事業者は、火炉その他多量の高熱物を取り扱う設備については、火災を防止するため必要な構造としなければならない。
As regards furnace and other facilities handling a large quantity of high-temperature substances, the employer must ensure that they have a structure necessary to prevent fires.
条文、法令、用語を検索します
この条文はまだされていません2027年4月1日から施行予定(4か月後)
いまの条文を読む →第四章 爆発、火災等の防止(第二百四十八条から第二百六十二条まで)
労働安全衛生規則の一部を改正する省令(令和七年厚生労働省令第十二号)による改正後の条文です。変わる言葉に印をつけています。
本則は章ごとのページで読みます。長い章は、さらに条のまとまりごとに分けています。本則の全条文と、この改正が変える附則・別表を示します。この改正が触れていない附則や別表は、いま施行されている条文のページでご覧ください。
事業者は、火炉その他多量の高熱物を取り扱う設備については、火災を防止するため必要な構造としなければならない。
As regards furnace and other facilities handling a large quantity of high-temperature substances, the employer must ensure that they have a structure necessary to prevent fires.
事業者は、水蒸気爆発を防止するため、溶融した高熱の鉱物(以下「溶融高熱物」という。)を取り扱うピツト(高熱の鉱さいを水で処理するものを除く。)については、次の措置を講じなければならない。
In order to prevent steam explosions, the employer must take the following measures for melted high-temperature minerals (hereinafter referred to as "melted high-temperature substance") handling pits (excluding those processing high-temperature slag with water):
地下水が内部に浸入することを防止できる構造とすること。ただし、内部に滞留した地下水を排出できる設備を設けたときは、この限りでない。
to have the structure enabling to prevent underground water from penetrating inside the pit; provided, however, that this does not apply when the pits are equipped with facilities that can discharge the underground water stagnated inside the pit;
作業用水又は雨水が内部に浸入することを防止できる隔壁その他の設備を周囲に設けること。
to install partitions or other equipment that can prevent work-use water or rain water from penetrating inside the pit.
事業者は、水蒸気爆発を防止するため、溶融高熱物を取り扱う設備を内部に有する建築物については、次の措置を講じなければならない。
In order to prevent steam explosions, the employer must take the following measures for buildings which have facilities handling melted high-temperature substances inside:
床面は、水が滞留しない構造とすること。
to have floor surface that is structured to prevent the stagnation of water; and
屋根、壁、窓等は、雨水が浸入することを防止できる構造とすること。
to have the roof, wall, window, etc., that is structured to prevent rainwater from penetrating inside the building.
事業者は、溶融高熱物を取り扱う作業(高熱の鉱さいを水で処理する作業及び高熱の鉱さいを廃棄する作業を除く。)を行なうときは、水蒸気爆発を防止するため、第二百四十九条のピツト、前条の建築物の床面その他当該溶融高熱物を取り扱う設備について、これらに水が滞留し、又はこれらが水により湿潤していないことを確認した後でなければ、当該作業を行なつてはならない。
When the work of handling melted high-temperature substances (excluding work of processing high-temperature slag with water and work of disposing the slag) is carried out, in order to prevent steam explosions, the employer must not carry out the work unless having confirmed that the pit set forth in Article 249, the floor surface of building set forth in the preceding Article, and other facilities handling melted high-temperature substance are free of stagnant water, or are not wet.
事業者は、水蒸気爆発を防止するため、高熱の鉱さいを水で処理し、又は廃棄する場所については、次の措置を講じなければならない。ただし、水砕処理を行なうときは、この限りでない。
As regards places where high-temperature slag is processed with water, or is disposed, in order to prevent steam explosions, the employer must take the following measures; provided, however, this does not apply when water granulation process is performed:
高熱の鉱さいを水で処理し、又は廃棄する場所は、排水が良いところとすること。
the place where high-temperature slag is processed with water, or is disposed, is to be a place with good drainage; and
高熱の鉱さいを廃棄する場所には、その場所である旨の表示をすること。
the place where high-temperature slag is disposed is to indicate that fact.
事業者は、高熱の鉱さいを水で処理し、又は廃棄する作業を行なうときは、水蒸気爆発を防止するため、前条の場所に水が滞留していないことを確認した後でなければ、当該作業を行なつてはならない。ただし、水砕処理を行なうときは、この限りでない。
When carrying out the work of processing high-temperature slag with water, or work of disposing the slag, in order to prevent steam explosions, the employer must not carry out the work unless having confirmed that the places set forth in the preceding Article are free of stagnant water; provided, however, that this does not apply when water granulation process is performed.
事業者は、金属の溶解炉に金属くずを入れる作業を行なうときは、水蒸気爆発その他の爆発を防止するため、当該金属くずに水、火薬類、危険物、密閉された容器等がはいつていないことを確認した後でなければ、当該作業を行なつてはならない。
When carrying out the work of putting metal scraps in a metal melting furnace, in order to prevent steam explosions and other explosions, the employer must not carry out the work unless having confirmed that the metal scraps do not contain water, gunpowder, dangerous goods, airtight containers, etc.
事業者は、溶鉱炉、溶銑炉又はガラス溶解炉その他多量の高熱物を取り扱う作業を行なう場所については、当該高熱物の飛散、流出等による火傷その他の危険を防止するため、適当な措置を講じなければならない。
As regards a blast furnace, a cupola, glass melting furnace and other places where the work of handling a large quantity of high-temperature substances is carried out, the employer must take appropriate measures in order to prevent burns or other dangers due to the scattering, outflow, etc., of the high-temperature substances.
事業者は、前項の場所には、火傷その他の危険を防止するため、適当な保護具を備えなければならない。
The employer must provide the places set forth in the preceding paragraph with appropriate personal protective equipment in order to prevent burns and other dangers.
労働者は、第一項の作業を行なうときは、前項の保護具を使用しなければならない。
A worker, when carrying out the work set forth in paragraph (1), must use the personal protective equipment set forth in the preceding paragraph.
事業者は、危険物を製造し、又は取り扱うときは、爆発又は火災を防止するため、次に定めるところによらなければならない。
When manufacturing or handling dangerous goods, the employer must comply with the following requirements in order to prevent explosions or fires:
爆発性の物(令別表第一第一号に掲げる爆発性の物をいう。)については、みだりに、火気その他点火源となるおそれのあるものに接近させ、加熱し、摩擦し、又は衝撃を与えないこと。
as regards explosive substances (meaning those listed in the Appended Table 1, item (1) of the Order), to not bring them close to fire or other things that are likely to become a fire source, or heat, rub them or give a shock to them without reason;
発火性の物(令別表第一第二号に掲げる発火性の物をいう。)については、それぞれの種類に応じ、みだりに、火気その他点火源となるおそれのあるものに接近させ、酸化をうながす物若しくは水に接触させ、加熱し、又は衝撃を与えないこと。
as regards combustible substances (meaning those listed in the Appended Table 1, item (2) of the Order), to not bring them close to fire or other things that are likely to become a fire source, or make them come into contact with substances that accelerate oxidation or with water, heat them, or give a shock to them, in accordance with their types, without reason;
酸化性の物(令別表第一第三号に掲げる酸化性の物をいう。以下同じ。)については、みだりに、その分解がうながされるおそれのある物に接触させ、加熱し、摩擦し、又は衝撃を与えないこと。
as regards oxidizing substances (meaning those listed in the Appended Table 1, item (3) of the Order; the same applies hereinafter), to not make them come into contact with substances which are likely to accelerate decomposition, or heat, rub them, or give a shock to them without reason;
引火性の物(令別表第一第四号に掲げる引火性の物をいう。以下同じ。)については、みだりに、火気その他点火源となるおそれのあるものに接近させ、若しくは注ぎ、蒸発させ、又は加熱しないこと。
as regards inflammable substances (meaning those listed in the Appended Table 1, item (4) of the Order; the same applies hereinafter), to not bring them close to fire or other things that are likely to become a fire source, or pour them, make them evaporate, or heat them without reason; and
危険物を製造し、又は取り扱う設備のある場所を常に整理整とんし、及びその場所に、みだりに、可燃性の物又は酸化性の物を置かないこと。
to keep the places that have facilities that manufacture or handle the dangerous goods clean and organized at all times, and to not place flammable or oxidizing substances in the places without reason.
労働者は、前項の場合には、同項各号に定めるところによらなければならない。
A worker, in the case referred to in the preceding paragraph, must comply with the requirements set forth in each item of the same paragraph.
事業者は、危険物を製造し、又は取り扱う作業(令第六条第二号又は第八号に掲げる作業を除く。)を行なうときは、当該作業の指揮者を定め、その者に当該作業を指揮させるとともに、次の事項を行なわせなければならない。
When carrying out the work of manufacturing or handling dangerous goods (excluding the work listed in Article 6, item (ii) or item (viii) of the Order), the employer must designate a supervisor for the work, and have the supervisor direct the work as well as carry out the following matters:
危険物を製造し、又は取り扱う設備及び当該設備の附属設備について、随時点検し、異常を認めたときは、直ちに、必要な措置をとること。
to inspect as needed the facilities and their attached facilities that manufacture or handle the dangerous goods, and when having found an abnormality, to immediately take necessary measures;
危険物を製造し、又は取り扱う設備及び当該設備の附属設備がある場所における温度、湿度、遮光及び換気の状態等について、随時点検し、異常を認めたときは、直ちに、必要な措置をとること。
to inspect as needed the temperature, humidity, conditions of shading of light and ventilation, etc., in the place that has the facilities and their attached facilities where the dangerous goods are manufactured or handled, and when having found an abnormality, to immediately take necessary measures;
前各号に掲げるもののほか、危険物の取扱いの状況について、随時点検し、異常を認めたときは、直ちに、必要な措置をとること。
beyond what is set forth in the preceding items, to inspect as needed how dangerous goods are handled, and when having found an abnormality, to immediately take necessary measures; and
前各号の規定によりとつた措置について、記録しておくこと。
to keep records of the measures taken pursuant to the provisions of the preceding items.
事業者は、引火性の物又は可燃性ガス(令別表第一第五号に掲げる可燃性のガスをいう。以下同じ。)で液状のものを、ホースを用いて化学設備(配管を除く。)、タンク自動車、タンク車、ドラムかん等に注入する作業を行うときは、ホースの結合部を確実に締め付け、又ははめ合わせたことを確認した後でなければ、当該作業を行つてはならない。
When carrying out the work of pouring inflammable substances or combustible gas (meaning combustible gas listed in the Appended Table 1, item (5) of the Order; the same applies hereinafter) which are in liquid form into chemical facilities (excluding piping), a tank vehicle, a tank car, a drum, etc., using a hose, the employer must not carry out the work unless having confirmed that the joining parts of the hose are firmly fastened, or coupled.
労働者は、前項の作業に従事するときは、同項に定めるところによらなければ、当該作業を行なつてはならない。
A worker, when engaging in the work set forth in the preceding paragraph, must not carry out the work unless they conform to the requirements set forth in the same paragraph.
事業者は、ガソリンが残存している化学設備(危険物を貯蔵するものに限るものとし、配管を除く。次条において同じ。)、タンク自動車、タンク車、ドラムかん等に灯油又は軽油を注入する作業を行うときは、あらかじめ、その内部について、洗浄し、ガソリンの蒸気を不活性ガスで置換する等により、安全な状態にしたことを確認した後でなければ、当該作業を行つてはならない。
When carrying out the work of pouring kerosene or light oil into chemical facilities (limited to the facilities that store dangerous goods, and excluding piping; the same applies in the following Article), a tank vehicle, a tank car, a drum, etc., in which residual gasoline exists, the employer must not carry out the work unless having confirmed in advance, that the inside of the chemical facilities, etc., has been made safe by washing, replacing gasoline with inert gas, etc.
労働者は、前項の作業に従事するときは、同項に定めるところによらなければ、当該作業を行なつてはならない。
A worker, when engaging in the work set forth in the preceding paragraph, must not carry out the work unless they conform to the requirements set forth in the same paragraph.
事業者は、エチレンオキシド、アセトアルデヒド又は酸化プロピレンを化学設備、タンク自動車、タンク車、ドラムかん等に注入する作業を行うときは、あらかじめ、その内部の不活性ガス以外のガス又は蒸気を不活性ガスで置換した後でなければ、当該作業を行つてはならない。
When carrying out the work of pouring ethylene oxide, acetaldehyde or propylene oxide into chemical facilities, a tank vehicle, a tank car, a drum, etc., the employer must not carry out the work unless having replaced the gas or vapor other than inert gas in the chemical facilities, etc., by inert gas in advance.
事業者は、エチレンオキシド、アセトアルデヒド又は酸化プロピレンを化学設備、タンク自動車、タンク車、ドラムかん等に貯蔵するときは、常にその内部の不活性ガス以外のガス又は蒸気を不活性ガスで置換しておかなければならない。
When storing ethylene oxide, acetaldehyde or propylene oxide in chemical facilities, a tank vehicle, a tank car, a drum, etc., the employer must have the gas or vapor other than inert gas in the chemical facilities, etc., replaced by inert gas at all times.
事業者は、引火性の物の蒸気、可燃性ガス又は可燃性の粉じんが存在して爆発又は火災が生ずるおそれのある場所については、当該蒸気、ガス又は粉じんによる爆発又は火災を防止するため、通風、換気、除じん等の措置を講じなければならない。
As regards places where there is a risk of explosions or fires due to existing vapor of inflammable substances, flammable gas or flammable dust, the employer must take measures such as ventilation, airing, or removal of dust in order to prevent the explosions or fires.
事業者は、通風又は換気が不十分な場所において、可燃性ガス及び酸素(以下この条及び次条において「ガス等」という。)を用いて溶接、溶断又は金属の加熱の作業を行なうときは、当該場所におけるガス等の漏えい又は放出による爆発、火災又は火傷を防止するため、次の措置を講じなければならない。
When carrying out the work of welding, fusing, or heating metal using flammable gas and oxygen (hereinafter referred to as "gas, etc." in this Article and the following Article) at places where ventilation or airing is insufficient, the employer must take the following measures in order to prevent explosions, fires or burns due to leakage or discharge of gas, etc., at the places:
ガス等のホース及び吹管については、損傷、摩耗等によるガス等の漏えいのおそれがないものを使用すること。
as regards hoses and torches for gas, etc., those that do not have a risk of gas leakage due to their damages, wear, etc. are to be used;
ガス等のホースと吹管及びガス等のホース相互の接続箇所については、ホースバンド、ホースクリツプ等の締付具を用いて確実に締付けを行なうこと。
as regards connection of connecting parts between hoses and torches and between hoses of gas, etc., to fasten the parts securely with hose bands, hose clips, etc.;
ガス等のホースにガス等を供給しようとするときは、あらかじめ、当該ホースに、ガス等が放出しない状態にした吹管又は確実な止めせんを装着した後に行なうこと。
in supplying gas, etc., to hoses of gas, etc., to supply the gas, etc., after mounting on the hoses a blowpipe that is set so as not to discharge gas, etc., or a firm stop plug in advance;
使用中のガス等のホースのガス等の供給口のバルブ又はコツクには、当該バルブ又はコツクに接続するガス等のホースを使用する者の名札を取り付ける等ガス等の供給についての誤操作を防ぐための表示をすること。
to display an indication for preventing operational error of the supply of gas, etc., on the valve or cock of the supply inlet of gas, etc., of the hose being used, by attaching a name tag of the operator who uses the hose connected with the valve or cock, etc.;
溶断の作業を行なうときは、吹管からの過剰酸素の放出による火傷を防止するため十分な換気を行なうこと。
when carrying out the work of fusing, to provide sufficient ventilation to prevent burns due to the discharge of excessive oxygen from the blowpipes; and
作業の中断又は終了により作業箇所を離れるときは、ガス等の供給口のバルブ又はコツクを閉止してガス等のホースを当該ガス等の供給口から取りはずし、又はガス等のホースを自然通風若しくは自然換気が十分な場所へ移動すること。
when leaving the work place due to suspension or completion of the work, to shut the valve or cock of the supply inlet of gas, etc. and detach the hose of gas, etc. from that supply inlet of gas, etc., or move the hose of gas, etc. to a place where there is sufficient natural ventilation or natural air exchange.
労働者は、前項の作業に従事するときは、同項各号に定めるところによらなければ、当該作業を行なつてはならない。
A worker, when engaging in the work set forth in the preceding paragraph, must not carry out the work unless they conform to the requirements set forth in each item of the same paragraph.