Chapter IV Prevention of Explosions and Fires (Articles 302 to 313)
The law as Ministerial Order Partially Amending the Safety Ordinance for Cranes and the Ordinance on Industrial Safety and Health (Ministry of Health, Labour and Welfare Order No. 90 of 2026) leaves it, with the words it changes marked.
The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.
Article 302第三百二条
Generator Room(発生器室)
Article 302, paragraph (1)
As regards an acetylene generator of acetylene welding equipment (hereinafter referred to as "generator"), the employer must install the generator in a dedicated generator room (hereinafter referred to as "generator room").
As regards a generator room, the employer must install it in the floor that has no floor right above and at a place where there is a considerable distance from the equipment using fire.
As regards a generator room, the employer must conform to the requirements set forth in the following items:
事業者は、発生器室については、次に定めるところによらなければならない。
Article 303, paragraph (1), item (i)
to be constructed with an incombustible wall, and to have the following structure or a structure with the strength equivalent to or stronger than those listed in the following sub-items:
壁は、不燃性のものとし、次の構造又はこれと同等以上の強度を有する構造のものとすること。
Article 303, paragraph (1), item (i), (a)
to be made of ferroconcrete with the thickness of 4 cm or more; and
厚さ四センチメートル以上の鉄筋コンクリートとすること。
Article 303, paragraph (1), item (i), (b)
to be made of steel or lumber on which metal lath is lined and mortar is painted 3 cm or more in thickness, or of steel on which an iron plate with thickness of 1.5 mm or more are lined;
to use thin iron plate or lightweight incombustible materials for the roof and ceiling;
屋根及び天井には、薄鉄板又は軽い不燃性の材料を使用すること。
Article 303, paragraph (1), item (iii)
to project an exhaust pipe having a cross-section area of one-sixteenth of the floor area or more from the roof, and place the opening of the pipe at a distance of 1.5 m or more from a window, an entrance and other openings;
to use an iron plate with the thickness of 1.5 mm or more, or with a structure having the same strength as the iron plate or stronger using incombustible materials for the door of an entrance;
to keep the space between a wall and a generator that does not hinder the work of adjusting the generator, or the work of feeding of carbide, etc.
壁と発生器との間隔は、発生器の調整又はカーバイド送給等の作業を妨げない距離とすること。
Article 304第三百四条
Storeroom(格納室)
Article 304, paragraph (1)
As regards movable acetylene welding equipment, notwithstanding the provisions of Article 302, paragraph (1), the employer must store the equipment in a dedicated storeroom when it is not used; provided, however, that this does not apply when storing the equipment after its gas bell is removed and the generator is washed.
As regards the storeroom referred to in the preceding paragraph, the employer must construct it by using fire-proof materials such as iron plate-lined lumber and slate-lined lumber.
事業者は、前項の格納室については、木骨鉄板張、木骨スレート張等耐火性の構造としなければならない。
Article 305第三百五条
Standards of Acetylene Welding Equipment(アセチレン溶接装置の構造規格)
Article 305, paragraph (1)
As regards acetylene welding equipment (excluding generators and safety equipment) that generate or use acetylene of a gauge pressure (hereinafter referred to as "pressure" in this Article) of 7 kPa or more, the employer must conform to the requirements set forth in the following items:
the gas holder conforms to the following requirements:
ガスだめは、次に定めるところによるものであること。
Article 305, paragraph (1), item (i), (a)
the main parts to be made of steel plates or steel pipes with a thickness equal to or more than that listed in the right column of the following table in accordance with the inner diameter listed in the left column of the same table;
the method of joining steel plates or steel pipes of the main parts to be welding, or using rivet joints or bolt joints; and
主要部分の鋼板又は鋼管の接合方法は、溶接、びよう接又はボルト締めによるものであること。
Article 305, paragraph (1), item (i), (c)
to be equipped with a gas escape valve or a cock to discharge a mixed gas of acetylene and air;
アセチレンと空気との混合ガスを排出するためのガス逃がし弁又はコツクを備えていること。
Article 305, paragraph (1), item (ii)
for the gas holder for acetylene that is compressed by a compressor after being fed from the generator, in addition to compliance with the requirements set forth in the preceding item, to be equipped with a safety valve and a pressure gauge as prescribed in the following sub-items:
being one that operates before the pressure inside the gas holder reaches 140 kPa and closes by the time the pressure falls by 10 kPa from the normal working pressure;
having a dial with a diameter of 75 mm or more for a gauge attached to a stationary gas holder, and 50 mm or more for a gauge attached to a portable gas holder;
having a conspicuous indication on the scale at the position indicating the normal working pressure;
目もりには、常用圧力を示す位置に見やすい表示がされているものであること。
Article 305, paragraph (1), item (iii)
for the parts of the gas holder, purifiers, acetylene distributing lines, etc., which contact acetylene, copper or an alloy containing 70% or more copper are not used.
The employer must not use copper for the parts of the purifiers, acetylene distributing lines etc., of acetylene welding equipment other than those set forth in the preceding paragraph that is likely to come in contact with acetylene.
As regards acetylene welding equipment, the employer must provide safety equipment for each blowpipe; provided, however, that this does not apply when safety equipment is provided to the main pipe and for each branch pipe nearest to the blowpipes.
As regards acetylene welding equipment in which the gas holder and the generator are separated, the employer must provide safety equipment between the generator and the gas holder.
The employer must install a sludge pit at a safe place and its structure must conform to the requirements set forth in the following items; provided, however, that this does not apply to mobile acetylene welding equipment used for outwork:
the capacity of the sludge pit is to be three times or more of the carbide charging device.
容積は、カーバイドてん充器の三倍以上とすること。
Subsection 2 Gas Welding Equipment Using Manifolds第二款 ガス集合溶接装置
Article 308第三百八条
Installation of Gas Manifolds(ガス集合装置の設置)
Article 308, paragraph (1)
As regards a gas manifold set forth in Article 1, item (ii) of the Order (hereinafter referred to as "gas manifolds"), the employer must install them in a place at a distance of 5 m or more from equipment using fire.
As regards a gas manifolds other than those movable, the employer must install them in a dedicated room (hereinafter referred to as "gas manifold room").
As regards the space between the wall of the gas manifold room and a gas manifold, the employer must keep sufficient space for handling of the device, exchanging of a gas cylinder, etc.
As regards a gas manifold room, the employer must conform to the following requirements:
事業者は、ガス装置室については、次に定めるところに適合するものとしなければならない。
Article 309, paragraph (1), item (i)
the gas does not stagnate when there is leakage of gas;
ガスが漏えいしたときに、当該ガスが滞留しないこと。
Article 309, paragraph (1), item (ii)
to be constructed with a roof and a ceiling made of lightweight and incombustible materials; and
屋根及び天井の材料が軽い不燃性の物であること。
Article 309, paragraph (1), item (iii)
to be constructed with a wall made of incombustible materials.
壁の材料が不燃性の物であること。
Article 310第三百十条
Piping of Gas Welding Equipment using Manifolds(ガス集合溶接装置の配管)
Article 310, paragraph (1)
As regards the piping of the gas welding equipment using manifolds listed in Article 1, item (ii) of the Order (hereinafter referred to as "the gas welding equipment using manifolds"), the employer must conform to the requirements set forth in the following items:
for the joining part of a flange, a valve, a cock, etc., to take measures such as using gaskets and bringing the joining surfaces into close contact with each other; and
The employer must not use copper or an alloy containing 70% or more copper for the piping of the gas welding equipment using manifolds for dissolved acetylene and its accessories.
Management of Acetylene Welding Equipment(アセチレン溶接装置の管理等)
Article 312, paragraph (1)
When carrying out the work of welding, fusing or heating metals using acetylene welding equipment, the employer must comply with the requirements set forth in the following items:
to display the type, model, manufacturer's name, calculated quantity of hourly average gas generation, and the quantity of carbide fed in one lot of generators (excluding the gas generators of portable acetylene welding equipment) at a readily visible location in the generator room;
to prohibit persons other than the staff in charge from entering the generator room without reason by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that the generator room is subject to the prohibition of entry;
in a place within 5 m of the generator or within 3 m of the generator room, to prohibit smoking, the use of fire or acts that are liable to produce sparks by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that smoking, the use of fire or acts that are liable to produce sparks are prohibited at that place;
to take measures to prevent confusion between supply lines for oxygen from those for acetylene;
導管には、酸素用とアセチレン用との混同を防ぐための措置を講ずること。
Article 312, paragraph (1), item (v)
to provide appropriate fire extinguishing equipment at places where acetylene welding equipment is installed;
アセチレン溶接装置の設置場所には、適当な消火設備を備えること。
Article 312, paragraph (1), item (vi)
to not install the generators for portable acetylene welding equipment at places where the temperature is high, ventilation or airing is insufficient, or where there is much vibration, etc.; and
to have the person engaging in the work wear eye protector and protective gloves.
当該作業を行う者に保護眼鏡及び保護手袋を着用させること。
Article 313第三百十三条
Management of the Gas Welding Equipment using Manifolds(ガス集合溶接装置の管理等)
Article 313, paragraph (1)
When carrying out the work of welding, fusing or heating metal using the gas welding equipment using manifolds, the employer must comply with the requirements set forth in the following items:
to display the name of the gas used and the maximum quantity of gas stored at a readily visible location in the gas manifold room;
使用するガスの名称及び最大ガス貯蔵量を、ガス装置室の見やすい箇所に掲示すること。
Article 313, paragraph (1), item (ii)
to have the operations supervisor of gas welding attend when exchanging a gas cylinder;
ガスの容器を取り替えるときは、ガス溶接作業主任者に立ち合わせること。
Article 313, paragraph (1), item (iii)
to prohibit persons other than the staff in charge from entering the gas manifold room without reason by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that the gas manifold room is subject to the prohibition of entry;
in a place within 5 m of the gas manifolds, to prohibit smoking, the use of fire or acts that are liable to produce sparks by indicating the prohibition in a conspicuous place or by other methods, and, where the prohibition is made by a method other than indication, to indicate in a conspicuous place that smoking, the use of fire or acts that are liable to produce sparks are prohibited at that place;
to display the guidelines of operation and of inspection of a valve, a cock, etc., at a readily visible location in the gas manifold room;
バルブ、コック等の操作要領及び点検要領をガス装置室の見やすい箇所に表示すること。
Article 313, paragraph (1), item (vi)
to take measures to prevent confusion between supply lines for oxygen from those for gas;
導管には、酸素用とガス用との混同を防止するための措置を講ずること。
Article 313, paragraph (1), item (vii)
to install appropriate fire extinguishing equipment at the places where a gas manifold is installed; and
ガス集合装置の設置場所に適当な消火設備を設けること。
Article 313, paragraph (1), item (viii)
to have the person engaging in the work wear eye protector and protective gloves.
当該作業を行う者に保護眼鏡及び保護手袋を着用させること。
Copy link
Coming into force施行
The day a law or an amendment starts to apply. It is often months or years after promulgation, so that people have time to prepare. The Ministry of Justice's English usually says a law "comes into force" or "comes into effect", and sometimes calls the day its "enforcement date". Its "enforcement" more often means the word's other sense, carrying a law out, as in an Order for Enforcement (施行令), the Cabinet Order (政令) that sets out the details for carrying out an Act.
The Ministry of Justice's English of this passage has a slip, so the English shown is this site's correction of it. The Ministry printed:
As regards movable acetylene welding equipment, notwithstanding the provisions of Article 302, item (i), the employer must store the equipment in a dedicated storeroom when it is not used; provided, however, that this does not apply when storing the equipment after its gas bell is removed and the generator is washed.
Japanese Law Translation, Ministry of Justice
Translates the law as amended by Order of the Ministry of Health, Labour and Welfare No. 185 of 2006 (平成十八年厚生労働省令第百八十五号)
The Ministry of Justice's English of this passage has a slip, so the English shown is this site's correction of it. The Ministry printed:
As regards acetylene welding equipment (excluding generators and safety equipment) that generate or use acetylene of a gauge pressure (hereinafter referred to as "pressure" in this Article) of 7 kPa or more, the employer must conform to the requiremenst set forth in the following items:
Japanese Law Translation, Ministry of Justice
Translates the law as amended by Order of the Ministry of Health, Labour and Welfare No. 185 of 2006 (平成十八年厚生労働省令第百八十五号)
The Ministry of Justice's English of this passage has a slip, so the English shown is this site's correction of it. The Ministry printed:
The employer must install a sludge pit at a safe place and its structure must conform to the requiremetns set forth in the following items; provided, however, that this does not apply to mobile acetylene welding equipment used for outwork:
Japanese Law Translation, Ministry of Justice
Translates the law as amended by Order of the Ministry of Health, Labour and Welfare No. 185 of 2006 (平成十八年厚生労働省令第百八十五号)