事業者は、発生器室については、次に定めるところによらなければならない。
As regards a generator room, the employer must conform to the requirements set forth in the following items:
条文、法令、用語を検索します
この条文はまだされていません2027年4月1日から施行予定(4か月後)
いまの条文を読む →第四章 爆発、火災等の防止(第三百三条から第三百十三条まで)
労働安全衛生規則の一部を改正する省令(令和七年厚生労働省令第十二号)による改正後の条文です。変わる言葉に印をつけています。
本則は章ごとのページで読みます。長い章は、さらに条のまとまりごとに分けています。本則の全条文と、この改正が変える附則・別表を示します。この改正が触れていない附則や別表は、いま施行されている条文のページでご覧ください。
事業者は、発生器室については、次に定めるところによらなければならない。
As regards a generator room, the employer must conform to the requirements set forth in the following items:
壁は、不燃性のものとし、次の構造又はこれと同等以上の強度を有する構造のものとすること。
to be constructed with an incombustible wall, and to have the following structure or a structure with the strength equivalent to or stronger than those listed in the following sub-items:
厚さ四センチメートル以上の鉄筋コンクリートとすること。
to be made of ferroconcrete with the thickness of 4 cm or more; and
鉄骨若しくは木骨に厚さ三センチメートル以上のメタルラス張モルタル塗りをし、又は鉄骨に厚さ一・五ミリメートル以上の鉄板張りをしたものとすること。
to be made of steel or lumber on which metal lath is lined and mortar is painted 3 cm or more in thickness, or of steel on which an iron plate with thickness of 1.5 mm or more are lined;
屋根及び天井には、薄鉄板又は軽い不燃性の材料を使用すること。
to use thin iron plate or lightweight incombustible materials for the roof and ceiling;
床面積の十六分の一以上の断面積をもつ排気筒を屋上に突出させ、かつ、その開口部は窓、出入口その他の孔口から一・五メートル以上離すこと。
to project an exhaust pipe having a cross-section area of one-sixteenth of the floor area or more from the roof, and place the opening of the pipe at a distance of 1.5 m or more from a window, an entrance and other openings;
出入口の戸は、厚さ一・五ミリメートル以上の鉄板を使用し、又は不燃性の材料を用いてこれと同等以上の強度を有する構造とすること。
to use an iron plate with the thickness of 1.5 mm or more, or with a structure having the same strength as the iron plate or stronger using incombustible materials for the door of an entrance;
壁と発生器との間隔は、発生器の調整又はカーバイド送給等の作業を妨げない距離とすること。
to keep the space between a wall and a generator that does not hinder the work of adjusting the generator, or the work of feeding of carbide, etc.
事業者は、移動式のアセチレン溶接装置については、第三百二条第一項の規定にかかわらず、これを使用しないときは、専用の格納室に収容しなければならない。ただし、気鐘を分離し、発生器を洗浄した後保管するときは、この限りでない。
As regards movable acetylene welding equipment, notwithstanding the provisions of Article 302, paragraph (1), the employer must store the equipment in a dedicated storeroom when it is not used; provided, however, that this does not apply when storing the equipment after its gas bell is removed and the generator is washed.
事業者は、前項の格納室については、木骨鉄板張、木骨スレート張等耐火性の構造としなければならない。
As regards the storeroom referred to in the preceding paragraph, the employer must construct it by using fire-proof materials such as iron plate-lined lumber and slate-lined lumber.
事業者は、ゲージ圧力(以下この条において「圧力」という。)七キロパスカル以上のアセチレンを発生し、又は使用するアセチレン溶接装置(発生器及び安全器を除く。)については、次に定めるところに適合するものとしなければならない。
As regards acetylene welding equipment (excluding generators and safety equipment) that generate or use acetylene of a gauge pressure (hereinafter referred to as "pressure" in this Article) of 7 kPa or more, the employer must conform to the requirements set forth in the following items:
ガスだめは、次に定めるところによるものであること。
the gas holder conforms to the following requirements:
主要部分は、次の表の上欄に掲げる内径に応じ、それぞれ同表の下欄に掲げる厚さ以上の鋼板又は鋼管で造られていること。
| 内径(単位 センチメートル) | 鋼板又は鋼管(単位 ミリメートル) |
| 六十未満 | 二 |
| 六十以上百二十未満 | 二・五 |
| 百二十以上二百未満 | 三・五 |
| 二百以上 | 五 |
the main parts to be made of steel plates or steel pipes with a thickness equal to or more than that listed in the right column of the following table in accordance with the inner diameter listed in the left column of the same table;
| Inner diameter (unit: cm) | Steel plate or steel pipe (unit: mm) |
| Less than 60 | 2 |
| 60 or more and less than 120 | 2.5 |
| 120 or more and less than 200 | 3.5 |
| 200 or more | 5 |
主要部分の鋼板又は鋼管の接合方法は、溶接、びよう接又はボルト締めによるものであること。
the method of joining steel plates or steel pipes of the main parts to be welding, or using rivet joints or bolt joints; and
アセチレンと空気との混合ガスを排出するためのガス逃がし弁又はコツクを備えていること。
to be equipped with a gas escape valve or a cock to discharge a mixed gas of acetylene and air;
発生器から送り出された後、圧縮装置により圧縮されたアセチレンのためのガスだめにあつては、前号に定めるところによるほか、次に定める安全弁及び圧力計を備えていること。
for the gas holder for acetylene that is compressed by a compressor after being fed from the generator, in addition to compliance with the requirements set forth in the preceding item, to be equipped with a safety valve and a pressure gauge as prescribed in the following sub-items:
安全弁
safety valve
ガスだめ内の圧力が百四十キロパスカルに達しないうちに作動し、かつ、その圧力が常用圧力から十キロパスカル低下するまでの間に閉止するものであること。
being one that operates before the pressure inside the gas holder reaches 140 kPa and closes by the time the pressure falls by 10 kPa from the normal working pressure;
発生器が最大量のアセチレンを発生する場合において、ガスだめ内の圧力を百五十キロパスカル未満に保持する能力を有するものであること。
having the capacity to keep the pressure inside the gas holder at less than 150 kPa when the generator generates the maximum quantity of acetylene;
圧力計
pressure gauge
目もり盤の径は、定置式のガスだめに取り付けるものにあつては七十五ミリメートル以上、移動式のガスだめに取り付けるものにあつては五十ミリメートル以上であること。
having a dial with a diameter of 75 mm or more for a gauge attached to a stationary gas holder, and 50 mm or more for a gauge attached to a portable gas holder;
目もり盤の最大指度は、常用圧力の一・五倍以上、かつ、五百キロパスカル以下の圧力を示すものであること。
having a dial whose maximum reading indicates a pressure of 1.5 times the normal working pressure or more and 500 kPa or less;
目もりには、常用圧力を示す位置に見やすい表示がされているものであること。
having a conspicuous indication on the scale at the position indicating the normal working pressure;
ガスだめ、清浄器、導管等のアセチレンと接触する部分は、銅又は銅を七十パーセント以上含有する合金を使用しないものであること。
for the parts of the gas holder, purifiers, acetylene distributing lines, etc., which contact acetylene, copper or an alloy containing 70% or more copper are not used.
事業者は、前項のアセチレン溶接装置以外のアセチレン溶接装置の清浄器、導管等でアセチレンが接触するおそれのある部分には、銅を使用してはならない。
The employer must not use copper for the parts of the purifiers, acetylene distributing lines etc., of acetylene welding equipment other than those set forth in the preceding paragraph that is likely to come in contact with acetylene.
事業者は、アセチレン溶接装置については、その吹管ごとに安全器を備えなければならない。ただし、主管に安全器を備え、かつ、吹管に最も近接した分岐管ごとに安全器を備えたときは、この限りでない。
As regards acetylene welding equipment, the employer must provide safety equipment for each blowpipe; provided, however, that this does not apply when safety equipment is provided to the main pipe and for each branch pipe nearest to the blowpipes.
事業者は、ガスだめが発生器と分離しているアセチレン溶接装置については、発生器とガスだめの間に安全器を設けなければならない。
As regards acetylene welding equipment in which the gas holder and the generator are separated, the employer must provide safety equipment between the generator and the gas holder.
事業者は、カーバイドのかすだめについては、これを安全な場所に設け、その構造は、次に定めるところに適合するものとしなければならない。ただし、出張作業等で、移動式のアセチレン溶接装置を使用するときは、この限りでない。
The employer must install a sludge pit at a safe place and its structure must conform to the requirements set forth in the following items; provided, however, that this does not apply to mobile acetylene welding equipment used for outwork:
れんが又はコンクリート等を使用すること。
bricks or concrete is to be used; and
容積は、カーバイドてん充器の三倍以上とすること。
the capacity of the sludge pit is to be three times or more of the carbide charging device.
事業者は、令第一条第二号のガス集合装置(以下「ガス集合装置」という。)については、火気を使用する設備から五メートル以上離れた場所に設けなければならない。
As regards a gas manifold set forth in Article 1, item (ii) of the Order (hereinafter referred to as "gas manifolds"), the employer must install them in a place at a distance of 5 m or more from equipment using fire.
事業者は、ガス集合装置で、移動して使用するもの以外のものについては、専用の室(以下「ガス装置室」という。)に設けなければならない。
As regards a gas manifolds other than those movable, the employer must install them in a dedicated room (hereinafter referred to as "gas manifold room").
事業者は、ガス装置室の壁とガス集合装置との間隔については、当該装置の取扱い、ガスの容器の取替え等をするために十分な距離に保たなければならない。
As regards the space between the wall of the gas manifold room and a gas manifold, the employer must keep sufficient space for handling of the device, exchanging of a gas cylinder, etc.
事業者は、ガス装置室については、次に定めるところに適合するものとしなければならない。
As regards a gas manifold room, the employer must conform to the following requirements:
ガスが漏えいしたときに、当該ガスが滞留しないこと。
the gas does not stagnate when there is leakage of gas;
屋根及び天井の材料が軽い不燃性の物であること。
to be constructed with a roof and a ceiling made of lightweight and incombustible materials; and
壁の材料が不燃性の物であること。
to be constructed with a wall made of incombustible materials.
事業者は、令第一条第二号に掲げるガス集合溶接装置(以下「ガス集合溶接装置」という。)の配管については、次に定めるところによらなければならない。
As regards the piping of the gas welding equipment using manifolds listed in Article 1, item (ii) of the Order (hereinafter referred to as "the gas welding equipment using manifolds"), the employer must conform to the requirements set forth in the following items:
フランジ、バルブ、コツク等の接合部には、ガスケツトを使用し、接合面を相互に密接させる等の措置を講ずること。
for the joining part of a flange, a valve, a cock, etc., to take measures such as using gaskets and bringing the joining surfaces into close contact with each other; and
主管及び分岐管には、安全器を設けること。この場合において、一の吹管について、安全器が二以上になるようにすること。
to install a safety equipment for the main pipe and branch pipes. In this case, to install two or more safety equipment for each blowpipe.
事業者は、溶解アセチレンのガス集合溶接装置の配管及び附属器具には、銅又は銅を七十パーセント以上含有する合金を使用してはならない。
The employer must not use copper or an alloy containing 70% or more copper for the piping of the gas welding equipment using manifolds for dissolved acetylene and its accessories.
事業者は、アセチレン溶接装置を用いて金属の溶接、溶断又は加熱の作業を行うときは、次に定めるところによらなければならない。
When carrying out the work of welding, fusing or heating metals using acetylene welding equipment, the employer must comply with the requirements set forth in the following items:
発生器(移動式のアセチレン溶接装置の発生器を除く。)の種類、型式、製作所名、毎時平均ガス発生算定量及び一回のカーバイド送給量を発生器室内の見やすい箇所に掲示すること。
to display the type, model, manufacturer's name, calculated quantity of hourly average gas generation, and the quantity of carbide fed in one lot of generators (excluding the gas generators of portable acetylene welding equipment) at a readily visible location in the generator room;
発生器室には、係員のほかみだりに立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止するとともに、表示以外の方法により禁止したときは、発生器室が立入禁止である旨を見やすい箇所に表示すること。
to prohibit persons other than the staff in charge from entering the generator room without reason by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that the generator room is subject to the prohibition of entry;
発生器から五メートル以内又は発生器室から三メートル以内の場所では、喫煙、火気の使用又は火花を発するおそれのある行為について、禁止する旨を見やすい箇所に表示することその他の方法により禁止するとともに、表示以外の方法により禁止したときは、当該場所において喫煙、火気の使用又は火花を発するおそれのある行為が禁止されている旨を見やすい箇所に表示すること。
in a place within 5 m of the generator or within 3 m of the generator room, to prohibit smoking, the use of fire or acts that are liable to produce sparks by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that smoking, the use of fire or acts that are liable to produce sparks are prohibited at that place;
導管には、酸素用とアセチレン用との混同を防ぐための措置を講ずること。
to take measures to prevent confusion between supply lines for oxygen from those for acetylene;
アセチレン溶接装置の設置場所には、適当な消火設備を備えること。
to provide appropriate fire extinguishing equipment at places where acetylene welding equipment is installed;
移動式のアセチレン溶接装置の発生器は、高温の場所、通風又は換気の不十分な場所、振動の多い場所等に据え付けないこと。
to not install the generators for portable acetylene welding equipment at places where the temperature is high, ventilation or airing is insufficient, or where there is much vibration, etc.; and
当該作業を行う者に保護眼鏡及び保護手袋を着用させること。
to have the person engaging in the work wear eye protector and protective gloves.
事業者は、ガス集合溶接装置を用いて金属の溶接、溶断又は加熱の作業を行うときは、次に定めるところによらなければならない。
When carrying out the work of welding, fusing or heating metal using the gas welding equipment using manifolds, the employer must comply with the requirements set forth in the following items:
使用するガスの名称及び最大ガス貯蔵量を、ガス装置室の見やすい箇所に掲示すること。
to display the name of the gas used and the maximum quantity of gas stored at a readily visible location in the gas manifold room;
ガスの容器を取り替えるときは、ガス溶接作業主任者に立ち合わせること。
to have the operations supervisor of gas welding attend when exchanging a gas cylinder;
ガス装置室には、係員のほかみだりに立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止するとともに、表示以外の方法により禁止したときは、ガス装置室が立入禁止である旨を見やすい箇所に表示すること。
to prohibit persons other than the staff in charge from entering the gas manifold room without reason by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that the gas manifold room is subject to the prohibition of entry;
ガス集合装置から五メートル以内の場所では、喫煙、火気の使用又は火花を発するおそれのある行為について、禁止する旨を見やすい箇所に表示することその他の方法により禁止するとともに、表示以外の方法により禁止したときは、当該場所において喫煙、火気の使用又は火花を発するおそれのある行為が禁止されている旨を見やすい箇所に表示すること。
in a place within 5 m of the gas manifolds, to prohibit smoking, the use of fire or acts that are liable to produce sparks by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that smoking, the use of fire or acts that are liable to produce sparks are prohibited at that place;
バルブ、コック等の操作要領及び点検要領をガス装置室の見やすい箇所に表示すること。
to display the guidelines of operation and of inspection of a valve, a cock, etc., at a readily visible location in the gas manifold room;
導管には、酸素用とガス用との混同を防止するための措置を講ずること。
to take measures to prevent confusion between supply lines for oxygen from those for gas;
ガス集合装置の設置場所に適当な消火設備を設けること。
to install appropriate fire extinguishing equipment at the places where a gas manifold is installed; and
当該作業を行う者に保護眼鏡及び保護手袋を着用させること。
to have the person engaging in the work wear eye protector and protective gloves.