Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 April 2027, in 4 months

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter II Construction Machines (Articles 188 to 194-13)

The law as Ministerial Order on the Arrangement, etc. of Related Ministerial Orders upon the Partial Enforcement of the Act Partially Amending the Industrial Safety and Health Act and the Working Environment Measurement Act (Ministry of Health, Labour and Welfare Order No. 29 of 2026) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Article 188第百八十八条

Measures to Be Taken When Hoisting Sheet Piles and Rods(矢板、ロッド等のつり上げ時の措置)
Article 188, paragraph (1)

When hoisting piles, sheet piles and rods, etc., with a pile driver or a boring machine, the employer must have the operator of the machine hoist piles in a manner that the hook part is located right under the sheave or the pulley block of the machine. The same applies to the case of hoisting a pile or sheet pile by providing a pile driver with a hoisting device such as a gin pole.

事業者は、くい打機又はボーリングマシンで、くい、矢板、ロッド等をつり上げるときは、その玉掛部が巻上げ用みぞ車又は滑車装置の直下になるようにつり上げさせなければならない。くい打機にジンポール等の物上げ装置を取り付けて、くい、矢板等をつり上げる場合においても、同様とする。

Article 189第百八十九条

Signals(合図)
Article 189, paragraph (1)

The employer must set fixed signals for the operation of a pile driver, a pile drawer or a boring machine, designate a person who gives the signals and have the person give the signals when operating the machine.

事業者は、くい打機、くい抜機又はボーリングマシンの運転について、一定の合図及び合図を行う者を定め、運転に当たつては、当該合図を使用させなければならない。

Article 189, paragraph (2)

An operator of a pile driver, a pile drawer or a boring machine must follow the signals set forth in the preceding paragraph.

くい打機、くい抜機又はボーリングマシンの運転者は、前項の合図に従わなければならない。

Article 190第百九十条

Supervision of the Work(作業指揮)
Article 190, paragraph (1)

When carrying out the work of assembling, disassembling, altering or transfer of a pile driver, a pile drawer or a boring machine, the employer must determine the method, procedures, etc., of the work, and make them known to the workers, designate a person who supervises the operation, and have the workers carry out the work under the direct supervision of the person.

事業者は、くい打機、くい抜機又はボーリングマシンの組立て、解体、変更又は移動を行うときは、作業の方法、手順等を定め、これらを労働者に周知させ、かつ、作業を指揮する者を指名して、その直接の指揮の下に作業を行わせなければならない。

Article 191第百九十一条

Transfer of Pile Drivers(くい打機等の移動)
Article 191, paragraph (1)

When transferring the legs of a pile driver or a pile drawer supported with stayed wires, etc., with the twin pillar, mast, etc., in a standing position, using power-driven winch or other machines, the employer must carry out the operation while braking the movement of the machine securely with a winch, tension blocks, etc., from the opposite side in order to prevent collapse due to the legs being dragged excessively.

事業者は、控えで支持するくい打機又はくい抜機の二本構、支柱等を建てたままで、動力によるウインチその他の機械を用いて、これらの脚部を移動させるときは、脚部の引過ぎによる倒壊を防止するため、反対側からテンシヨンブロツク、ウインチ等で、確実に制動しながら行なわせなければならない。

Article 192第百九十二条

Inspection(点検)
Article 192, paragraph (1)

When having assembled a pile driver, pile drawer or boring machine, the employer must inspect the following matters, and not allow the use of the machines unless having confirmed that there are no abnormalities:

事業者は、くい打機、くい抜機又はボーリングマシンを組み立てたときは、次の事項について点検し、異常がないことを確認してからでなければ、これを使用させてはならない。

Article 192, paragraph (1), item (i)

damage and slackness of joint parts of the machine;

機体の緊結部のゆるみ及び損傷の有無

Article 192, paragraph (1), item (ii)

fitted state of the hoisting wire rope, sheave, and pulley block;

巻上げ用ワイヤロープ、みぞ車及び滑車装置の取付状態

Article 192, paragraph (1), item (iii)

functions of the brake and ratchets of hoisting device;

巻上げ装置のブレーキ及び歯止め装置の機能

Article 192, paragraph (1), item (iv)

installation status of a winch; and

ウインチの据付状態

Article 192, paragraph (1), item (v)

for a pile driver or a pile drawer of which the top part is secured with stays, the method of fixing the stays and the firmness of the stays.

控えで頂部を安定させるくい打機又はくい抜機にあつては、控えのとり方及び固定の状態

Article 193第百九十三条

Measures to Be Taken in the Case of Slackening the Bracing Wires(控線をゆるめる場合の措置)
Article 193, paragraph (1)

When slackening the bracing wires (including temporary bracing wires, hereinafter the same applies in this Article) of a pile driver or a pile drawer, the employer must take appropriate measures such as using tension blocks or winches in order to prevent letting the load exceed the limit of the load the workers engaged in the slackening operation are able to easily support.

事業者は、くい打機又はくい抜機の控線(仮控線を含む。以下この条において同じ。)をゆるめるときは、テンシヨンブロツク又はウインチを用いる等適当な方法により、控線をゆるめる労働者に、その者が容易に支持することができる限度をこえる荷重がかからないようにさせなければならない。

Article 194第百九十四条

Prevention of Damage to Gas Pipes(ガス導管等の損壊の防止)
Article 194, paragraph (1)

When the work using a pile driver or boring machine is carried out and there is a risk of endangering workers due to damage of gas pipes, underground electric lines and other underground structures (hereinafter referred to as "gas pipes, etc." in this Article), the employer must in advance, conduct investigation of the workplace by inquiring the existence of the gas pipes, etc., and confirming their conditions to the person administrating the gas pipes, etc., and take measures in conformity with the matters they have come to know by the investigation.

事業者は、くい打機又はボーリングマシンを使用して作業を行う場合において、ガス導管、地中電線路その他地下に存する工作物(以下この条において「ガス導管等」という。)の損壊により労働者に危険を及ぼすおそれのあるときは、あらかじめ、作業箇所について、ガス導管等の有無及び状態を当該ガス導管等を管理する者に確かめる等の方法により調査し、これらの事項について知り得たところに適応する措置を講じなければならない。

Article 194-2第百九十四条の二

Measures to Be Taken when Attaching Rods(ロッドの取付時等の措置)
Article 194-2, paragraph (1)

When attaching or removing the rod or bit, etc., of a boring machine, the employer must securely cut off the power rotating the rod, etc., by such means as fixing the clutch lever with a stopper.

事業者は、ボーリングマシンのロッド、ビット等を取り付け又は取り外すときは、クラッチレバーをストッパーで固定する等によりロッド等を回転させる動力を確実に遮断しなければならない。

Article 194-2, paragraph (2)

When removing a rod or attaching or removing a bit, etc., from a boring machine, the employer must securely hold the rod with the rod holder, etc.

事業者は、ボーリングマシンのロッドを取り外すとき及びビット等を取り付け又は取り外すときは、ロッドをロッドホルダー等により確実に保持しなければならない。

Article 194-3第百九十四条の三

Fixing the Hose for a Water Swivel(ウォータースイベル用ホースの固定等)
Article 194-3, paragraph (1)

As regards a hose to be connected to the water swivel of a boring machine, the employer must take measures such as fixing the hose to a tower in order to prevent workers from danger due to the hose being trapped into the rotating parts of the rod, etc.

事業者は、ボーリングマシンのウォータースイベルに接続するホースについては、当該ホースがロッド等の回転部分に巻き込まれることによる労働者の危険を防止するため、当該ホースをやぐらに固定する等の措置を講じなければならない。

Section 2-2 Jack-type Lifting Machines第二節の二 ジャッキ式つり上げ機械

Article 194-4第百九十四条の四

Holding Mechanisms(保持機構等)
Article 194-4, paragraph (1)

The employer must not use a jack-type lifting machine for construction work unless the machine falls under the following requirements:

事業者は、建設工事の作業において使用するジャッキ式つり上げ機械については、次の要件に該当するものでなければ、使用してはならない。

Article 194-4, paragraph (1), item (i)

having the necessary strength in accordance with the purpose of use;

使用の目的に適応した必要な強度を有すること。

Article 194-4, paragraph (1), item (ii)

for holding mechanisms, having the necessary capability to hold a wire rope, etc.;

保持機構については、ワイヤロープ等を保持するために必要な能力を有すること。

Article 194-4, paragraph (1), item (iii)

having the mechanism to prevent simultaneous opening of all the holding mechanisms; and

すべての保持機構が同時に開放されることを防止する機構を有していること。

Article 194-4, paragraph (1), item (iv)

being free from marked damage, wear, deformation or corrosion.

著しい損傷、磨耗、変形又は腐食のないものであること。

Article 194-5第百九十四条の五

Work Plan(作業計画)
Article 194-5, paragraph (1)

When carrying out the work of lifting or lowering the load using a jack-type lifting machine in carrying out construction, the employer must establish in advance a work plan and carry out the work according to the work plan.

事業者は、建設工事の作業を行う場合において、ジャッキ式つり上げ機械を用いて荷のつり上げ、つり下げ等の作業を行うときは、あらかじめ、作業計画を定め、かつ、当該作業計画により作業を行わなければならない。

Article 194-5, paragraph (2)

The work plan set forth in the preceding paragraph must indicate the following matters:

前項の作業計画は、次の事項が示されているものでなければならない。

Article 194-5, paragraph (2), item (i)

the method and procedures of the work;

作業の方法及び順序

Article 194-5, paragraph (2), item (ii)

the method for preventing the jack-type lifting machine to be used from collapsing or overturning;

使用するジャッキ式つり上げ機械の崩壊及び倒壊を防止するための方法

Article 194-5, paragraph (2), item (iii)

the method of installing the equipment for preventing the worker engaged in the work from danger of falling; and

作業に従事する労働者の墜落による危険を防止するための設備の設置の方法

Article 194-5, paragraph (2), item (iv)

the type and capability of the machinery or other such equipment to be used.

使用する機械等の種類及び能力

Article 194-5, paragraph (3)

When having established the work plan set forth in paragraph (1), the employer must make the matters set forth in each item of the preceding paragraph known to the workers concerned.

事業者は、第一項の作業計画を定めたときは、前項各号の事項について関係労働者に周知させなければならない。

Article 194-6第百九十四条の六

Work Using a Jack-type Lifting Machine(ジャッキ式つり上げ機械による作業)
Article 194-6, paragraph (1)

When carrying out the work of lifting, lowering, etc., of load using a jack-type lifting machine in carrying out construction work, the employer must take the following measures:

事業者は、建設工事の作業を行う場合において、ジャッキ式つり上げ機械を用いて荷のつり上げ、つり下げ等の作業を行うときは、次の措置を講じなければならない。

Article 194-6, paragraph (1), item (i)

to prohibit persons other than persons engaged in work concerned from entering the area where the work is carried out, by indicating the prohibition in a conspicuous place or by other methods;

当該作業を行う区域内に関係する作業従事者以外の者が立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止すること。

Article 194-6, paragraph (1), item (ii)

to suspend the work when dangers involved in carrying out the work are expected due to bad weather conditions such as strong wind, heavy rain or heavy snow;

強風、大雨、大雪等の悪天候のため、作業の実施について危険が予想されるときは、当該作業を中止すること。

Article 194-6, paragraph (1), item (iii)

when installing a jack-type lifting machine in facilities and temporary buildings etc., to fasten the machine securely using bolts, etc.; and

ジャッキ式つり上げ機械を施設、仮設物等に据え付けるときは、ボルト等を用いて当該ジャッキ式つり上げ機械を確実に固定させること。

Article 194-6, paragraph (1), item (iv)

when installing a jack-type lifting machine in facilities and temporary buildings, etc., to confirm the strength of the facilities and temporary buildings, etc., and to reinforce the strength when it is insufficient.

ジャッキ式つり上げ機械を施設、仮設物等に据え付けるときは、当該施設、仮設物等の耐力を確認し、耐力が不足しているときは、これを補強すること。

Article 194-7第百九十四条の七

Wearing of Safety Helmets(保護帽の着用)
Article 194-7, paragraph (1)

When the work of lifting and lowering of load is carried out using a jack-type lifting machine in carrying out construction work, the employer must have the worker engaging in the work wear a safety helmet in order to prevent workers from dangers due to objects that come flying or falling.

事業者は、建設工事の作業を行う場合において、ジャッキ式つり上げ機械を用いて荷のつり上げ、つり下げ等の作業を行うときは、物体の飛来又は落下による労働者の危険を防止するため、当該作業に従事する労働者に保護帽を着用させなければならない。

Article 194-7, paragraph (2)

The worker engaged in the work set forth in the preceding paragraph must wear the safety helmet set forth in the same paragraph.

前項の作業に従事する労働者は、同項の保護帽を着用しなければならない。

Section 2-3 Vehicle for Work at Height第二節の三 高所作業車

Article 194-8第百九十四条の八

Front and Rear Lamps(前照灯及び尾灯)
Article 194-8, paragraph (1)

As regards a vehicle for work at height (excluding those used for traveling; hereinafter the same applies in this Article) the employer must provide front and rear lamps for the vehicle; provided, however, that this does not apply to a vehicle for work at height used in the place where necessary illumination for safely carrying out the work is maintained.

事業者は、高所作業車(運行の用に供するものを除く。以下この条において同じ。)については、前照灯及び尾灯を備えなければならない。ただし、走行の作業を安全に行うため必要な照度が保持されている場所において使用する高所作業車については、この限りでない。

Article 194-9第百九十四条の九

Work Plan(作業計画)
Article 194-9, paragraph (1)

When carrying out the work using a vehicle for work at height (excluding the work of traveling on roads; hereinafter the same applies up to Article 194-11), the employer must establish in advance a work plan in conformity with the situation of the place pertaining to the work, the type and capability of the vehicle, and carry out the work according to the work plan.

事業者は、高所作業車を用いて作業(道路上の走行の作業を除く。以下第百九十四条の十一までにおいて同じ。)を行うときは、あらかじめ、当該作業に係る場所の状況、当該高所作業車の種類及び能力等に適応する作業計画を定め、かつ、当該作業計画により作業を行わなければならない。

Article 194-9, paragraph (2)

The work plan set forth in the preceding paragraph must indicate the work method using the vehicle for work at height.

前項の作業計画は、当該高所作業車による作業の方法が示されているものでなければならない。

Article 194-9, paragraph (3)

When having established the work plan set forth in paragraph (1), the employer must make the matters indicated pursuant to the provisions of the preceding paragraph known to the workers concerned.

事業者は、第一項の作業計画を定めたときは、前項の規定により示される事項について関係労働者に周知させなければならない。

Article 194-10第百九十四条の十

Work Director(作業指揮者)
Article 194-10, paragraph (1)

When carrying out the work using a vehicle for work at height, the employer must designate a supervisor for the work, and have the supervisor direct the work based on the work plan set forth in paragraph (1) of the preceding Article.

事業者は、高所作業車を用いて作業を行うときは、当該作業の指揮者を定め、その者に前条第一項の作業計画に基づき作業の指揮を行わせなければならない。

Article 194-11第百九十四条の十一

Prevention of Falling(転落等の防止)
Article 194-11, paragraph (1)

When carrying out the work using a vehicle for work at height, the employer must take necessary measures of projecting an outrigger, preventing uneven settling of the ground, and collapsing of a road shoulder in order to prevent workers from dangers due to overturning or falling of the vehicle.

事業者は、高所作業車を用いて作業を行うときは、高所作業車の転倒又は転落による労働者の危険を防止するため、アウトリガーを張り出すこと、地盤の不同沈下を防止すること、路肩の崩壊を防止すること等必要な措置を講じなければならない。

Article 194-12第百九十四条の十二

Signals(合図)
Article 194-12, paragraph (1)

When carrying out the work using a vehicle for work at height and operating a working floor at a place other than the working floor, the employer must take necessary measures of setting fixed signals, designating a person who gives the signals and having the person give the signals, etc., in order to ensure the communication between the worker on the working floor and the worker operating the working floor at a place other than the working floor.

事業者は、高所作業車を用いて作業を行う場合で、作業床以外の箇所で作業床を操作するときは、作業床上の労働者と作業床以外の箇所で作業床を操作する者との間の連絡を確実にするため、一定の合図を定め、当該合図を行う者を指名してその者に行わせる等必要な措置を講じなければならない。

Article 194-13第百九十四条の十三

Measures to Be Taken in the Case of Leaving the Operating Station(運転位置から離れる場合の措置)
Article 194-13, paragraph (1)

When the operator of a vehicle for work at height leaves the operating station (excluding the case where a worker carries out the work on the working floor or attempting to carry out the work), the employer must have the operator take the following measures:

事業者は、高所作業車の運転者が走行のための運転位置から離れるとき(作業床に労働者が乗つて作業を行い、又は作業を行おうとしている場合を除く。)は、当該運転者に次の措置を講じさせなければならない。

Article 194-13, paragraph (1), item (i)

to put the working floor in the lowest position; and

作業床を最低降下位置に置くこと。

Article 194-13, paragraph (1), item (ii)

to stop the prime mover and take measures of setting the brake securely to keep the machine in stopped state in order to prevent the vehicle for work at height from breaking into a run.

原動機を止め、かつ、停止の状態を保持するためのブレーキを確実にかける等の高所作業車の逸走を防止する措置を講ずること。

Article 194-13, paragraph (2)

The operator set forth in the preceding paragraph must take the measures listed in each item of the same paragraph when leaving the operating station for traveling of the vehicle for work at height.

前項の運転者は、高所作業車の走行のための運転位置から離れるときは、同項各号に掲げる措置を講じなければならない。

Article 194-13, paragraph (3)

When the operator of a vehicle for work at height leaves the operating station for traveling while a worker is on the working floor carrying out the work or attempting to carry out the work, the employer must have the operator take measures such as setting the brake securely to keep the machine in a stopped state.

事業者は、高所作業車の作業床に労働者が乗つて作業を行い、又は行おうとしている場合であつて、運転者が走行のための運転位置から離れるときは、当該高所作業車の停止の状態を保持するためのブレーキを確実にかける等の措置を講じさせなければならない。

Article 194-13, paragraph (4)

The operator set forth in the preceding paragraph must take the measures set forth in the same paragraph when leaving the operating station for traveling of the vehicle for work at height.

前項の運転者は、高所作業車の走行のための運転位置から離れるときは、同項の措置を講じなければならない。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy