Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 April 2027, in 4 months

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter I-3 Logging Machines, etc. (Articles 151-101 to 151-120)

The law as Ministerial Order Partially Amending the Ordinance on Industrial Safety and Health (Ministry of Health, Labour and Welfare Order No. 12 of 2025) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Article 151-101第百五十一条の百一

Restriction on Riding(搭乗の制限)
Article 151-101, paragraph (1)

When carrying out work using a vehicle type logging machine, the employer must not allow a person engaged in work at the workshop to ride on places other than the seat or the loading platform; provided, however, that this does not apply when measures for preventing dangers due to falling have been taken.

事業者は、車両系木材伐出機械を用いて作業を行うときは、当該作業場において作業に従事する作業従事者を乗車席又は荷台以外の箇所に乗せてはならない。ただし、墜落による危険を防止するための措置を講じたときは、この限りでない。

Article 151-102第百五十一条の百二

Restriction of Use(使用の制限)
Article 151-102, paragraph (1)

When carrying out work using a vehicle type logging machine, the employer must observe the stability, the maximum loading capacity, the maximum working load, etc., decided on the basis of the structure of the vehicle type logging machine, in order to prevent workers from dangers due to overturning or breaking into a run of the vehicle type logging machine or destruction of working devices such as a boom, an arm, etc.

事業者は、車両系木材伐出機械を用いて作業を行うときは、当該車両系木材伐出機械の転倒若しくは逸走又はブーム、アーム等の作業装置の破壊による労働者の危険を防止するため、当該車両系木材伐出機械についてその構造上定められた安定度、最大積載荷重、最大使用荷重等を守らなければならない。

Article 151-103第百五十一条の百三

Restriction on the Use for Other than Main Purpose(主たる用途以外の使用の制限)
Article 151-103, paragraph (1)

The employer must not use a vehicle type logging machine for a purpose other than its main purpose, such as lifting logs, etc. via a wire rope by a wood grapple.

事業者は、車両系木材伐出機械を、木材グラツプルによるワイヤロープを介した原木等のつり上げ等当該車両系木材伐出機械の主たる用途以外の用途に使用してはならない。

Article 151-103, paragraph (2)

The provisions of the preceding paragraph do not apply where there is no risk of endangering workers, such as where a hung tree is handled by pulling it down, using a winch and a guide block, in a direction other than toward the operator.

前項の規定は、ウインチ及びガイドブロツクを用いて運転者以外の方向にかかり木を引き倒すことによりかかり木を処理する場合等、労働者に危険を及ぼすおそれのない場合には、適用しない。

Article 151-104第百五十一条の百四

Repairs(修理等)
Article 151-104, paragraph (1)

When carrying out the work of repairing a vehicle type logging machine, or fitting or removing its attachments, the employer must designate a person to supervise the work and have the person carry out the following matters:

事業者は、車両系木材伐出機械の修理又はアタッチメントの装着若しくは取り外しの作業を行うときは、当該作業を指揮する者を定め、その者に次の事項を行わせなければならない。

Article 151-104, paragraph (1), item (i)

to decide the work procedures, and directly supervise the work; and

作業手順を決定し、作業を直接指揮すること。

Article 151-104, paragraph (1), item (ii)

to monitor the use by workers of safety props, safety blocks, etc., set forth in the proviso of Article 151-97, paragraph (1).

第百五十一条の九十七第一項ただし書に規定する安全支柱、安全ブロック等の労働者の使用状況を監視すること。

Article 151-105第百五十一条の百五

Restriction on Riding at the Operating Station for Operating the Working Device(作業装置の運転のための運転位置への搭乗の制限)
Article 151-105, paragraph (1)

When, at a workshop where workers carry out work, causing a vehicle type logging machine whose operating station for traveling differs from its operating station for operating the working device to travel, the employer must not have a person engaged in work ride at the operating station for operating the working device of the vehicle type logging machine.

事業者は、労働者が作業を行う作業場において、走行のための運転位置と作業装置の運転のための運転位置が異なる車両系木材伐出機械を走行させるときは、当該車両系木材伐出機械の作業装置の運転のための運転位置に作業従事者を乗せてはならない。

Article 151-105, paragraph (2)

In the case set forth in the preceding paragraph, a person engaged in work must not ride at the operating station for operating the working device of the vehicle type logging machine set forth in the same paragraph.

作業従事者は、前項の場合において同項の車両系木材伐出機械の作業装置の運転のための運転位置に乗つてはならない。

Article 151-106第百五十一条の百六

Prohibition of Work in Bad Weather(悪天候時の作業禁止)
Article 151-106, paragraph (1)

When carrying out work using a vehicle type logging machine, the employer must not have the work carried out when dangers are expected in carrying out the work due to bad weather such as strong wind, heavy rain or heavy snow.

事業者は、車両系木材伐出機械を用いる作業を行う場合において、強風、大雨、大雪等の悪天候のため、当該作業の実施について危険が予想されるときは、当該作業を行わせてはならない。

Article 151-107第百五十一条の百七

Wearing of Safety Helmet(保護帽の着用)
Article 151-107, paragraph (1)

When carrying out work using a vehicle type logging machine, the employer must have the workers engaging in the work wear a safety helmet in order to prevent workers from dangers due to objects that come flying or falling.

事業者は、車両系木材伐出機械を用いて作業を行うときは、物体の飛来又は落下による労働者の危険を防止するため、当該作業に従事する労働者に保護帽を着用させなければならない。

Article 151-107, paragraph (2)

The worker engaging in the work set forth in the preceding paragraph must wear the safety helmet set forth in the same paragraph.

前項の作業に従事する労働者は、同項の保護帽を着用しなければならない。

Article 151-108第百五十一条の百八

Inspection(検査)
Article 151-108, paragraph (1)

As regards a vehicle type logging machine, the employer must endeavor to carry out inspection of the following matters periodically once every period not exceeding one year; provided, however, that this does not apply to the non-use period of a vehicle type logging machine which is not used for a period exceeding one year:

事業者は、車両系木材伐出機械については、一年を超えない期間ごとに一回、定期に、次の事項について検査を行うよう努めなければならない。ただし、一年を超える期間使用しない車両系木材伐出機械の当該使用しない期間においては、この限りでない。

Article 151-108, paragraph (1), item (i)

abnormalities in the prime mover;

原動機の異常の有無

Article 151-108, paragraph (1), item (ii)

abnormalities in power transmission device and traveling device;

動力伝達装置及び走行装置の異常の有無

Article 151-108, paragraph (1), item (iii)

abnormalities in braking device and controlling device;

制動装置及び操縦装置の異常の有無

Article 151-108, paragraph (1), item (iv)

abnormalities in the working device and hydraulic system; and

作業装置及び油圧装置の異常の有無

Article 151-108, paragraph (1), item (v)

abnormalities in the body, head guard, protective equipment against flying objects, outriggers, electrical system, lighting device and meters.

車体、ヘツドガード、飛来物防護設備、アウトリガー、電気系統、灯火装置及び計器の異常の有無

Article 151-108, paragraph (2)

As regards a vehicle type logging machine set forth in the proviso of the preceding paragraph, the employer must endeavor to carry out inspection of the matters listed in each item of the same paragraph when starting its use again.

事業者は、前項ただし書の車両系木材伐出機械については、その使用を再び開始する際に、同項各号に掲げる事項について検査を行うよう努めなければならない。

Article 151-109第百五十一条の百九

Article 151-109, paragraph (1)

As regards a vehicle type logging machine, the employer must endeavor to carry out inspection of the following matters periodically once every period not exceeding one month; provided, however, that this does not apply to the non-use period of a vehicle type logging machine which is not used for a period exceeding one month:

事業者は、車両系木材伐出機械については、一月を超えない期間ごとに一回、定期に、次の事項について検査を行うよう努めなければならない。ただし、一月を超える期間使用しない車両系木材伐出機械の当該使用しない期間においては、この限りでない。

Article 151-109, paragraph (1), item (i)

abnormalities in braking device, clutch and controlling device;

制動装置、クラツチ及び操縦装置の異常の有無

Article 151-109, paragraph (1), item (ii)

abnormalities in the working device and hydraulic system; and

作業装置及び油圧装置の異常の有無

Article 151-109, paragraph (1), item (iii)

abnormalities in head guard and protective equipment against flying objects.

ヘツドガード及び飛来物防護設備の異常の有無

Article 151-109, paragraph (2)

As regards a vehicle type logging machine set forth in the proviso of the preceding paragraph, the employer must endeavor to carry out inspection of the matters listed in each item of the same paragraph when starting its use again.

事業者は、前項ただし書の車両系木材伐出機械については、その使用を再び開始する際に、同項各号に掲げる事項について検査を行うよう努めなければならない。

Article 151-110第百五十一条の百十

Inspection(点検)
Article 151-110, paragraph (1)

When carrying out work using a vehicle type logging machine, the employer must inspect the following matters before commencing the work for the day:

事業者は、車両系木材伐出機械を用いて作業を行うときは、その日の作業を開始する前に、次の事項について点検を行わなければならない。

Article 151-110, paragraph (1), item (i)

functions of the braking device and controlling device;

制動装置及び操縦装置の機能

Article 151-110, paragraph (1), item (ii)

functions of the working device and hydraulic system;

作業装置及び油圧装置の機能

Article 151-110, paragraph (1), item (iii)

abnormalities in the wire rope and crawler belts or wheels; and

ワイヤロープ及び履帯又は車輪の異常の有無

Article 151-110, paragraph (1), item (iv)

function of the front lamp.

前照灯の機能

Article 151-111第百五十一条の百十一

Repairs(補修等)
Article 151-111, paragraph (1)

When having found an abnormality in carrying out the inspection set forth in Article 151-108 or Article 151-109, or the inspection set forth in the preceding Article, the employer must immediately make repairs or take other necessary measures.

事業者は、第百五十一条の百八若しくは第百五十一条の百九の検査又は前条の点検を行つた場合において、異常を認めたときは、直ちに補修その他必要な措置を講じなければならない。

Subsection 2 Machine for Felling, etc.第二款 伐木等機械

Article 151-112第百五十一条の百十二

Prevention of Dangers in Tree Felling Work(伐木作業における危険の防止)
Article 151-112, paragraph (1)

When carrying out the work of tree logging using a machine for felling, etc., the employer must have the operator who is to fell standing trees remove, for each standing tree, shrubs, branches, vines, loose stones and other objects that may cause danger when felling or during other work.

事業者は、伐木等機械を用いて伐木の作業を行うときは、立木を伐倒しようとする運転者に、それぞれの立木について、かん木、枝条、つる、浮石等で、伐倒の際その他作業中に危険を生ずるおそれのあるものを取り除かせなければならない。

Article 151-112, paragraph (2)

The operator set forth in the preceding paragraph must remove, for each standing tree, shrubs, branches, vines, loose stones and other objects that may cause danger when felling or during other work.

前項の運転者は、それぞれの立木について、かん木、枝条、つる、浮石等で、伐倒の際その他作業中に危険を生ずるおそれのあるものを取り除かなければならない。

Article 151-113第百五十一条の百十三

Prevention of Dangers in Work of Bucking(造材作業における危険の防止)
Article 151-113, paragraph (1)

When carrying out the work of bucking using a machine for felling, etc., the employer must, in order to prevent danger from the logs, etc. being bucked falling or slipping, have the operator who is to carry out the work take measures such as carrying out the work on level ground.

事業者は、伐木等機械を用いて造材の作業を行うときは、造材を行う原木等が転落し、又は滑ることによる危険を防止するため、当該作業を行おうとする運転者に、平たんな地面で当該作業を行う等の措置を講じさせなければならない。

Article 151-113, paragraph (2)

The operator set forth in the preceding paragraph must take the measures set forth in the same paragraph.

前項の運転者は、同項の措置を講じなければならない。

Subsection 3 Traveling Yarding Machine第三款 走行集材機械

Article 151-114第百五十一条の百十四

Safety Coefficient of Wire Ropes(ワイヤロープの安全係数)
Article 151-114, paragraph (1)

The employer must make the safety coefficient of a wire rope used for the winch or slings of a traveling yarding machine 4 or more.

事業者は、走行集材機械のウインチ又はスリングに用いるワイヤロープの安全係数については、四以上としなければならない。

Article 151-114, paragraph (2)

The safety coefficient set forth in the preceding paragraph is to be the value obtained by dividing the breaking load of a wire rope by the value of the maximum load applied to the wire rope.

前項の安全係数は、ワイヤロープの切断荷重の値を、当該ワイヤロープにかかる荷重の最大の値で除した値とする。

Article 151-115第百五十一条の百十五

Prohibition of the Use of an Inadequate Wire Rope(不適格なワイヤロープの使用禁止)
Article 151-115, paragraph (1)

With regard to a wire rope used for the winch or slings of a traveling yarding machine or a wire rope used for securing loads, the employer must not use one that falls under any of the following items:

事業者は、走行集材機械のウインチ若しくはスリングに用いるワイヤロープ又は積荷の固定に用いるワイヤロープについては、次のいずれかに該当するものを使用してはならない。

Article 151-115, paragraph (1), item (i)

a wire rope in which 10 percent or more of the wires (excluding filler wires; the same applies hereinafter in this item) have broken within one lay;

ワイヤロープ一よりの間において素線(フイラ線を除く。以下本号において同じ。)数の十パーセント以上の素線が切断したもの

Article 151-115, paragraph (1), item (ii)

those with the reduction ratio of a diameter due to wear-out that exceeds 7% of the nominal diameter;

摩耗による直径の減少が公称径の七パーセントを超えるもの

Article 151-115, paragraph (1), item (iii)

those with kinks; and

キンクしたもの

Article 151-115, paragraph (1), item (iv)

those with marked deformation or corrosion.

著しい形崩れ又は腐食のあるもの

Article 151-116第百五十一条の百十六

Inspection of Slings, etc.(スリング等の点検)
Article 151-116, paragraph (1)

When carrying out work using a traveling yarding machine, the employer must, before starting the work of the day, inspect the condition of the slings used for the work and the wire ropes used for securing loads, and if an abnormality is found, must immediately repair or replace them.

事業者は、走行集材機械を用いて作業を行うときは、その日の作業を開始する前に、当該作業に用いるスリング及び積荷の固定に用いるワイヤロープの状態について点検し、異常を認めたときは、直ちに、補修し、又は取り替えなければならない。

Article 151-117第百五十一条の百十七

Signals(合図)
Article 151-117, paragraph (1)

With regard to the operation of the winch of a traveling yarding machine, the employer must determine fixed signals and the person who gives the signals, and have those signals used in the operation.

事業者は、走行集材機械のウインチの運転について、一定の合図及び合図を行う者を定め、運転に当たつては、当該合図を使用させなければならない。

Article 151-117, paragraph (2)

The operator of the winch of the traveling yarding machine set forth in the preceding paragraph must follow the signals set forth in the same paragraph.

前項の走行集材機械のウインチの運転者は、同項の合図に従わなければならない。

Article 151-118第百五十一条の百十八

Loading of Logs, etc.(原木等の積載)
Article 151-118, paragraph (1)

When loading logs, etc. onto a traveling yarding machine, the employer must comply with the following:

事業者は、走行集材機械に原木等を積載するときは、次に定めるところによらなければならない。

Article 151-118, paragraph (1), item (i)

to load them in a manner that prevents uneven loading; and

偏荷重が生じないように積載すること。

Article 151-118, paragraph (1), item (ii)

to take necessary measures such as securing the load with a wire rope, in order to prevent workers from dangers due to collapsing of the load or falling of the logs, etc.

荷崩れ又は原木等の落下による労働者の危険を防止するため、積荷をワイヤロープで固定する等必要な措置を講ずること。

Article 151-119第百五十一条の百十九

Restriction of Riding on a Loading Platform(荷台への乗車制限)
Article 151-119, paragraph (1)

When causing a traveling yarding machine having a loading platform to travel at a workshop where workers carry out work, the employer must not allow a person engaged in work to ride on the loading platform of that traveling yarding machine.

事業者は、労働者が作業を行う作業場において、荷台を有する走行集材機械を走行させるときは、当該走行集材機械の荷台に作業従事者を乗車させてはならない。

Article 151-119, paragraph (2)

In the case referred to in the preceding paragraph, a person engaged in work must not ride on the loading platform set forth in the same paragraph.

作業従事者は、前項の場合において同項の荷台に乗車してはならない。

Subsection 4 Cable Yarding Machine第四款 架線集材機械

Article 151-120第百五十一条の百二十

Safety Coefficient of Wire Ropes(ワイヤロープの安全係数)
Article 151-120, paragraph (1)

The employer must make the safety coefficient of a wire rope used for the winch or slings of a cable yarding machine 4 or more.

事業者は、架線集材機械のウインチ又はスリングに用いるワイヤロープの安全係数については、四以上としなければならない。

Article 151-120, paragraph (2)

The safety coefficient set forth in the preceding paragraph is to be the value obtained by dividing the breaking load of a wire rope by the value of the maximum load applied to the wire rope.

前項の安全係数は、ワイヤロープの切断荷重の値を、当該ワイヤロープにかかる荷重の最大の値で除した値とする。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy