Chapter I Prevention of Dangers Due to Machines (Articles 101 to 124)
The law as Ministerial Order on the Arrangement, etc. of Related Ministerial Orders upon the Partial Enforcement of the Act Partially Amending the Industrial Safety and Health Act and the Working Environment Measurement Act (Ministry of Health, Labour and Welfare Order No. 29 of 2026) leaves it, with the words it changes marked.
The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.
Part II Safety Standards第二編 安全基準
Chapter I Prevention of Dangers Due to Machines第一章 機械による危険の防止
Section 1 General Standards第一節 一般基準
Article 101第百一条
Prevention of Dangers Due to a Prime Mover and a Rotating Shaft(原動機、回転軸等による危険の防止)
Article 101, paragraph (1)
In a workshop where workers carry out work, the employer must provide a cover, an enclosure, a sleeve, an overbridge, etc. for the parts of a machine, such as a prime mover, a rotating shaft, a gear, a pulley and a belt, that are likely to endanger workers.
The employer must use the sunken head type or provide a cover for set-screws and other fixtures attached to a rotating shaft, a gear, a pulley, a flywheel, etc.
Prevention of Dangers Due to Cutting of a Belt(ベルトの切断による危険の防止)
Article 102, paragraph (1)
The employer must provide an enclosure under the belt for a belt that is located above a passage or a workplace and having a distance between pulleys of 3 m or more, width of 15 cm or more and speed of 10 m/sec or more.
The employer must provide a power cutting device such as a switch, a clutch or a belt shifter for each machine; provided, however, that this does not apply to a series of machines having a common power cutting device and not requiring manual supply or extraction of raw materials during the process of operation.
The employer must, when the machine set forth in the preceding paragraph is for the process of cutting, drawing, compressing, punching, bending or expressing, provide the power cutting device set forth in the same paragraph at a place where a person engaging in the processing work is able to operate it without leaving the work station.
The employer, as regards the power cutting device set forth in paragraph (1), must provide a device that can be easily operated and is not likely to unexpectedly activate due to contact, vibration, etc.
In starting the operation of a machine, when there is a risk of endangering workers, the employer must set fixed signals, designate a person who gives the signals, and have the person give the signals to the workers.
A worker must follow the signals set forth in the preceding paragraph.
労働者は、前項の合図に従わなければならない。
Article 105第百五条
Prevention of Dangers Due to Workpieces that Come Flying(加工物等の飛来による危険の防止)
Article 105, paragraph (1)
When there is a risk of endangering workers due to workpieces, etc. that are cut or broken and come flying, the employer must provide a cover or an enclosure for the machine that scatters the workpieces, etc.; provided, however, that this does not apply where providing a cover or an enclosure is difficult due to the nature of the work and the employer has had workers use personal protective equipment.
A worker, when having been ordered to use personal protective equipment in the case referred to in the proviso of the preceding paragraph, must use the equipment.
Prevention of Dangers Due to Chips that Come Flying(切削屑の飛来等による危険の防止)
Article 106, paragraph (1)
When there is a risk of endangering workers due to cutting chips coming flying, etc., the employer must provide a cover or an enclosure for the machine that generates the cutting chips; provided, however, that this does not apply where providing a cover or an enclosure is difficult due to the nature of the work and the employer has had workers use personal protective equipment.
A worker, when having been ordered to use personal protective equipment in the case referred to in the proviso of the preceding paragraph, must use the equipment.
Suspension of Operation, etc. in the Case of Cleaning, etc.(掃除等の場合の運転停止等)
Article 107, paragraph (1)
When work of cleaning, lubrication, inspection, repair or adjustment of a machine (excluding blade parts) is carried out and there is a risk of endangering workers, the employer must suspend the operation of the machine; provided, however, that this does not apply if the work has to be carried out during operation of the machine and measures such as providing a cover on dangerous parts have been taken.
When the employer has suspended the operation of the machine pursuant to the provisions of the preceding paragraph, the employer must take measures such as locking the starting device of the machine and attaching a sign plate to the starting device, to prevent persons other than the workers engaging in the work set forth in the same paragraph from operating the machine.
Suspension of Operation, etc. in the Case of Cleaning, etc. of Blade Parts(刃部の掃除等の場合の運転停止等)
Article 108, paragraph (1)
When carrying out the work of cleaning, inspecting, repairing, replacing or adjusting the blade parts of a machine, the employer must suspend the operation of the machine; provided, however, that this does not apply if there is no risk of endangering workers due to the structure of the machine.
When the employer has suspended the operation of the machine pursuant to the provisions of the preceding paragraph, the employer must take the measures of locking the starting device of the machine and attaching a plate to prevent persons other than the workers engaging in the work set forth in the same paragraph from operating the machine.
When removing chips or using cutting lubricants for the blade part of a machine during operation, the employer must have a worker use a brush or other appropriate tools.
A worker, when having been ordered to use a tool set forth in the preceding paragraph, must use the tool.
労働者は、前項の用具の使用を命じられたときは、これを使用しなければならない。
Article 108-2第百八条の二
Cover on Stroke Ends, etc.(ストローク端の覆い等)
Article 108-2, paragraph (1)
When the stroke ends of the ram of a shaper, a table of a grinding machine or a planer, etc. have a risk of endangering workers, the employer must take measures such as providing a cover, an enclosure or a railing to prevent that danger.
Prevention of Dangers Due to Wind-Up Roll(巻取りロール等の危険の防止)
Article 109, paragraph (1)
The employer must provide a cover or an enclosure, etc., for a wind-up roll or a coil of a paper, a cloth or a wire rope, etc., which has a risk of endangering the workers.
When there is a risk of getting hair or clothing of a worker working caught in a power-driven machine, the employer must have the worker wear appropriate work cap or work clothes.
A worker, when having been ordered to wear work cap or work clothes set forth in the preceding paragraph, must wear them.
労働者は、前項の作業帽又は作業服の着用を命じられたときは、これらを着用しなければならない。
Article 111第百十一条
Prohibition of the Use of Gloves(手袋の使用禁止)
Article 111, paragraph (1)
When there is a risk of getting fingers of the worker working caught in rotating blades of a drilling machine or a chamfering machine, the employer must not have the worker wear gloves.
In the case referred to in the preceding paragraph, when a worker has been prohibited to wear gloves, the worker must not wear them.
労働者は、前項の場合において、手袋の使用を禁止されたときは、これを使用してはならない。
Section 2 Machine Tools第二節 工作機械
Article 112第百十二条
Article 112, paragraph (1)
No English for this provision yet.
削除
Article 113第百十三条
Cover on Workpieces Protruding from Machine Tools(突出した加工物の覆い等)
Article 113, paragraph (1)
When a rotating workpiece protruding from a vertical lathe, a turret lathe, etc., has a risk of endangering workers, the employer must provide a cover, an enclosure, etc.
The employer must provide a cover or enclosure on the teeth of band saws (excluding woodworking band saws) other than the parts necessary for sawing and the band wheel.
Preventive Device for Contact with Teeth of a Circular Saw(丸のこ盤の歯の接触予防装置)
Article 115, paragraph (1)
The employer must provide a preventive device for contact with teeth of circular saws, etc. (excluding woodworking circular saws).
事業者は、丸のこ盤(木材加工用丸のこ盤を除く。)には、歯の接触予防装置を設けなければならない。
Article 116第百十六条
Prohibition of Riding on a Table of a Vertical Lathe, etc.(立旋盤等のテーブルへの搭乗の禁止)
Article 116, paragraph (1)
In a workshop where a vertical lathe, a planer, etc. is used, the employer must not allow a person engaged in work in the workshop to ride on a table of a vertical lathe, a planer, etc. during operation; provided, however, that this does not apply when a person on the table or a person placed at the operation panel is able to immediately stop the machine.
A person engaged in work in the workshop set forth in the preceding paragraph, excluding the case referred to in the proviso of the same paragraph, may not ride on a table of a vertical lathe, a planer, etc., during operation.
When a rotating grinding wheel has a risk of endangering workers, the employer must provide a cover; provided, however, that this does not apply to a grinding wheel with a diameter of less than 50 mm.
As regards a grinding wheel, the employer must make a test run for one minute or longer before commencing the work for the day and for three minutes or longer when the grinding wheel has been replaced.
Prohibition of Operation of a Grinding Wheel at a Speed Exceeding the Maximum Allowable Speed(研削といしの最高使用周速度をこえる使用の禁止)
Article 119, paragraph (1)
As regards a grinding wheel, the employer must not operate the grinding wheel at a speed exceeding the maximum allowable speed.
事業者は、研削といしについては、その最高使用周速度をこえて使用してはならない。
Article 120第百二十条
Prohibition of Use of Side Surfaces of a Grinding Wheel(研削といしの側面使用の禁止)
Article 120, paragraph (1)
The employer must not use the side surfaces of a grinding wheel except for a grinding wheel designed to use the side surfaces.
事業者は、側面を使用することを目的とする研削といし以外の研削といしの側面を使用してはならない。
Article 121第百二十一条
Cover on a Buff(バフの覆い)
Article 121, paragraph (1)
The employer must provide a cover on a buffing machine (excluding the buffing machine that use a cloth buff or a cork buff) other than the parts necessary for polishing.
Anti-Kickback Device for a Circular Saw(丸のこ盤の反ぱつ予防装置)
Article 122, paragraph (1)
The employer must provide a spreader or other anti-kickback device, etc., for a woodworking circular saw (excluding a cross cut circular saw and other circular saws that do not have the risk of endangering workers due to kickback of the wood).
Preventive Device for Contact with Teeth of a Circular Saw(丸のこ盤の歯の接触予防装置)
Article 123, paragraph (1)
The employer must provide a preventive device for contact with teeth of a woodworking circular saw (excluding a circular saw for lumber and that with an automatic feeding device).
The day a law or an amendment starts to apply. It is often months or years after promulgation, so that people have time to prepare. The Ministry of Justice's English usually says a law "comes into force" or "comes into effect", and sometimes calls the day its "enforcement date". Its "enforcement" more often means the word's other sense, carrying a law out, as in an Order for Enforcement (施行令), the Cabinet Order (政令) that sets out the details for carrying out an Act.
The Ministry of Justice's English of this passage has a slip, so the English shown is this site's correction of it. The Ministry printed:
The employer, as regards the power cutting device set forth in paragraph (1), provide a device that can be easily operated and is not likely to unexpectedly activate due to contact, vibration, etc.
Japanese Law Translation, Ministry of Justice
Translates the law as amended by Order of the Ministry of Health, Labour and Welfare No. 185 of 2006 (平成十八年厚生労働省令第百八十五号)
The Ministry of Justice's English of this passage has a slip, so the English shown is this site's correction of it. The Ministry printed:
When a rotating workpieces protruding from a vertical lath, a turret lath, etc., has a risk of endangering workers, the employer must provide a cover, an enclosure, etc.
Japanese Law Translation, Ministry of Justice
Translates the law as amended by Order of the Ministry of Health, Labour and Welfare No. 185 of 2006 (平成十八年厚生労働省令第百八十五号)