Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 April 2027, in 4 months

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter II Construction Machines (Articles 194-13 to 194-26)

The law as Ministerial Order Partially Amending the Ordinance on Industrial Safety and Health (Ministry of Health, Labour and Welfare Order No. 12 of 2025) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Article 194-13第百九十四条の十三

Measures to Be Taken in the Case of Leaving the Operating Station(運転位置から離れる場合の措置)
Article 194-13, paragraph (1)

When the operator of a vehicle for work at height leaves the operating station (excluding the case where a worker carries out the work on the working floor or attempting to carry out the work), the employer must have the operator take the following measures:

事業者は、高所作業車の運転者が走行のための運転位置から離れるとき(作業床に労働者が乗つて作業を行い、又は作業を行おうとしている場合を除く。)は、当該運転者に次の措置を講じさせなければならない。

Article 194-13, paragraph (1), item (i)

to put the working floor in the lowest position; and

作業床を最低降下位置に置くこと。

Article 194-13, paragraph (1), item (ii)

to stop the prime mover and take measures of setting the brake securely to keep the machine in stopped state in order to prevent the vehicle for work at height from breaking into a run.

原動機を止め、かつ、停止の状態を保持するためのブレーキを確実にかける等の高所作業車の逸走を防止する措置を講ずること。

Article 194-13, paragraph (2)

The operator set forth in the preceding paragraph must take the measures listed in each item of the same paragraph when leaving the operating station for traveling of the vehicle for work at height.

前項の運転者は、高所作業車の走行のための運転位置から離れるときは、同項各号に掲げる措置を講じなければならない。

Article 194-13, paragraph (3)

When the operator of a vehicle for work at height leaves the operating station for traveling while a worker is on the working floor carrying out the work or attempting to carry out the work, the employer must have the operator take measures such as setting the brake securely to keep the machine in a stopped state.

事業者は、高所作業車の作業床に労働者が乗つて作業を行い、又は行おうとしている場合であつて、運転者が走行のための運転位置から離れるときは、当該高所作業車の停止の状態を保持するためのブレーキを確実にかける等の措置を講じさせなければならない。

Article 194-13, paragraph (4)

The operator set forth in the preceding paragraph must take the measures set forth in the same paragraph when leaving the operating station for traveling of the vehicle for work at height.

前項の運転者は、高所作業車の走行のための運転位置から離れるときは、同項の措置を講じなければならない。

Article 194-14第百九十四条の十四

Transfer of Vehicle for Work at Height(高所作業車の移送)
Article 194-14, paragraph (1)

When using a loading plate, fills, etc., in the case where a vehicle for work at height is loaded to a truck, etc., or unloaded from a truck, etc., by self-propelling or towing for transferring the machine, the employer must comply with the following requirements in order to prevent dangers due to overturning, falling, etc., of the vehicle:

事業者は、高所作業車を移送するため自走又はけん引により貨物自動車に積卸しを行う場合において、道板、盛土等を使用するときは、当該高所作業車の転倒、転落等による危険を防止するため、次に定めるところによらなければならない。

Article 194-14, paragraph (1), item (i)

to load or unload the vehicle at a level and firm place;

積卸しは、平坦で堅固な場所において行うこと。

Article 194-14, paragraph (1), item (ii)

when using a loading plate, to use the plate with sufficient length, width and strength, and fix it securely with appropriate incline; and

道板を使用するときは、十分な長さ、幅及び強度を有する道板を用い、適当なこう配で確実に取り付けること。

Article 194-14, paragraph (1), item (iii)

when using fills or a temporary stand, etc., to secure sufficient width, strength and appropriate incline.

盛土、仮設台等を使用するときは、十分な幅及び強度並びに適当なこう配を確保すること。

Article 194-15第百九十四条の十五

Restriction of Riding(搭乗の制限)
Article 194-15, paragraph (1)

When the work using a vehicle for work at height is carried out, the employer must not have a person engaged in work at the workshop ride in any place other than the riding seat or the working floor.

事業者は、高所作業車を用いて作業を行うときは、当該作業場において作業に従事する作業従事者を乗車席及び作業床以外の箇所に乗せてはならない。

Article 194-16第百九十四条の十六

Restriction of Use(使用の制限)
Article 194-16, paragraph (1)

As regards a vehicle for work at height, the employer must not use it for the load exceeding the loading capacity (meaning the maximum load the vehicle is capable of raising with personnel or loads on working floor, in accordance with its structure and materials of the vehicle for work at height) and for other purposes exceeding its capabilities.

事業者は、高所作業車については、積載荷重(高所作業車の構造及び材料に応じて、作業床に人又は荷を乗せて上昇させることができる最大の荷重をいう。)その他の能力を超えて使用してはならない。

Article 194-17第百九十四条の十七

Restriction on the Use for Purposes Other than the Main Purpose(主たる用途以外の使用の制限)
Article 194-17, paragraph (1)

The employer must not use a vehicle for work at height for purposes other than its main purpose, such as hoisting loads; provided, however, that this does not apply when there is no risk of endangering workers in doing so.

事業者は、高所作業車を荷のつり上げ等当該高所作業車の主たる用途以外の用途に使用してはならない。ただし、労働者に危険を及ぼすおそれのないときは、この限りでない。

Article 194-18第百九十四条の十八

Repairs(修理等)
Article 194-18, paragraph (1)

When carrying out the work of repairing a vehicle for work at height, or fitting or removing the working floor, the employer must designate a person to supervise the work and have the person carry out the following matters:

事業者は、高所作業車の修理又は作業床の装着若しくは取り外しの作業を行うときは、当該作業を指揮する者を定め、その者に次の事項を行わせなければならない。

Article 194-18, paragraph (1), item (i)

to decide the work procedures, and directly supervise the work; and

作業手順を決定し、作業を直接指揮すること。

Article 194-18, paragraph (1), item (ii)

to monitor the use of the safety prop, safety block, etc., prescribed in paragraph (1) of the following Article.

次条第一項に規定する安全支柱、安全ブロック等の使用状況を監視すること。

Article 194-19第百九十四条の十九

Prevention of Danger Due to Falling Booms(ブーム等の降下による危険の防止)
Article 194-19, paragraph (1)

When carrying out the work of repairs, inspection, etc., below the raised boom of a vehicle for work at height, the employer must have the worker engaging in the work use a safety prop and a safety block, etc., in order to prevent workers from dangers due to the unexpected falling of the boom, etc.

事業者は、高所作業車のブーム等を上げ、その下で修理、点検等の作業を行うときは、ブーム等が不意に降下することによる労働者の危険を防止するため、当該作業に従事する労働者に安全支柱、安全ブロック等を使用させなければならない。

Article 194-19, paragraph (2)

The worker engaging in the work set forth in the preceding paragraph must use the safety prop and safety block, etc., set forth in the same paragraph.

前項の作業に従事する労働者は、同項の安全支柱、安全ブロック等を使用しなければならない。

Article 194-20第百九十四条の二十

Restriction of Riding on the Working Floor(作業床への搭乗制限等)
Article 194-20, paragraph (1)

When having a vehicle for work at height (excluding those with a structure of carrying out the traveling operation on the working floor; hereinafter the same applies in this Article) travel in a workshop where workers carry out work, the employer must not allow a person engaged in work to ride on the working floor of the vehicle for work at height; provided, however, that this does not apply when having the vehicle for work at height travel at a level and firm place, and the following measures have been taken:

事業者は、労働者が作業を行う作業場において、高所作業車(作業床において走行の操作をする構造のものを除く。以下この条において同じ。)を走行させるときは、当該高所作業車の作業床に作業従事者を乗せてはならない。ただし、平坦で堅固な場所において高所作業車を走行させる場合で、次の措置を講じたときは、この限りでない。

Article 194-20, paragraph (1), item (i)

to arrange a guide, and have the person guide the vehicle for work at height;

誘導者を配置し、その者に高所作業車を誘導させること。

Article 194-20, paragraph (1), item (ii)

to set fixed signals and have the guide set forth in the preceding item give the signals;

一定の合図を定め、前号の誘導者に当該合図を行わせること。

Article 194-20, paragraph (1), item (iii)

to set an appropriate working speed limit for the vehicle for work at height in accordance with the height of the working floor and the length of the boom, etc. of the vehicle for work at height in advance, and have the operator operate the vehicle within the speed limit.

あらかじめ、作業時における当該高所作業車の作業床の高さ及びブームの長さ等に応じた高所作業車の適正な制限速度を定め、それにより運転者に運転させること。

Article 194-20, paragraph (2)

A person engaged in work, excluding the case referred to in the proviso of the preceding paragraph, must not ride on the working floor of a vehicle for work at height while it is traveling.

作業従事者は、前項ただし書の場合を除き、走行中の高所作業車の作業床に乗つてはならない。

Article 194-20, paragraph (3)

The operator of the vehicle for work at height set forth in the proviso of paragraph (1) must follow the instructions given by the guide set forth in item (i) of the same paragraph and the signals set forth in item (ii) of the same paragraph, and must not operate the vehicle for work at height at a speed exceeding the speed limit set forth in item (iii) of the same paragraph.

第一項ただし書の高所作業車の運転者は、同項第一号の誘導者が行う誘導及び同項第二号の合図に従わなければならず、かつ、同項第三号の制限速度を超えて高所作業車を運転してはならない。

Article 194-21第百九十四条の二十一

Article 194-21, paragraph (1)

When traveling a vehicle for work at height with a structure of carrying out the traveling operation on a working floor at places other than level and firm places, the employer must take the following measures:

事業者は、作業床において走行の操作をする構造の高所作業車を平坦で堅固な場所以外の場所で走行させるときは、次の措置を講じなければならない。

Article 194-21, paragraph (1), item (i)

to take the measures listed in paragraph (1), items (i) and (ii) of the preceding Article; and

前条第一項第一号及び第二号に掲げる措置を講ずること。

Article 194-21, paragraph (1), item (ii)

to establish in advance, an appropriate working speed limit for the vehicle for work at height in accordance with the height of the working floor and the length of the boom of the vehicle for work at height, and the landform and condition of the ground pertaining to the work, and have the operator operate the vehicle within the speed limit.

あらかじめ、作業時における当該高所作業車の作業床の高さ及びブームの長さ、作業に係る場所の地形及び地盤の状態等に応じた高所作業車の適正な制限速度を定め、それにより運転者に運転させること。

Article 194-21, paragraph (2)

The provisions of paragraph (3) of the preceding Article apply mutatis mutandis to the operator of the vehicle for work at height set forth in the preceding paragraph. In this case, the term "item (iii) of the same paragraph" in paragraph (3) of the same Article is deemed to be replaced with "paragraph (1), item (ii) of the following Article."

前条第三項の規定は、前項の高所作業車の運転者について準用する。この場合において、同条第三項中「同項第三号」とあるのは、「次条第一項第二号」と読み替えるものとする。

Article 194-22第百九十四条の二十二

Use of Fall Arrest Equipment with the Required Performance, etc.(要求性能墜落制止用器具等の使用)
Article 194-22, paragraph (1)

When the work using a vehicle for work at height (excluding those with the structure in which the working floor rises or lowers only in the direction perpendicular to the ground plane) is carried out, the employer must have the workers on the working floor of the vehicle for work at height use fall arrest equipment with the required performance, etc.

事業者は、高所作業車(作業床が接地面に対し垂直にのみ上昇し、又は下降する構造のものを除く。)を用いて作業を行うときは、当該高所作業車の作業床上の労働者に要求性能墜落制止用器具等を使用させなければならない。

Article 194-22, paragraph (2)

The worker set forth in the preceding paragraph must use fall arrest equipment with the required performance, etc.

前項の労働者は、要求性能墜落制止用器具等を使用しなければならない。

Article 194-23第百九十四条の二十三

Periodical Self-inspection(定期自主検査)
Article 194-23, paragraph (1)

As regards a vehicle for work at height, the employer must carry out a self-inspection for the following matters periodically once every period not exceeding one year; provided, however, that this does not apply to the non-use period of a vehicle for work at height which is not used for a period exceeding one year:

事業者は、高所作業車については、一年以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一年を超える期間使用しない高所作業車の当該使用しない期間においては、この限りでない。

Article 194-23, paragraph (1), item (i)

abnormalities in the compression pressure, valve clearance and other abnormalities of the prime mover;

圧縮圧力、弁すき間その他原動機の異常の有無

Article 194-23, paragraph (1), item (ii)

abnormalities in the clutch, transmission, propeller shaft, differential and other abnormalities of power transmission devices;

クラッチ、トランスミッション、プロペラシャフト、デファレンシャルその他動力伝達装置の異常の有無

Article 194-23, paragraph (1), item (iii)

abnormalities in the drive wheel, idling wheel, vertical trunk roller, belt, tire, wheel bearing and other abnormalities of traveling devices;

起動輪、遊動輪、上下転輪、履帯、タイヤ、ホイールベアリングその他走行装置の異常の有無

Article 194-23, paragraph (1), item (iv)

abnormalities in the rotation angle of left and right steering wheels, knuckle, rod, arm and other abnormalities of controlling devices;

かじ取り車輪の左右の回転角度、ナックル、ロッド、アームその他操縦装置の異常の有無

Article 194-23, paragraph (1), item (v)

abnormalities in braking capability, brake drum, brake shoe and other abnormalities of braking devices;

制動能力、ブレーキドラム、ブレーキシューその他制動装置の異常の有無

Article 194-23, paragraph (1), item (vi)

abnormalities in the boom, lifting and lowering device, bending device, balance device, working floor and other abnormalities of working devices;

ブーム、昇降装置、屈折装置、平衡装置、作業床その他作業装置の異常の有無

Article 194-23, paragraph (1), item (vii)

abnormalities in the hydraulic pump, hydraulic motor, cylinder, safety valve and other abnormalities of the hydraulic system.

油圧ポンプ、油圧モーター、シリンダー、安全弁その他油圧装置の異常の有無

Article 194-23, paragraph (1), item (viii)

abnormalities in voltage, amperage and other abnormalities of the electrical system; and

電圧、電流その他電気系統の異常の有無

Article 194-23, paragraph (1), item (ix)

abnormalities in the body, operating device, safety device, locking device, warning device, direction indicator, lighting device and meter.

車体、操作装置、安全装置、ロック装置、警報装置、方向指示器、灯火装置及び計器の異常の有無

Article 194-23, paragraph (2)

As regards the vehicle for work at height set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.

事業者は、前項ただし書の高所作業車については、その使用を再び開始する際に、同項各号に掲げる事項について自主検査を行わなければならない。

Article 194-24第百九十四条の二十四

Article 194-24, paragraph (1)

As regards a vehicle for work at height, the employer must carry out a self-inspection for the following matters periodically once every period not exceeding one month; provided, however, that this does not apply to the non-use period of a vehicle for work at height which is not used for a period exceeding one month:

事業者は、高所作業車については、一月以内ごとに一回、定期に、次の事項について自主検査を行わなければならない。ただし、一月を超える期間使用しない高所作業車の当該使用しない期間においては、この限りでない。

Article 194-24, paragraph (1), item (i)

abnormalities in the braking device, clutch and steering system;

制動装置、クラッチ及び操作装置の異常の有無

Article 194-24, paragraph (1), item (ii)

abnormalities in the working device and hydraulic system; and

作業装置及び油圧装置の異常の有無

Article 194-24, paragraph (1), item (iii)

abnormalities in the safety device.

安全装置の異常の有無

Article 194-24, paragraph (2)

As regards the vehicle for work at height set forth in the proviso of the preceding paragraph, the employer must carry out a self-inspection for the matters listed in each item of the same paragraph before resuming the operation.

事業者は、前項ただし書の高所作業車については、その使用を再び開始する際に、同項各号に掲げる事項について自主検査を行わなければならない。

Article 194-25第百九十四条の二十五

Record of Periodical Self-inspections(定期自主検査の記録)
Article 194-25, paragraph (1)

When having carried out the self-inspection set forth in the preceding two Articles, the employer must record the following matters and preserve the record for three years:

事業者は、前二条の自主検査を行つたときは、次の事項を記録し、これを三年間保存しなければならない。

Article 194-25, paragraph (1), item (i)

the date of the inspection;

検査年月日

Article 194-25, paragraph (1), item (ii)

the method of the inspection;

検査方法

Article 194-25, paragraph (1), item (iii)

the parts inspected;

検査箇所

Article 194-25, paragraph (1), item (iv)

the results of the inspection;

検査の結果

Article 194-25, paragraph (1), item (v)

the name of the person who carried out the inspection; and

検査を実施した者の氏名

Article 194-25, paragraph (1), item (vi)

when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.

検査の結果に基づいて補修等の措置を講じたときは、その内容

Article 194-26第百九十四条の二十六

Specified Self-inspection(特定自主検査)
Article 194-26, paragraph (1)

The specified inspection pertaining to the vehicle for work at height is to be the self-inspection prescribed in Article 194-23.

高所作業車に係る特定自主検査は、第百九十四条の二十三に規定する自主検査とする。

Article 194-26, paragraph (2)

The provisions of Article 151-24, paragraph (2) apply mutatis mutandis to a person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in Article 45, paragraph (2) of the Act pertaining to a vehicle for work at height. In this case, the term "forklift" in Article 151-24, paragraph (2), item (i) is deemed to be replaced with "vehicle for work at height."

第百五十一条の二十四第二項の規定は、高所作業車に係る法第四十五条第二項の厚生労働省令で定める資格を有するものについて準用する。この場合において、第百五十一条の二十四第二項第一号中「フォークリフト」とあるのは、「高所作業車」と読み替えるものとする。

Article 194-26, paragraph (3)

As regards the vehicle for work at height (limited to those for which Article 48, paragraph (1) of the Road Transport Vehicle Act applies) used for traveling, when the employer has carried out an inspection pursuant to the provisions of the same paragraph, they are not required to carry out the self-inspection set forth in Article 194-23 for the parts where the inspection has been carried out.

事業者は、運行の用に供する高所作業車(道路運送車両法第四十八条第一項の適用を受けるものに限る。)について、同項の規定に基づいて点検を行つた場合には、当該点検を行つた部分については第百九十四条の二十三の自主検査を行うことを要しない。

Article 194-26, paragraph (4)

As regards the application of the provisions of the preceding Article when having a registered inspection agency conduct the specified inspection pertaining to a vehicle for work at height, the term "the name of the person who has carried out the inspection" in item (v) of the same Article is deemed to be replaced with "the name of the registered inspection agency."

高所作業車に係る特定自主検査を検査業者に実施させた場合における前条の規定の適用については、同条第五号中「検査を実施した者の氏名」とあるのは、「検査業者の名称」とする。

Article 194-26, paragraph (5)

When having carried out the specified inspection pertaining to a vehicle for work at height, the employer must affix an inspection sticker stating the month and year when the specified inspection was carried out at a readily visible part of the vehicle.

事業者は、高所作業車に係る自主検査を行つたときは、当該高所作業車の見やすい箇所に、特定自主検査を行つた年月を明らかにすることができる検査標章をはり付けなければならない。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy