Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 April 2027, in 4 months

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter II Construction Machines (Articles 151-175 to 164)

The law as Ministerial Order on the Arrangement, etc. of Related Ministerial Orders upon the Partial Enforcement of the Act Partially Amending the Industrial Safety and Health Act and the Working Environment Measurement Act (Ministry of Health, Labour and Welfare Order No. 29 of 2026) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Chapter II Construction Machines第二章 建設機械等

Section 1 Vehicle Type Construction Machines第一節 車両系建設機械

Subsection 1 General Provisions第一款 総則

Article 151-175第百五十一条の百七十五

Definitions, etc.(定義等)
Article 151-175, paragraph (1)

In this Section, the term "demolition machine" means a machine listed in Appended Table 7, item (vi) of the Order, which is power-driven and capable of self-propelling to unspecified places.

この節において解体用機械とは、令別表第七第六号に掲げる機械で、動力を用い、かつ、不特定の場所に自走できるものをいう。

Article 151-175, paragraph (2)

The machines specified by Order of the Ministry of Health, Labour and Welfare in Appended Table 7, item (vi), 2 of the Order are as follows:

令別表第七第六号2の厚生労働省令で定める機械は、次のとおりとする。

Article 151-175, paragraph (2), item (i)

steel frame cutting machine;

鉄骨切断機

Article 151-175, paragraph (2), item (ii)

concrete crusher;

コンクリート圧砕機

Article 151-175, paragraph (2), item (iii)

demolition grabbing machine.

解体用つかみ機

Subsection 1-2 Structure第一款の二 構造

Article 152第百五十二条

Provision of Front Lamp(前照灯の設置)
Article 152, paragraph (1)

The employer must provide a vehicle type construction machine with a front lamp; provided, however, that this does not apply to a vehicle type construction machine used at a place where necessary illumination for safely carrying out the work is maintained.

事業者は、車両系建設機械には、前照灯を備えなければならない。ただし、作業を安全に行うため必要な照度が保持されている場所において使用する車両系建設機械については、この限りでない。

Article 153第百五十三条

Head Guard(ヘッドガード)
Article 153, paragraph (1)

When using a vehicle type construction machine (limited to a bulldozer, a tractor shovel, a muck loader, a power shovel, a drag shovel and a demolition machine) in a place where there is a risk of endangering workers due to falling of rocks, etc., the employer must provide the vehicle type construction machine with a solid head guard.

事業者は、岩石の落下等により労働者に危険が生ずるおそれのある場所で車両系建設機械(ブル・ドーザー、トラクター・ショベル、ずり積機、パワー・ショベル、ドラグ・ショベル及び解体用機械に限る。)を使用するときは、当該車両系建設機械に堅固なヘッドガードを備えなければならない。

Subsection 2 Prevention of Dangers Pertaining to the Use of Vehicle Type Construction Machines第二款 車両系建設機械の使用に係る危険の防止

Article 154第百五十四条

Investigation and Record(調査及び記録)
Article 154, paragraph (1)

When carrying out the work using a vehicle type construction machine, the employer must investigate in advance the landform and condition of the nature of the soil, etc., of the place pertaining to the work in order to prevent workers from dangers due to falling of the machine, collapse of natural ground, etc., and record the result of the investigation.

事業者は、車両系建設機械を用いて作業を行なうときは、当該車両系建設機械の転落、地山の崩壊等による労働者の危険を防止するため、あらかじめ、当該作業に係る場所について地形、地質の状態等を調査し、その結果を記録しておかなければならない。

Article 155第百五十五条

Work Plan(作業計画)
Article 155, paragraph (1)

When carrying out the work using a vehicle type construction machine, the employer must establish in advance a work plan that conforms to what became known by the investigation pursuant to the provisions of the preceding Article, and carry out the work according to the work plan.

事業者は、車両系建設機械を用いて作業を行なうときは、あらかじめ、前条の規定による調査により知り得たところに適応する作業計画を定め、かつ、当該作業計画により作業を行なわなければならない。

Article 155, paragraph (2)

The work plan set forth in the preceding paragraph must indicate the following matters:

前項の作業計画は、次の事項が示されているものでなければならない。

Article 155, paragraph (2), item (i)

the type and capability of the vehicle type construction machine to be used;

使用する車両系建設機械の種類及び能力

Article 155, paragraph (2), item (ii)

the traveling route of the vehicle type construction machine; and

車両系建設機械の運行経路

Article 155, paragraph (2), item (iii)

the method of work by the vehicle type construction machine.

車両系建設機械による作業の方法

Article 155, paragraph (3)

When having established the work plan set forth in paragraph (1), the employer must make the matters set forth in items (ii) and (iii) of the preceding paragraph known to the workers concerned.

事業者は、第一項の作業計画を定めたときは、前項第二号及び第三号の事項について関係労働者に周知させなければならない。

Article 156第百五十六条

Speed Limit(制限速度)
Article 156, paragraph (1)

When carrying out the work using a vehicle type construction machine (excluding those with the maximum speed of 10 km/h or less), the employer must, in advance, set the appropriate speed limit for the vehicle type construction machine in accordance with the landform and conditions of nature of the soil, etc., of the place pertaining to the work and carry out the work by the set speed limit.

事業者は、車両系建設機械(最高速度が毎時十キロメートル以下のものを除く。)を用いて作業を行なうときは、あらかじめ、当該作業に係る場所の地形、地質の状態等に応じた車両系建設機械の適正な制限速度を定め、それにより作業を行なわなければならない。

Article 156, paragraph (2)

The operator of the vehicle type construction machine set forth in the preceding paragraph must not operate the vehicle type construction machine at a speed exceeding the speed limit set forth in the same paragraph.

前項の車両系建設機械の運転者は、同項の制限速度をこえて車両系建設機械を運転してはならない。

Article 157第百五十七条

Prevention of Falling, etc.(転落等の防止等)
Article 157, paragraph (1)

When carrying out the work using a vehicle type construction machine, the employer must take necessary measures for the operation route of the machine, such as preventing collapse of the shoulder and uneven settling of the ground, and maintaining the necessary width in order to prevent workers from dangers due to overturning or falling of the machine.

事業者は、車両系建設機械を用いて作業を行うときは、車両系建設機械の転倒又は転落による労働者の危険を防止するため、当該車両系建設機械の運行経路について路肩の崩壊を防止すること、地盤の不同沈下を防止すること、必要な幅員を保持すること等必要な措置を講じなければならない。

Article 157, paragraph (2)

When the work using a vehicle type construction machine is carried out at road shoulder, inclined place, etc., and there is a risk of endangering workers due to overturning or falling of the machine, the employer must place a guide, and have the person guide the machine.

事業者は、路肩、傾斜地等で車両系建設機械を用いて作業を行う場合において、当該車両系建設機械の転倒又は転落により労働者に危険が生ずるおそれのあるときは、誘導者を配置し、その者に当該車両系建設機械を誘導させなければならない。

Article 157, paragraph (3)

The operator of a vehicle type construction machine set forth in the preceding paragraph must follow the instructions given by the guide set forth in the same paragraph.

前項の車両系建設機械の運転者は、同項の誘導者が行う誘導に従わなければならない。

Article 157-2第百五十七条の二

Article 157-2, paragraph (1)

At a road shoulder, an inclined place, etc. where there is a risk of endangering the operator due to overturning or falling of a vehicle type construction machine, the employer must endeavor not to use a vehicle type construction machine other than one that has a roll-over protective structure and is equipped with a seat belt, and must endeavor to have the operator use the seat belt.

事業者は、路肩、傾斜地等であつて、車両系建設機械の転倒又は転落により運転者に危険が生ずるおそれのある場所においては、転倒時保護構造を有し、かつ、シートベルトを備えたもの以外の車両系建設機械を使用しないように努めるとともに、運転者にシートベルトを使用させるように努めなければならない。

Article 158第百五十八条

Prevention of Contact(接触の防止)
Article 158, paragraph (1)

When carrying out work using a vehicle type construction machine, the employer must prohibit a person engaged in work at the workshop from entering a place where there is a risk of danger due to contact with the vehicle type construction machine in operation, by indicating the prohibition in a conspicuous place or by other methods; provided, however, that this does not apply when the employer arranges a guide and has the person guide the machine.

事業者は、車両系建設機械を用いて作業を行うときは、運転中の車両系建設機械に接触することにより危険が生ずるおそれのある箇所に当該作業場において作業に従事する作業従事者が立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止しなければならない。ただし、誘導者を配置し、その者に当該車両系建設機械を誘導させるときは、この限りでない。

Article 158, paragraph (2)

The operator of the vehicle type construction machine set forth in the preceding paragraph must follow the instructions given by the guide set forth in the proviso of the same paragraph.

前項の車両系建設機械の運転者は、同項ただし書の誘導者が行う誘導に従わなければならない。

Article 159第百五十九条

Signals(合図)
Article 159, paragraph (1)

When placing a guide for operation of a vehicle type construction machine, the employer must set fixed signals and have the guide give the signals.

事業者は、車両系建設機械の運転について誘導者を置くときは、一定の合図を定め、誘導者に当該合図を行なわせなければならない。

Article 159, paragraph (2)

The operator of the vehicle type construction machine set forth in the preceding paragraph must follow the signals set forth in the same paragraph.

前項の車両系建設機械の運転者は、同項の合図に従わなければならない。

Article 160第百六十条

Measures to Be Taken in the Case of Leaving the Operating Station(運転位置から離れる場合の措置)
Article 160, paragraph (1)

When the operator of a vehicle type construction machine leaves the operating station, the employer must have the operator take the following measures:

事業者は、車両系建設機械の運転者が運転位置から離れるときは、当該運転者に次の措置を講じさせなければならない。

Article 160, paragraph (1), item (i)

to place the working device such as a bucket, ripper, etc., on the ground; and

バケツト、ジツパー等の作業装置を地上に下ろすこと。

Article 160, paragraph (1), item (ii)

to stop the prime mover and take measures such as setting the traveling brake in order to prevent the vehicle type construction machine from running away.

原動機を止め、かつ、走行ブレーキをかける等の車両系建設機械の逸走を防止する措置を講ずること。

Article 160, paragraph (2)

The operator set forth in the preceding paragraph must take measures listed in each item of the same paragraph when leaving the operating station of a vehicle type construction machine.

前項の運転者は、車両系建設機械の運転位置から離れるときは、同項各号に掲げる措置を講じなければならない。

Article 161第百六十一条

Transfer of Vehicle Type Construction Machine(車両系建設機械の移送)
Article 161, paragraph (1)

In the case of loading a vehicle type construction machine onto a truck, or unloading it from a truck, by self-propelling or towing for transferring the machine, when using loading plates, fills, etc., the employer must comply with the following requirements in order to prevent dangers due to overturning, falling, etc. of the vehicle type construction machine:

事業者は、車両系建設機械を移送するため自走又はけん引により貨物自動車に積卸しを行う場合において、道板、盛土等を使用するときは、当該車両系建設機械の転倒、転落等による危険を防止するため、次に定めるところによらなければならない。

Article 161, paragraph (1), item (i)

to load or unload the machine at a level and firm place;

積卸しは、平たんで堅固な場所において行なうこと。

Article 161, paragraph (1), item (ii)

when using a loading plate, to use the plate with sufficient length, width and strength, and fix it securely with appropriate incline; and

道板を使用するときは、十分な長さ、幅及び強度を有する道板を用い、適当なこう配で確実に取り付けること。

Article 161, paragraph (1), item (iii)

when using fills, a temporary stand, etc., to secure sufficient width and strength, and an appropriate incline.

盛土、仮設台等を使用するときは、十分な幅及び強度並びに適度な勾配を確保すること。

Article 162第百六十二条

Restriction on Riding(搭乗の制限)
Article 162, paragraph (1)

When carrying out work using a vehicle type construction machine, the employer must not have a person engaged in work at the workshop ride in any place other than the riding seat.

事業者は、車両系建設機械を用いて作業を行うときは、当該作業場において作業に従事する作業従事者を乗車席以外の箇所に乗せてはならない。

Article 163第百六十三条

Restriction of Use(使用の制限)
Article 163, paragraph (1)

When carrying out the work using a vehicle type construction machine, the employer must observe the stability, the maximum working load, etc., decided on the basis of its structure in order to prevent workers from dangers due to overturning or destruction of working devices such as a boom, an arm, etc.

事業者は、車両系建設機械を用いて作業を行うときは、転倒及びブーム、アーム等の作業装置の破壊による労働者の危険を防止するため、当該車両系建設機械についてその構造上定められた安定度、最大使用荷重等を守らなければならない。

Article 164第百六十四条

Restriction on the Use for Purpose Other than the Main Purpose(主たる用途以外の使用の制限)
Article 164, paragraph (1)

The employer must not use a vehicle type construction machine for purpose other than its main purpose such as to hoist loads by using a power shovel or to raise or lower workers in a clamshell.

事業者は、車両系建設機械を、パワー・ショベルによる荷のつり上げ、クラムシェルによる労働者の昇降等当該車両系建設機械の主たる用途以外の用途に使用してはならない。

Article 164, paragraph (2)

The provisions of the preceding paragraph do not apply to a case that falls under any of the following items:

前項の規定は、次のいずれかに該当する場合には適用しない。

Article 164, paragraph (2), item (i)

the case falling under all of the following sub-items, when the load lifting work is carried out:

荷のつり上げの作業を行う場合であつて、次のいずれにも該当するとき。

Article 164, paragraph (2), item (i), (a)

when it is unavoidable due to the nature of the work or necessary for the safe implementation of the work;

作業の性質上やむを得ないとき又は安全な作業の遂行上必要なとき。

Article 164, paragraph (2), item (i), (b)

when metal parts of a hook and a shackle or any other hoisting parts falling under all of the following conditions are fitted to the work device such as an arm or a bucket:

アーム、バケット等の作業装置に次のいずれにも該当するフック、シャックル等の金具その他のつり上げ用の器具を取り付けて使用するとき。

Article 164, paragraph (2), item (i), (b), (1)

those having sufficient strength in accordance with the load to be applied;

負荷させる荷重に応じた十分な強度を有するものであること。

Article 164, paragraph (2), item (i), (b), (2)

those that pose no risk of the lifted load falling from the device, owing to the use of a detachment prevention device, etc.;

外れ止め装置が使用されていること等により当該器具からつり上げた荷が落下するおそれのないものであること。

Article 164, paragraph (2), item (i), (b), (3)

those that pose no risk of coming off the working device;

作業装置から外れるおそれのないものであること。

Article 164, paragraph (2), item (ii)

when work other than lifting a load is carried out, and there is no risk of endangering the workers.

荷のつり上げの作業以外の作業を行う場合であつて、労働者に危険を及ぼすおそれのないとき。

Article 164, paragraph (3)

When carrying out the load lifting work falling under item (i), (a) and (b) of the preceding paragraph, the employer must take the following measures in order to prevent dangers due to contact between a person engaged in work at the workshop and the lifted load, falling of the lifted load, or overturning or falling of the vehicle type construction machine:

事業者は、前項第一号イ及びロに該当する荷のつり上げの作業を行う場合には、当該作業場において作業に従事する作業従事者とつり上げた荷との接触、つり上げた荷の落下又は車両系建設機械の転倒若しくは転落による危険を防止するため、次の措置を講じなければならない。

Article 164, paragraph (3), item (i)

to set fixed signals for load lifting work, as well as designate a person who gives the signals and have the person give the signals;

荷のつり上げの作業について一定の合図を定めるとともに、合図を行う者を指名して、その者に合図を行わせること。

Article 164, paragraph (3), item (ii)

to carry out the work on a level place;

平坦な場所で作業を行うこと。

Article 164, paragraph (3), item (iii)

to prohibit a person engaged in work from entering a place where there is a risk of danger due to contact with the lifted load or falling of the lifted load, by indicating the prohibition in a conspicuous place or by other methods;

つり上げた荷との接触又はつり上げた荷の落下により危険が生ずるおそれのある箇所に作業従事者が立ち入ることについて、禁止する旨を見やすい箇所に表示することその他の方法により禁止すること。

Article 164, paragraph (3), item (iv)

to not apply the load that exceeds the maximum load established in accordance with the structure and material of the vehicle type construction machine;

当該車両系建設機械の構造及び材料に応じて定められた負荷させることができる最大の荷重を超える荷重を掛けて作業を行わないこと。

Article 164, paragraph (3), item (v)

to use a wire rope falling under all of the following cases in the case where the wire rope is used as the slinging equipment:

ワイヤロープを玉掛用具として使用する場合にあつては、次のいずれにも該当するワイヤロープを使用すること。

Article 164, paragraph (3), item (v), (a)

those with a safety coefficient (meaning a safety coefficient prescribed in Article 213, paragraph (2) of the Crane Ordinance) of 6 or more;

安全係数(クレーン則第二百十三条第二項に規定する安全係数をいう。)の値が六以上のものであること。

Article 164, paragraph (3), item (v), (b)

those with less than 10% of the element wires (excluding filler wires) are cut in one strand;

ワイヤロープ一よりの間において素線(フィラ線を除く。)のうち切断しているものが十パーセント未満のものであること。

Article 164, paragraph (3), item (v), (c)

those with the reduction ratio of a diameter 7 % or less of the nominal diameter;

直径の減少が公称径の七パーセント以下のものであること。

Article 164, paragraph (3), item (v), (d)

those without kinks;

キンクしていないものであること。

Article 164, paragraph (3), item (v), (e)

those without marked deformation or corrosion;

著しい形崩れ及び腐食がないものであること。

Article 164, paragraph (3), item (vi)

to use a suspension chain falling under all of the following conditions when the suspension chain is used as the slinging equipment:

つりチェーンを玉掛用具として使用する場合にあつては、次のいずれにも該当するつりチェーンを使用すること。

Article 164, paragraph (3), item (vi), (a)

those with a safety coefficient (meaning a safety coefficient prescribed in Article 213-2, paragraph (2) of the Crane Ordinance) equal to or above the value listed in 1 or 2 below in accordance with the classification of chains listed in 1 or 2 below:

安全係数(クレーン則第二百十三条の二第二項に規定する安全係数をいう。)の値が、次の(1)又は(2)に掲げるつりチェーンの区分に応じ、当該(1)又は(2)に掲げる値以上のものであること。

Article 164, paragraph (3), item (vi), (a), (1)

Lifting chains that fall under all of the following: 4

Tensile strength (unit: N/mm2)Elongation (unit: percent)
400 or more but less than 63020
630 or more but less than 1,00017
1,000 or more15

次のいずれにも該当するつりチェーン 四

引張強さ(単位 ニュートン毎平方ミリメートル)伸び(単位 パーセント)
四百以上六百三十未満二十
六百三十以上千未満十七
千以上十五
Article 164, paragraph (3), item (vi), (a), (1), (i)

those with an elongation of 0.5 % or less when loaded with one half of the breaking load;

切断荷重の二分の一の荷重で引つ張つた場合において、その伸びが〇・五パーセント以下のものであること。

Article 164, paragraph (3), item (vi), (a), (1), (ii)

those whose tensile strength is 400 N/mm2 or more and whose elongation is, in accordance with the value of tensile strength listed in the left column of the following Table, equal to or more than the value listed in the right column of the same Table;

その引張強さの値が四百ニュートン毎平方ミリメートル以上であり、かつ、その伸びが、次の表の上欄に掲げる引張強さの値に応じ、それぞれ同表の下欄に掲げる値以上となるものであること。

Article 164, paragraph (3), item (vi), (a), (2)

Lifting chains that do not fall under (1): 5

(1)に該当しないつりチェーン 五

Article 164, paragraph (3), item (vi), (b)

those with the extension of 5 % or less of the length of the chain when it was manufactured;

伸びが、当該つりチェーンが製造されたときの長さの五パーセント以下のものであること。

Article 164, paragraph (3), item (vi), (c)

those with a reduction in section diameter of the links of 10 % or less of the section diameter of the links at the time of manufacture of the chain;

リンクの断面の直径の減少が、当該つりチェーンが製造されたときの当該リンクの断面の直径の十パーセント以下のものであること。

Article 164, paragraph (3), item (vi), (d)

those without cracks;

亀裂がないものであること。

Article 164, paragraph (3), item (vii)

when using something other than a wire rope or a lifting chain as the slinging equipment, to use the thing without marked damage or corrosion.

ワイヤロープ及びつりチェーン以外のものを玉掛用具として使用する場合にあつては、著しい損傷及び腐食がないものを使用すること。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy