Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 April 2027, in 4 months

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter IV Prevention of Explosions and Fires (Articles 321 to 328-5)

The law as Ministerial Order Partially Amending the Ordinance on Industrial Safety and Health, etc. (Ministry of Health, Labour and Welfare Order No. 89 of 2026) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Article 321第三百二十一条

Evacuation(避難)
Article 321, paragraph (1)

When carrying out blasting work, if persons engaged in work cannot evacuate to a safe distance, the employer must provide an evacuation shelter with a solidly protected front and top part.

事業者は、発破の作業を行う場合において、作業従事者が安全な距離に避難し得ないときは、前面と上部を堅固に防護した避難所を設けなければならない。

Section 7-2 Concrete Breaking Work第七節の二 コンクリート破砕器作業

Article 321-2第三百二十一条の二

Standards for Concrete Breaking Work(コンクリート破砕器作業の基準)
Article 321-2, paragraph (1)

When carrying out the breaking work using a concrete breaker, the employer must comply with the requirements set forth in the following items:

事業者は、コンクリート破砕器を用いて破砕の作業を行うときは、次に定めるところによらなければならない。

Article 321-2, paragraph (1), item (i)

when charging a concrete breaker, to prohibit the use of naked fire or smoking in the vicinity by indicating the prohibition in a conspicuous place or by other methods;

コンクリート破砕器を装塡するときは、その付近での裸火の使用又は喫煙について、禁止する旨を見やすい箇所に表示することその他の方法により禁止すること。

Article 321-2, paragraph (1), item (ii)

to use a safe charging tool, which is unlikely to cause ignition of the concrete breaker due to friction, shock, static electricity, etc.

装塡具は、摩擦、衝撃、静電気等によりコンクリート破砕器が発火するおそれのない安全なものを使用すること。

Article 321-2, paragraph (1), item (iii)

to use a safe stemming, which is unlikely to cause ignition or inflammation, such as cement mortar or sand;

込物は、セメントモルタル、砂その他の発火又は引火の危険のないものを使用すること。

Article 321-2, paragraph (1), item (iv)

to take measures to prevent the broken materials, etc., from scattering; and

破砕された物等の飛散を防止するための措置を講ずること。

Article 321-2, paragraph (1), item (v)

when the charged concrete breaker does not ignite after ignition, or when it is difficult to confirm that the charged concrete breaker has ignited, to remove the lead wire of the blaster from the igniter and short-circuit the end of the wire, and to take measures to prevent re-ignition; and not to allow the worker engaging in the concrete breaking work to approach the place where the concrete breaker is charged within five minutes after the measures have been taken.

点火後、装塡されたコンクリート破砕器が発火しないとき、又は装塡されたコンクリート破砕器が発火したことの確認が困難であるときは、コンクリート破砕器の母線を点火器から取り外し、その端を短絡させておき、かつ、再点火できないように措置を講じ、その後五分以上経過した後でなければ、当該作業に従事する労働者をコンクリート破砕器の装塡箇所に接近させないこと。

Article 321-3第三百二十一条の三

Appointment of an Operations Supervisor of Concrete Breaking(コンクリート破砕器作業主任者の選任)
Article 321-3, paragraph (1)

As regards the work set forth in Article 6, item (viii)-2 of the Order, the employer must appoint an operations supervisor of concrete breaking from the persons who have completed the skill training course for operations supervisor of concrete breaking.

事業者は、令第六条第八号の二の作業については、コンクリート破砕器作業主任者技能講習を修了した者のうちから、コンクリート破砕器作業主任者を選任しなければならない。

Article 321-4第三百二十一条の四

Duties of the Operations Supervisor of Concrete Breaking(コンクリート破砕器作業主任者の職務)
Article 321-4, paragraph (1)

The employer must have the operations supervisor of concrete breaking carry out the following matters:

事業者は、コンクリート破砕器作業主任者に次の事項を行わせなければならない。

Article 321-4, paragraph (1), item (i)

to decide the work method and directly supervise the work;

作業の方法を決定し、作業を直接指揮すること。

Article 321-4, paragraph (1), item (ii)

to indicate the place for evacuation and the route to that place to the workers engaging in the work;

作業に従事する労働者に対し、退避の場所及び経路を指示すること。

Article 321-4, paragraph (1), item (iii)

to confirm that workers have been evacuated from the dangerous area before ignition;

点火前に危険区域内から労働者が退避したことを確認すること。

Article 321-4, paragraph (1), item (iv)

to appoint a worker in charge of ignition;

点火者を定めること。

Article 321-4, paragraph (1), item (v)

to give a signal of ignition; and

点火の合図をすること。

Article 321-4, paragraph (1), item (vi)

to check for misfires or residual gunpowder.

不発の装薬又は残薬の有無について点検すること。

Section 8 Miscellaneous Provisions第八節 雑則

Article 322第三百二十二条

Underground Workshop(地下作業場等)
Article 322, paragraph (1)

When carrying out the work at underground workshop where flammable gas is likely to be generated (excluding the case of carrying out construction works of tunnels etc., prescribed in Article 382), or when carrying out an open-cut excavation work at places where discharged gas from gas supply lines is likely to be discharged (meaning the excavation work of natural ground or transportation, etc., of earth and rocks associated with the excavation (limited to the work which is carried out at places where excavating work of natural ground are carried out and in the vicinity of the places); the same applies hereinafter), the employer must take the following measures in order to prevent explosion or fire:

事業者は、可燃性ガスが発生するおそれのある地下作業場において作業を行うとき(第三百八十二条に規定するずい道等の建設の作業を行うときを除く。)、又はガス導管からガスが発散するおそれのある場所において明り掘削の作業(地山の掘削又はこれに伴う土石の運搬等の作業(地山の掘削の作業が行われる箇所及びこれに近接する箇所において行われるものに限る。)をいう。以下同じ。)を行うときは、爆発又は火災を防止するため、次に定める措置を講じなければならない。

Article 322, paragraph (1), item (i)

to appoint a person in charge of measuring the concentration of the gas, and have the person measure the concentration of the gas every day before commencing the work and when having found an abnormality related to the gas at places where gas is likely to be generated or become stagnant;

これらのガスの濃度を測定する者を指名し、その者に、毎日作業を開始する前及び当該ガスに関し異常を認めたときに、当該ガスが発生し、又は停滞するおそれがある場所について、当該ガスの濃度を測定させること。

Article 322, paragraph (1), item (ii)

when it is found that the concentration of these gases has reached 30% or more of the value of the explosion lower limit, to immediately evacuate persons engaged in work to a safe place, suspend the use of fire or other things that are likely to become an ignition source, and conduct airing, ventilation, etc.

これらのガスの濃度が爆発下限界の値の三十パーセント以上であることを認めたときは、直ちに、作業従事者を安全な場所に退避させ、及び火気その他点火源となるおそれがあるものの使用を停止し、かつ、通風、換気等を行うこと。

Articles 323 to 324第三百二十三条から第三百二十四条まで

Articles 323 to 324, paragraph (1)

No English for this provision yet.

削除

Article 325第三百二十五条

Place Where Strong Light Is Emitted(強烈な光線を発散する場所)
Article 325, paragraph (1)

The employer must enclose places where it is likely to cause dangers due to strong light such as welding arc is emitted; provided, however, that this does not apply when it is inevitable due to the nature of the operation.

事業者は、アーク溶接のアークその他強烈な光線を発散して危険のおそれのある場所については、これを区画しなければならない。ただし、作業上やむを得ないときは、この限りでない。

Article 325, paragraph (2)

As regards places set forth in the preceding paragraph, the employer must provide appropriate personal protective equipment.

事業者は、前項の場所については、適当な保護具を備えなければならない。

Article 326第三百二十六条

Pressurized Feeding Facilities of Corrosive Liquid(腐食性液体の圧送設備)
Article 326, paragraph (1)

When carrying out the work of pressure feeding with power and through hoses those liquids which causes dangers of corrosive effect on the skin, such as sulfuric acid, nitric acid, hydrochloric acid, acetic acid, chlorosulfonic acid, caustic soda solution and cresol (hereinafter referred to as "corrosive liquids"), the employer must take the following measures for the equipment used in the work:

事業者は、硫酸、硝酸、塩酸、酢酸、クロールスルホン酸、か性ソーダ溶液、クレゾール等皮膚に対して腐食の危険を生ずる液体(以下「腐食性液体」という。)をホースをとおして、動力を用いて圧送する作業を行うときは、当該圧送に用いる設備について、次の措置を講じなければならない。

Article 326, paragraph (1), item (i)

to provide a pressure gauge at a readily visible location for the person who operates the equipment used for pressure feeding (hereinafter referred to as the "operator" in this Article), and a device for cutting off power at a place where the operator can easily operate it, respectively;

圧送に用いる設備の運転を行う者(以下この条において「運転者」という。)が見やすい位置に圧力計を、運転者が容易に操作することができる位置に動力を遮断するための装置を、それぞれ備え付けること。

Article 326, paragraph (1), item (ii)

to use the hoses and their connecting tools that are anti-corrosive, heat-resistant and cold-resistant against the corrosive liquids fed;

ホース及びその接続用具は、圧送する腐食性液体に対し、耐食性、耐熱性及び耐寒性を有するものを用いること。

Article 326, paragraph (1), item (iii)

for hoses, to set the pressure for their safe use by conducting hydraulic tests, etc., and indicate the set pressure on hoses, and not to carry out the feed using a pressure exceeding the pressure;

ホースについては、水圧試験等により、安全に使用することができる圧力を定め、これを当該ホースに表示し、かつ、当該圧力を超えて圧送を行わないこと。

Article 326, paragraph (1), item (iv)

when there is a risk of abnormal pressure acting on the inside of hoses, to provide the equipment used for pressure feeding with preventive device for excessive pressurizing such as unloaders and return valves;

ホースの内部に異常な圧力が加わるおそれのあるときは、圧送に用いる設備にアンローダ、リターンバルブ等の過圧防止装置を備え付けること。

Article 326, paragraph (1), item (v)

to securely connect the connecting parts of hoses and pipes other than hoses, and between hoses using connecting tools;

ホースとホース以外の管及びホース相互の接続箇所については、接続用具を用いて確実に接続すること。

Article 326, paragraph (1), item (vi)

when carrying out pressure feeding at a gauge pressure exceeding 200 kPa, as regards the connecting tool set forth in the preceding item, to use those whose structure is unlikely to be disconnected due to the pressure such as the screw connection method, three-hook connection method, etc., those having three or more bottoms at the part to mount hoses, etc.;

ゲージ圧力二百キロパスカルを超える圧力で圧送を行うときは、前号の接続用具については、ねじ込結合方式、三鈎式結合方式等の方式による接続用具で、ホースを装着する部分に三箇以上の谷を有するもの等当該圧力により離脱するおそれのない構造のものを用いること。

Article 326, paragraph (1), item (vii)

to appoint an operator and have the operator monitor the operation of the equipment used for pressure feeding and the pressure gauge; and

運転者を指名し、その者に圧送に用いる設備の運転及び圧力計の監視を行わせること。

Article 326, paragraph (1), item (viii)

to inspect the hoses and their connecting tools before commencing the use for the day, and to exchange them when there is a risk of scattering or leakage of corrosive liquids due to defects such as damage, corrosion, etc.

ホース及びその接続用具は、その日の使用を開始する前に点検し、損傷、腐食等の欠陥により、圧送する腐食性液体が飛散し、又は漏えいするおそれのあるときは、取り換えること。

Article 327第三百二十七条

Personal Protective Equipment(保護具)
Article 327, paragraph (1)

The employer must have the worker engaging in pressure feeding work of corrosive liquids wear personal protective equipment necessary to prevent the body from the danger of corrosion due to scattered, leaked or overflowing corrosive liquid.

事業者は、腐食性液体を圧送する作業に従事する労働者に、腐食性液体の飛散、漏えい又は溢流による身体の腐食の危険を防止するため必要な保護具を着用させなければならない。

Article 327, paragraph (2)

When having a contractor carry out part of the work set forth in the preceding paragraph, the employer must make it known to that contractor that it is necessary to wear the personal protective equipment necessary to prevent the danger of corrosion of the body due to scattering, leakage or overflow of corrosive liquids.

事業者は、前項の作業の一部を請負人に請け負わせるときは、当該請負人に対し、腐食性液体の飛散、漏えい又は溢流による身体の腐食の危険を防止するため必要な保護具を着用する必要がある旨を周知させなければならない。

Article 327, paragraph (3)

The worker engaging in the work set forth in paragraph (1), when having been instructed to wear the personal protective equipment set forth in the same paragraph, must wear the equipment.

第一項の作業に従事する労働者は、同項の保護具の着用を命じられたときは、これを着用しなければならない。

Article 328第三百二十八条

Restriction on the Use of Gas Other Than Air(空気以外のガスの使用制限)
Article 328, paragraph (1)

When carrying out the pressure feeding work of corrosive liquid using the pressure of compressed gas as power source, the employer must not use gas other than air for the compressed gas; provided, however, that in having completed the work, and immediately removing the gas, or when taking measures which are unlikely to cause danger of suffocation due to workers entering the facilities used for the pressure feeding, such as indicating that the gas exists, nitrogen or carbon dioxide gas may be used.

事業者は、圧縮したガスの圧力を動力として用いて腐食性液体を圧送する作業を行なうときは、空気以外のガスを当該圧縮したガスとして使用してはならない。ただし、当該作業を終了した場合において、直ちに当該ガスを排除するとき、又は当該ガスが存在することを表示する等労働者が圧送に用いた設備の内部に立ち入ることによる窒息の危険が生ずるおそれのない措置を講ずるときは、窒素又は炭酸ガスを使用することができる。

Article 328-2第三百二十八条の二

Work Standards for Filling Tires with Air(タイヤの空気充てん作業の基準)
Article 328-2, paragraph (1)

When assembling a tire for an automobile (excluding two-wheeled vehicles) (hereinafter referred to as "tires" in this Article) and filling a tire with air using an air compressor, the employer must have the worker engaging in the work adjust air pressure appropriately in accordance with the type of tire in order to prevent danger due to a burst tire, etc., and use appliances such as safety enclosures etc., in order to prevent pieces of burst tires, etc., from coming flying.

事業者は、自動車(二輪自動車を除く。)用タイヤ(以下この条において「タイヤ」という。)の組立てを行う場合において、空気圧縮機を用いてタイヤに空気を充てんする作業を行うときは、タイヤの破裂等による危険を防止するため、当該作業に従事する労働者に、タイヤの種類に応じて空気の圧力を適正に調節させ、及び安全囲い等破裂したタイヤ等の飛来を防止するための器具を使用させなければならない。

Article 328-2, paragraph (2)

The worker engaging in the work set forth the preceding paragraph must adjust air pressure appropriately corresponding to the type of tire and use the appliances set forth in the same paragraph.

前項の作業に従事する労働者は、タイヤの種類に応じて空気の圧力を適正に調節し、及び同項の器具を使用しなければならない。

Article 328-3第三百二十八条の三

Ship Modifications(船舶の改造等)
Article 328-3, paragraph (1)

In carrying out ship modifications, repairs and cleaning, etc., when carrying out the work using machinery or other such equipment that generates sparks or arcs or reaches high temperatures, that has a risk of becoming a source of ignition, or work using fire in areas inside the ship such as the hold or adjoining areas, the employers must measure the concentration of vapor of inflammable substances and flammable gas in the workplace and surrounding areas before commencing the work and as needed during work.

事業者は、船舶の改造、修理、清掃等を行う場合に、船倉等当該船舶の内部又はこれに接する場所において、火花若しくはアークを発し、若しくは高温となつて点火源となるおそれのある機械等又は火気を使用する作業を行うときは、当該作業を開始するとき及び当該作業中随時、作業箇所及びその周辺における引火性の物の蒸気又は可燃性ガスの濃度を測定しなければならない。

Article 328-4第三百二十八条の四

Modification of Manufacturing Facilities of Liquid Oxygen(液化酸素の製造設備の改造等)
Article 328-4, paragraph (1)

In carrying out modification, repairing and cleaning, etc., of the manufacturing facilities of liquid oxygen, when carrying out the work inside the facilities, the employer must comply with the following requirements:

事業者は、液化酸素を製造する設備の改造、修理、清掃等を行う場合において、当該設備の内部で作業を行うときは、次に定めるところによらなければならない。

Article 328-4, paragraph (1), item (i)

to decide the method and procedures of the work, and make them known to the workers concerned in advance;

当該作業の方法及び順序を決定し、あらかじめ、これを関係労働者に周知させること。

Article 328-4, paragraph (1), item (ii)

to designate a supervisor for the work and have the supervisor direct the work;

当該作業の指揮者を定め、その者に当該作業を指揮させること。

Article 328-4, paragraph (1), item (iii)

to doubly close valves or cocks or apply baffles in addition to closing valves or cocks in order to prevent the workplace from leakage of oxygen; and

作業箇所に酸素が漏えいしないように、バルブ若しくはコックを二重に閉止し、又はバルブ若しくはコックを閉止するとともに閉止板等を施すこと。

Article 328-4, paragraph (1), item (iv)

to lock the valves, cocks and baffles set forth in the preceding item, display a notice stating that they must not be opened, or place a watcher.

前号のバルブ、コック又は閉止板等に施錠し、これらを開放してはならない旨を表示し、又は監視人を置くこと。

Article 328-5第三百二十八条の五

Manufacturing of Hydroxylamine(ヒドロキシルアミン等の製造等)
Article 328-5, paragraph (1)

When manufacturing or handling hydroxylamine and its salt (hereinafter referred to as "hydroxylamine etc." in this Article), the employer must comply with the requirements of the following items in order to prevent explosion:

事業者は、ヒドロキシルアミン及びその塩(以下この条において「ヒドロキシルアミン等」という。)を製造し、又は取り扱うときは、爆発を防止するため、次に定めるところによらなければならない。

Article 328-5, paragraph (1), item (i)

to take measures to prevent the abnormal reaction between hydroxylamine, etc., and ferrous ion, etc., such as prevention of interfusion of ferrous ion etc., to hydroxylamine etc.; and

ヒドロキシルアミン等への鉄イオン等の混入を防止すること等のヒドロキシルアミン等と鉄イオン等との異常反応を防止するための措置を講ずること。

Article 328-5, paragraph (1), item (ii)

when carrying out the work of heating hydroxylamine, etc., to adjust the temperature.

ヒドロキシルアミン等の加熱の作業を行うときは、その温度を調整すること。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy