In a workshop where workers carry out work, the employer must provide a cover, an enclosure, a sleeve, an overbridge, etc. for the parts of a machine, such as a prime mover, a rotating shaft, a gear, a pulley and a belt, that are likely to endanger workers.
The employer must use the sunken head type or provide a cover for set-screws and other fixtures attached to a rotating shaft, a gear, a pulley, a flywheel, etc.
第三項
事業者は、ベルトの継目には、突出した止め具を使用してはならない。
The employer must not use a protruded fastener for joining a belt.
第四項
事業者は、第一項の踏切橋には、高さが九十センチメートル以上の手すりを設けなければならない。
The employer must provide a handrail with the height of 90 cm or more for the overbridge set forth in paragraph (1).
The employer must provide an enclosure under the belt for a belt that is located above a passage or a workplace and having a distance between pulleys of 3 m or more, width of 15 cm or more and speed of 10 m/sec or more.
The employer must provide a power cutting device such as a switch, a clutch or a belt shifter for each machine; provided, however, that this does not apply to a series of machines having a common power cutting device and not requiring manual supply or extraction of raw materials during the process of operation.
The employer must, when the machine set forth in the preceding paragraph is for the process of cutting, drawing, compressing, punching, bending or expressing, provide the power cutting device set forth in the same paragraph at a place where a person engaging in the processing work is able to operate it without leaving the work station.
The employer, as regards the power cutting device set forth in paragraph (1), must provide a device that can be easily operated and is not likely to unexpectedly activate due to contact, vibration, etc.
In starting the operation of a machine, when there is a risk of endangering workers, the employer must set fixed signals, designate a person who gives the signals, and have the person give the signals to the workers.
第二項
労働者は、前項の合図に従わなければならない。
A worker must follow the signals set forth in the preceding paragraph.
第百五条
(加工物等の飛来による危険の防止)Prevention of Dangers Due to Workpieces that Come Flying
When there is a risk of endangering workers due to workpieces, etc. that are cut or broken and come flying, the employer must provide a cover or an enclosure for the machine that scatters the workpieces, etc.; provided, however, that this does not apply where providing a cover or an enclosure is difficult due to the nature of the work and the employer has had workers use personal protective equipment.
A worker, when having been ordered to use personal protective equipment in the case referred to in the proviso of the preceding paragraph, must use the equipment.
第百六条
(切削屑の飛来等による危険の防止)Prevention of Dangers Due to Chips that Come Flying
When there is a risk of endangering workers due to cutting chips coming flying, etc., the employer must provide a cover or an enclosure for the machine that generates the cutting chips; provided, however, that this does not apply where providing a cover or an enclosure is difficult due to the nature of the work and the employer has had workers use personal protective equipment.
A worker, when having been ordered to use personal protective equipment in the case referred to in the proviso of the preceding paragraph, must use the equipment.
第百七条
(掃除等の場合の運転停止等)Suspension of Operation, etc. in the Case of Cleaning, etc.
When work of cleaning, lubrication, inspection, repair or adjustment of a machine (excluding blade parts) is carried out and there is a risk of endangering workers, the employer must suspend the operation of the machine; provided, however, that this does not apply if the work has to be carried out during operation of the machine and measures such as providing a cover on dangerous parts have been taken.
When the employer has suspended the operation of the machine pursuant to the provisions of the preceding paragraph, the employer must take measures such as locking the starting device of the machine and attaching a sign plate to the starting device, to prevent persons other than the workers engaging in the work set forth in the same paragraph from operating the machine.
第百八条
(刃部の掃除等の場合の運転停止等)Suspension of Operation, etc. in the Case of Cleaning, etc. of Blade Parts
When carrying out the work of cleaning, inspecting, repairing, replacing or adjusting the blade parts of a machine, the employer must suspend the operation of the machine; provided, however, that this does not apply if there is no risk of endangering workers due to the structure of the machine.
When the employer has suspended the operation of the machine pursuant to the provisions of the preceding paragraph, the employer must take the measures of locking the starting device of the machine and attaching a plate to prevent persons other than the workers engaging in the work set forth in the same paragraph from operating the machine.
When removing chips or using cutting lubricants for the blade part of a machine during operation, the employer must have a worker use a brush or other appropriate tools.
第四項
労働者は、前項の用具の使用を命じられたときは、これを使用しなければならない。
A worker, when having been ordered to use a tool set forth in the preceding paragraph, must use the tool.
When the stroke ends of the ram of a shaper, a table of a grinding machine or a planer, etc. have a risk of endangering workers, the employer must take measures such as providing a cover, an enclosure or a railing to prevent that danger.
第百九条
(巻取りロール等の危険の防止)Prevention of Dangers Due to Wind-Up Roll
The employer must provide a cover or an enclosure, etc., for a wind-up roll or a coil of a paper, a cloth or a wire rope, etc., which has a risk of endangering the workers.
When there is a risk of getting hair or clothing of a worker working caught in a power-driven machine, the employer must have the worker wear appropriate work cap or work clothes.
第二項
労働者は、前項の作業帽又は作業服の着用を命じられたときは、これらを着用しなければならない。
A worker, when having been ordered to wear work cap or work clothes set forth in the preceding paragraph, must wear them.
When there is a risk of getting fingers of the worker working caught in rotating blades of a drilling machine or a chamfering machine, the employer must not have the worker wear gloves.
第二項
労働者は、前項の場合において、手袋の使用を禁止されたときは、これを使用してはならない。
In the case referred to in the preceding paragraph, when a worker has been prohibited to wear gloves, the worker must not wear them.
第二節 工作機械
第百十二条
第一項
削除
この部分の英訳はまだありません。
第百十三条
(突出した加工物の覆い等)Cover on Workpieces Protruding from Machine Tools
When a rotating workpiece protruding from a vertical lathe, a turret lathe, etc., has a risk of endangering workers, the employer must provide a cover, an enclosure, etc.
The employer must provide a cover or enclosure on the teeth of band saws (excluding woodworking band saws) other than the parts necessary for sawing and the band wheel.
第百十五条
(丸のこ盤の歯の接触予防装置)Preventive Device for Contact with Teeth of a Circular Saw
第一項
事業者は、丸のこ盤(木材加工用丸のこ盤を除く。)には、歯の接触予防装置を設けなければならない。
The employer must provide a preventive device for contact with teeth of circular saws, etc. (excluding woodworking circular saws).
第百十六条
(立旋盤等のテーブルへの搭乗の禁止)Prohibition of Riding on a Table of a Vertical Lathe, etc.
In a workshop where a vertical lathe, a planer, etc. is used, the employer must not allow a person engaged in work in the workshop to ride on a table of a vertical lathe, a planer, etc. during operation; provided, however, that this does not apply when a person on the table or a person placed at the operation panel is able to immediately stop the machine.
A person engaged in work in the workshop set forth in the preceding paragraph, excluding the case referred to in the proviso of the same paragraph, may not ride on a table of a vertical lathe, a planer, etc., during operation.
When a rotating grinding wheel has a risk of endangering workers, the employer must provide a cover; provided, however, that this does not apply to a grinding wheel with a diameter of less than 50 mm.
As regards a grinding wheel, the employer must make a test run for one minute or longer before commencing the work for the day and for three minutes or longer when the grinding wheel has been replaced.
第百十九条
(研削といしの最高使用周速度をこえる使用の禁止)Prohibition of Operation of a Grinding Wheel at a Speed Exceeding the Maximum Allowable Speed
第一項
事業者は、研削といしについては、その最高使用周速度をこえて使用してはならない。
As regards a grinding wheel, the employer must not operate the grinding wheel at a speed exceeding the maximum allowable speed.
第百二十条
(研削といしの側面使用の禁止)Prohibition of Use of Side Surfaces of a Grinding Wheel
第一項
事業者は、側面を使用することを目的とする研削といし以外の研削といしの側面を使用してはならない。
The employer must not use the side surfaces of a grinding wheel except for a grinding wheel designed to use the side surfaces.
The employer must provide a cover on a buffing machine (excluding the buffing machine that use a cloth buff or a cork buff) other than the parts necessary for polishing.
第三節 木材加工用機械
第百二十二条
(丸のこ盤の反ぱつ予防装置)Anti-Kickback Device for a Circular Saw
The employer must provide a spreader or other anti-kickback device, etc., for a woodworking circular saw (excluding a cross cut circular saw and other circular saws that do not have the risk of endangering workers due to kickback of the wood).
第百二十三条
(丸のこ盤の歯の接触予防装置)Preventive Device for Contact with Teeth of a Circular Saw
The employer must provide a preventive device for contact with teeth of a woodworking circular saw (excluding a circular saw for lumber and that with an automatic feeding device).
第百二十四条
(帯のこ盤の歯及びのこ車の覆い等)Cover on Teeth or Band Wheel of a Band Saw