、又は動力プレスの設計若しくは工作の業務に七年以上従事した経験を有するもの

Article 135-3, paragraph (2), item (i), (c)

a person who has experience of having been engaged in the work of inspection or maintenance of a power press for seven years or longer, or design or manufacture of a power press for 10 years or longer; or

動力プレスの点検若しくは整備の業務に七年以上従事し、又は動力プレスの設計若しくは工作の業務に十年以上従事した経験を有する者

Article 135-3, paragraph (2), item (i), (d)

a person who has completed the skill training course for operations supervisor of press machine listed in the Appended Table 18, item (2) of the Act and who has experience of having been engaged in the work using a power press for 10 years or longer; or

法別表第十八第二号に掲げるプレス機械作業主任者技能講習を修了した者で、動力プレスによる作業に十年以上従事した経験を有するもの

Article 135-3, paragraph (2), item (ii)

other persons specified by the Minister of Health, Labour and Welfare.

その他厚生労働大臣が定める者

Article 135-3, paragraph (3)

As regards the application of the provisions of the preceding Article when having a registered inspection agency set forth in Article 45, paragraph (2) of the Act (hereinafter referred to as the "registered inspection agency") conduct the specified inspection pertaining to a power press, the term "the name of the person who has carried out the inspection" in item (v) of the same Article is deemed to be replaced with "the name of the registered inspection agency."

動力プレスに係る特定自主検査を法第四十五条第二項の検査業者(以下「検査業者」という。)に実施させた場合における前条の規定の適用については、同条第五号中「検査を実施した者の氏名」とあるのは、「検査業者の名称」とする。

Article 135-3, paragraph (4)

When having carried out the specified inspection pertaining to a power press, the employer must affix an inspection sticker stating the month and year when the specified inspection was carried out at a readily visible part of the power press.

事業者は、動力プレスに係る特定自主検査を行つたときは、当該動力プレスの見やすい箇所に、特定自主検査を行つた年月を明らかにすることができる検査標章をはり付けなければならない。

Article 136第百三十六条

Inspection before Commencing the Work(作業開始前の点検)
Article 136, paragraph (1)

When carrying out the work using press, etc., the employer must inspect the following matters before commencing the work for the day:

事業者は、プレス等を用いて作業を行うときには、その日の作業を開始する前に、次の事項について点検を行わなければならない。

Article 136, paragraph (1), item (i)

the function of a clutch and a brake;

クラツチ及びブレーキの機能

Article 136, paragraph (1), item (ii)

the slackness of a bolt of a crankshaft, a flywheel, a slide, a connecting rod and a connecting screw;

クランクシヤフト、フライホイール、スライド、コネクチングロツド及びコネクチングスクリユーのボルトのゆるみの有無

Article 136, paragraph (1), item (iii)

the function of an anti-repeat device, quick-stop device and an emergency stop device;

一行程一停止機構、急停止機構及び非常停止装置の機能

Article 136, paragraph (1), item (iv)

the function of mechanism for preventing dangers due to a slide or a blade;

スライド又は刃物による危険を防止するための機構の機能

Article 136, paragraph (1), item (v)

the conditions of a die and a bolster for a press machine; and

プレス機械にあつては、金型及びボルスターの状態

Article 136, paragraph (1), item (vi)

the conditions of a blade and a table for a shearing machine.

シヤーにあつては、刃物及びテーブルの状態

Article 137第百三十七条

Repair of Press Machines(プレス等の補修)
Article 137, paragraph (1)

When having found any abnormality in carrying out the self-inspection set forth in Article 134-3 or Article 135, or the inspection set forth in the preceding Article, the employer must make repairs or take other necessary measures.

事業者は、第百三十四条の三若しくは第百三十五条の自主検査又は前条の点検を行つた場合において、異常を認めたときは、補修その他の必要な措置を講じなければならない。

Section 5 Centrifugal Machine第五節 遠心機械

Article 138第百三十八条

Fitting of a Lid(ふたの取付け)
Article 138, paragraph (1)

The employer must provide a lid on a centrifugal machine.

事業者は、遠心機械には、ふたを設けなければならない。

Article 139第百三十九条

Suspension of Operation in Taking Out the Contents(内容物を取り出す場合の運転停止)
Article 139, paragraph (1)

When taking out the contents of a centrifugal machine (excluding the centrifugal machine constructed so that the content is automatically taken out), the employer must suspend the operation of the centrifugal machine.

事業者は、遠心機械(内容物の取出しが自動的に行なわれる構造のものを除く。)から内容物を取り出すときは、当該機械の運転を停止しなければならない。

Article 140第百四十条

Prohibition of Use at Speeds Exceeding Maximum Allowable Rotation(最高使用回転数をこえる使用の禁止)
Article 140, paragraph (1)

As regards a centrifugal machine, the employer must not use the centrifugal machine at a speed exceeding its maximum allowable rotating speed.

事業者は、遠心機械については、その最高使用回転数をこえて使用してはならない。

Article 141第百四十一条

Periodical Self-inspections(定期自主検査)
Article 141, paragraph (1)

As regards a power-driven centrifugal machine, the employer must carry out self-inspections for the following matters periodically once every period not exceeding a year; provided, however, that this does not apply to the non-use period of a centrifugal machine which is not used for a period exceeding one year:

事業者は、動力により駆動される遠心機械については、一年以内ごとに一回、定期に、次の事項について自主検査を行なわなければならない。ただし、一年をこえる期間使用しない遠心機械の当該使用しない期間においては、この限りでない。

Article 141, paragraph (1), item (i)

abnormalities in rotor;

回転体の異常の有無

Article 141, paragraph (1), item (ii)

abnormalities in bearing parts of the main shafts;

主軸の軸受部の異常の有無

Article 141, paragraph (1), item (iii)

abnormalities in brake;

ブレーキの異常の有無

Article 141, paragraph (1), item (iv)

abnormalities in the outer frame; and

外わくの異常の有無

Article 141, paragraph (1), item (v)

the slackness of a bolt used in the parts listed in each preceding item.

前各号に掲げる部分のボルトのゆるみの有無

Article 141, paragraph (2)

As regards the centrifugal machine set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the use.

事業者は、前項ただし書の遠心機械については、その使用を再び開始する際に、同項各号に掲げる事項について自主検査を行なわなければならない。

Article 141, paragraph (3)

When having carried out the self-inspections set forth in the preceding two paragraphs, the employer must record the following matters and preserve the record for three years:

事業者は、前二項の自主検査を行つたときは、次の事項を記録し、これを三年間保存しなければならない。

Article 141, paragraph (3), item (i)

the date of the inspection;

検査年月日

Article 141, paragraph (3), item (ii)

the method of the inspection;

検査方法

Article 141, paragraph (3), item (iii)

the parts inspected;

検査箇所

Article 141, paragraph (3), item (iv)

the results of the inspection;

検査の結果

Article 141, paragraph (3), item (v)

the name of the person who has carried out the inspection; and

検査を実施した者の氏名

Article 141, paragraph (3), item (vi)

when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.

検査の結果に基づいて補修等の措置を講じたときは、その内容

Article 141, paragraph (4)

When having found any abnormality in carrying out the self-inspection set forth in paragraph (1) or paragraph (2), the employer must make repairs or take other necessary measures.

事業者は、第一項又は第二項の自主検査を行なつた場合において、異常を認めたときは、補修その他の必要な措置を講じなければならない。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy