Search

Search provisions, jump to a law or an article

This text is not in force yetIt on 1 April 2027, in 4 months

Read the text in force →

Ordinance on Industrial Safety and Health

労働安全衛生規則(ろうどうあんぜんえいせいきそく)

Chapter II Construction Machines (Articles 195 to 220)

The law as Ministerial Order Partially Amending the Safety Ordinance for Cranes and the Ordinance on Industrial Safety and Health (Ministry of Health, Labour and Welfare Order No. 90 of 2026) leaves it, with the words it changes marked.

The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.

How the changes are shown

Underlined: words the amendment adds. A bar: where it removes words.Underlined: words the amendment adds. Struck through: the words it removes.Underlined: words the amendment adds. Struck through: the words it removes.

Section 3 Railway Equipment and Handcart第三節 軌道装置及び手押し車両

Subsection 1 General Provisions第一款 総則

Article 195第百九十五条

Definitions(定義)
Article 195, paragraph (1)

The term "railway equipment" as used in this Ministerial Order means all units of equipment including rail tracks and a vehicle attached to a workplace, a power vehicle, a winch, etc. that is driven with the power on rails and used for transporting workers or cargos (excluding those for which the Railway Operation Act (Act No. 65 of 1900), the Railway Business Act (Act No. 92 of 1986) or the Railway Act (Act No. 76 of 1921) applies).

この省令で軌道装置とは、事業場附帯の軌道及び車両、動力車、巻上げ機等を含む一切の装置で、動力を用いて軌条により労働者又は荷物を運搬する用に供されるもの(鉄道営業法(明治三十三年法律第六十五号)、鉄道事業法(昭和六十一年法律第九十二号)又は軌道法(大正十年法律第七十六号)の適用を受けるものを除く。)をいう。

Subsection 2 Rail Tracks第二款 軌道等

Article 196第百九十六条

Weights of Rails(軌条の重量)
Article 196, paragraph (1)

The employer must have the weight of a rail to be equal to or more than the weight listed in the right column of the following Table in accordance with the vehicle body weight listed in the left column of the same Table:

Vehicle Body WeightWeight of Rail
Less than 5 tons9 kg
5 tons or more and less than 10 tons12 kg
10 tons or more and less than 15 tons15 kg
15 tons or more22 kg

事業者は、軌条の重量については、次の表の上欄に掲げる車両重量に応じて、同表の下欄に掲げる軌条重量以上としなければならない。

車両重量軌条重量
五トン未満九キログラム
五トン以上十トン未満十二キログラム
十トン以上十五トン未満十五キログラム
十五トン以上二十二キログラム

Article 197第百九十七条

Joint of Rails(軌条の継目)
Article 197, paragraph (1)

As regards joint of rails, the employer must securely fix the rails by using joint plates and welding them.

事業者は、軌条の継目については、継目板を用い、溶接を行なう等により堅固に固定しなければならない。

Article 198第百九十八条

Laying Rails(軌条の敷設)
Article 198, paragraph (1)

As regards laying of rails, the employer must securely fix the rails on the sleeper, concrete bed, etc., by using rail spikes, metal fixture, etc.

事業者は、軌条の敷設については、犬くぎ、止め金具等を用いて、軌条をまくら木、コンクリート道床等に堅固に締結しなければならない。

Article 199第百九十九条

Sleeper(まくら木)
Article 199, paragraph (1)

The employer must ensure that the size and intervals of sleepers are appropriate to the vehicle body weight, the condition of bed, etc., in order to stabilize the rails.

事業者は、まくら木の大きさ及び配置の間隔については、軌条を安定させるため、車両重量、道床の状態等に応じたものとしなければならない。

Article 199, paragraph (2)

As regards the sleeper to be used at places where they are susceptible to corrosion or where they are difficult to replace, the employer must ensure that sleepers having sufficient durability are used.

事業者は、腐食しやすい箇所又は取替えの困難な箇所で用いるまくら木については、耐久性を有するものとしなければならない。

Article 200第二百条

Bed(道床)
Article 200, paragraph (1)

As regards rail tracks of which the bed consists of crushed stones, gravel, etc., among rail tracks laid for operating power vehicle with the vehicle body weight of 5 tons or more, the employer must sufficiently harden the bed as well as take measures to have good drainage in order to maintain the sleeper and rails in a safe condition.

事業者は、車両重量五トン以上の動力車を運転する軌道のうち道床が砕石、砂利等で形成されているものについては、まくら木及び軌条を安全に保持するため、道床を十分つき固め、かつ、排水を良好にするための措置を講じなければならない。

Article 201第二百一条

Curved Section(曲線部)
Article 201, paragraph (1)

The employer must conform to the requirement set forth in the following items for a curved section of rail tracks:

事業者は、軌道の曲線部については、次に定めるところによらなければならない。

Article 201, paragraph (1), item (i)

to have the radius of a curvature of 10 m or more;

曲線半径は、十メートル以上とすること。

Article 201, paragraph (1), item (ii)

to maintain an appropriate cant and a slack; and

適当なカント及びスラツクを保つこと。

Article 201, paragraph (1), item (iii)

to provide a guard rail in accordance with the radius of the curvature.

曲線半径に応じ、護輪軌条を設けること。

Article 202第二百二条

Gradient of Rail Tracks(軌道のこう配)
Article 202, paragraph (1)

As regards the gradient of rail tracks at the section where a power vehicle is used, the employer must set the gradient ratio to fifty thousandth or less.

事業者は、動力車を使用する区間の軌道のこう配については、千分の五十以下としなければならない。

Article 203第二百三条

Junction of Rail Tracks(軌道の分岐点等)
Article 203, paragraph (1)

The employer must equip the junction of rail tracks with a point and a frog having secure function, and equip the end of the rail tracks with secure wheel stoppers.

事業者は、軌道の分岐する部分には、確実な機能を有する転てつ器及びてつさを設け、軌道の終端には、確実な車止め装置を設けなければならない。

Article 204第二百四条

Anchoring Device(逸走防止装置)
Article 204, paragraph (1)

When there is a risk of a vehicle overrunning, the employer must install an anchoring device.

事業者は、車両が逸走するおそれのあるときは、逸走防止装置を設けなければならない。

Article 205第二百五条

Clearance Between Vehicle and Side Wall(車両と側壁等との間隔)
Article 205, paragraph (1)

When installing railway equipment inside a tunnel, etc. under construction, the employer must provide a clearance of 0.6 m or more between a vehicle and the side wall or an obstacle on one side of the track in order to prevent the danger of vehicles in operation coming into contact with persons engaged in work who are passing through; provided, however, that this does not apply when providing the clearance of 0.6 m or more is difficult due to reasons such as the small sectional area of the tunnel, etc., and any of the following measures has been taken:

事業者は、建設中のずい道等の内部に軌道装置を設けるときは、通行する作業従事者に運行する車両が接触する危険を防止するため、その片側において、当該車両と側壁又は障害物との間隔を〇・六メートル以上としなければならない。ただし、ずい道等の断面が狭小であること等により当該間隔を〇・六メートル以上とすることが困難な場合で、次のいずれかの措置を講じたときは、この限りでない。

Article 205, paragraph (1), item (i)

to provide a clearly discernible safety zones at appropriate intervals; and

明確に識別できる回避所を適当な間隔で設けること。

Article 205, paragraph (1), item (ii)

to not allow persons engaged in work to enter the area in the traveling direction of a vehicle in operation by installing a signaling device, arranging a watcher, etc.

信号装置の設置、監視人の配置等により運行中の車両の進行方向上に作業従事者を立ち入らせないこと。

Article 206第二百六条

Preventive Measures for a Person Riding on a Vehicle from Coming into Contact(車両とう乗者の接触予防措置)
Article 206, paragraph (1)

When installing railway equipment inside a tunnel, etc., under construction, the employer must maintain necessary distance between a vehicle and the sidewall or the ceiling of the tunnel, etc., and obstacles in order to prevent the person riding on a vehicle from coming into contact with the sidewall or the ceiling of the tunnel, etc., or obstacles; provided, however, that this does not apply when obstacles such as shoring, etc., deformed by the load of the land exist, and measures for easily discerning the obstacles have been taken in order to prevent the dangers of person riding on a vehicle from coming into contact with the obstacles in the tunnel, etc.

事業者は、建設中のずい道等の内部に軌道装置を設けるときは、車両のとう乗者がずい道等の内部の側壁、天盤、障害物等に接触する危険を防止するため、当該車両と当該側壁、天盤、障害物等との間に必要な距離を保持しなければならない。ただし、地山の荷重により変形した支保工等障害物があるときに、当該車両のとう乗者が当該障害物に接触する危険を防止するため、車両とう乗者が容易に識別できる措置を講じたときには、この限りでない。

Article 207第二百七条

Signaling Device(信号装置)
Article 207, paragraph (1)

The employer must install a signaling device in accordance with the condition of railway equipment.

事業者は、軌道装置の状況に応じて信号装置を設けなければならない。

Subsection 3 Vehicle第三款 車両

Article 208第二百八条

Brake of a Power Vehicle(動力車のブレーキ)
Article 208, paragraph (1)

The employer must equip a power vehicle with a hand brake as well as equip a power vehicle that has the vehicle body weight of 10 tons or more with a power brake.

事業者は、動力車には、手用ブレーキを備え、かつ、十トン以上の動力車には、動力ブレーキをあわせ備えなければならない。

Article 208, paragraph (2)

The employer must set the ratio of the pressure of a brake applied to the brake shoe to the pressure of the brake wheel applied to rails to fifty hundredth or more and seventy-five hundredth or less for a power brake and twenty hundredth or more for a hand brake.

事業者は、ブレーキの制輪子に作用する圧力と制動車輪の軌条に対する圧力との割合を、動力ブレーキにあつては百分の五十以上百分の七十五以下、手用ブレーキにあつては百分の二十以上としなければならない。

Article 209第二百九条

Facilities for a Power Vehicle(動力車の設備)
Article 209, paragraph (1)

The employer must not use a power vehicle unless it conforms to the following requirements:

事業者は、動力車については、次に定めるところに適合するものでなければ、使用してはならない。

Article 209, paragraph (1), item (i)

to be equipped with signaling device such as a whistle, an alarm bell, etc.;

汽笛、警鈴等の合図の装置を備えること。

Article 209, paragraph (1), item (ii)

to be equipped with a front lamp and lighting facilities for the driver's cabin when operating the power vehicle at night or underground;

夜間又は地下において使用するときは、前照灯及び運転室の照明設備を設けること。

Article 209, paragraph (1), item (iii)

to be equipped with a lubricant pressure indicator for an internal combustion locomotive; and

内燃機関車には、潤滑油の圧力を表示する計器を備えること。

Article 209, paragraph (1), item (iv)

to be equipped with an automatic circuit-breaker for an electric locomotive, and with a lightning arrester for an electric locomotive with an aerial cableway system.

電気機関車には、自動しや断器を備え、かつ、架空線式の場合には避雷器を備えること。

Article 210第二百十条

Operator's Seat of a Power Vehicle(動力車の運転者席)
Article 210, paragraph (1)

The employer must not use an operator's seat of a power vehicle unless it conforms to the following requirements:

事業者は、動力車の運転者席については、次に定めるところに適合するものでなければ、使用してはならない。

Article 210, paragraph (1), item (i)

to have the structure that has a visibility that enables an operator to safely operate the vehicle; and

運転者が安全な運転を行なうことができる視界を有する構造とすること。

Article 210, paragraph (1), item (ii)

to be equipped with an enclosure, etc., in order to prevent an operator from dangers of falling.

運転者の転落による危険を防止するため、囲い等を設けること。

Article 211第二百十一条

Worker Carrier(人車)
Article 211, paragraph (1)

The employer must not use a vehicle exclusively for transporting workers (hereinafter referred to as "worker carrier") unless it conforms to the following requirements:

事業者は、労働者の輸送に用いる専用の車両(以下「人車」という。)については、次に定めるところに適合するものでなければ、使用してはならない。

Article 211, paragraph (1), item (i)

to be equipped with such devices as a seat, a grasping rod, etc. that enables workers to ride on the carrier safely;

労働者が安全に乗車できる座席、握り棒等の設備を設けること。

Article 211, paragraph (1), item (ii)

to be equipped with an enclosure and a gate;

囲い及び乗降口を設けること。

Article 211, paragraph (1), item (iii)

as regards a worker carrier pulled by a winching system used on inclined rails, to be equipped with facilities enabling an operator of the winch and a person riding on the worker carrier to communicate with each other in an emergency;

斜道において用いる巻上げ装置によりけん引される人車については、巻上げ機の運転者と人車のとう乗者とが緊急時に連絡できる設備を設けること。

Article 211, paragraph (1), item (iv)

as regards the worker carrier set forth in the preceding item, to be equipped with an emergency stop device in order to prevent dangers due to cutting off of a wire rope, excessive speed, etc.; and

前号の人車については、ワイヤロープの切断、速度超過等による危険を防止するため、非常停止装置を設けること。

Article 211, paragraph (1), item (v)

as regards a worker carrier used on inclined rails with an inclined angle of 30 degrees or more, to be equipped with a derailment preventive device.

傾斜角三十度以上の斜道に用いる人車については、脱線予防装置を設けること。

Article 212第二百十二条

Wheels(車輪)
Article 212, paragraph (1)

The employer must not use a wheel unless it conforms to the following requirements:

事業者は、車輪については、次に定めるところに適合するものでなければ、使用してはならない。

Article 212, paragraph (1), item (i)

to have the width which ensures that the tread safely mounts on the rails when the tires with their flanges worn to the maximum extent pass the track part having the maximum gauge;

タイヤの幅は、フランジが最も摩耗した状態で、最大軌間を通過するときに、なおその踏面が軌条に安全に乗る広さとすること。

Article 212, paragraph (1), item (ii)

to have a flange thickness which provides sufficient strength even when their flange has been worn to the maximum extent and while allowing the tires to pass through junctions and frogs; and

フランジの厚さは、最も摩耗したときに、十分な強さを有し、かつ、分岐及びてつさの通過に差しつかえない厚さ以下とすること。

Article 212, paragraph (1), item (iii)

to have a flange height which is higher than that required for preventing tires from derailment and which does not run on the joint plates, frogs, etc.

フランジの高さは、タイヤが軌条からはずれない高さ以上で、継目板及びてつさ等に乗り上げない高さとすること。

Article 213第二百十三条

Coupling Device(連結装置)
Article 213, paragraph (1)

When coupling vehicles, the employer must use a secure coupling device.

事業者は、車両を連結するときは、確実な連結装置を用いなければならない。

Article 214第二百十四条

Coupling of Worker Carriers on Inclined Rails(斜道における人車の連結)
Article 214, paragraph (1)

When using a worker carrier on inclined rails and coupling a worker carrier with another worker carrier or with a wire rope socket by a chain or a link, the employer must keep them coupled with a spare chain or wire rope in order to prevent the worker carrier from breaking into a run due to cutting off of the chain or the link.

事業者は、斜道において人車を用いる場合において、人車と人車又はワイヤロープソケツトをチエーン又はリンクで連結するときは、当該チエーン又はリンクの切断等による人車の逸走を防止するため、予備のチエーン又はワイヤロープで連結しておかなければならない。

Subsection 4 Winching System第四款 巻上げ装置

Article 215第二百十五条

Brake of a Winching System(巻上げ装置のブレーキ)
Article 215, paragraph (1)

The employer must equip a winching system with a brake that enables to promptly stop a vehicle when the vehicle is applied the maximum load, and maintain the stopped state of the vehicle.

事業者は、巻上げ装置には、車両に最大の荷重をかけた場合において、車両をすみやかに停止させ、かつ、その停止状態を保持することができるブレーキを備えなければならない。

Article 216第二百十六条

Wire Rope(ワイヤロープ)
Article 216, paragraph (1)

The employer must not use a wire rope to be used on a winching system unless it conforms to the following requirements:

事業者は、巻上げ装置に用いるワイヤロープについては、次に定めるところに適合するものでなければ、使用してはならない。

Article 216, paragraph (1), item (i)

to have the safety coefficient of a wire rope at 6 or higher (10 or more for a wire rope to be used for a worker carrier). In this case, the safety coefficient is to be the value obtained by dividing the value of the breaking load of the wire rope by the maximum value of the load applied to the wire rope; and

安全係数は六以上(人車に用いるワイヤロープにあつては、十以上)とすること。この場合の安全係数は、ワイヤロープの切断荷重の値を当該ワイヤロープにかかる荷重の最大の値で除した値とする。

Article 216, paragraph (1), item (ii)

to be fixed to vehicles by secure method such as using links.

リンクを使用する等確実な方法により、車両に取り付けること。

Article 217第二百十七条

Prohibition of the Use of an Inadequate Wire Rope(不適格なワイヤロープの使用禁止)
Article 217, paragraph (1)

The employer must not use a wire rope falling under any of the following items for a winching system:

事業者は、次のいずれかに該当するワイヤロープを巻上げ装置の巻上げ用ワイヤロープとして使用してはならない。

Article 217, paragraph (1), item (i)

those with 10% or more of element wires cut in one strand;

ワイヤロープ一よりの間において素線の数の十パーセント以上の素線が切断しているもの

Article 217, paragraph (1), item (ii)

those with the reduction ratio of a diameter exceeding 7% of the nominal diameter;

直径の減少が公称径の七パーセントを超えるもの

Article 217, paragraph (1), item (iii)

those with kinks; and

キンクしたもの

Article 217, paragraph (1), item (iv)

those with marked deformation or corrosion.

著しい形くずれ又は腐食があるもの

Article 218第二百十八条

Depth Indicator(深度指示器)
Article 218, paragraph (1)

When using worker carrier on an inclined pit line and it is difficult for the operator of the winch to confirm the position of the worker carrier, the employer must equip the winch with a depth indicator that enables the operator to readily confirm the position of the worker carrier.

事業者は、斜坑において人車を用いる場合において、巻上げ機の運転者が人車の位置を確認することが困難なときは、当該運転者が容易に確認できる深度指示器を備えなければならない。

Subsection 5 Prevention of Dangers Pertaining to the Use of the Railway Equipment第五款 軌道装置の使用に係る危険の防止

Article 219第二百十九条

Display Method of a Signaling Device(信号装置の表示方法)
Article 219, paragraph (1)

When having installed a signaling device, the employer must establish in advance the display method for the signaling device, and make the display method known to the workers concerned.

事業者は、信号装置を設けたときは、あらかじめ、当該信号装置の表示方法を定め、かつ、関係労働者に周知させなければならない。

Article 220第二百二十条

Signals(合図)
Article 220, paragraph (1)

As regards the operation of the railway equipment, the employer must establish in advance a signaling method for the operation and make the signaling method known to the workers concerned.

事業者は、軌道装置の運転については、あらかじめ、当該運転に関する合図方法を定め、かつ、これを関係労働者に周知させなければならない。

Article 220, paragraph (2)

The operator of the railway equipment set forth in the preceding paragraph must operate the railway equipment according to the signaling method set forth in the same paragraph.

前項の軌道装置の運転者は、同項の合図方法により運転しなければならない。

© 2026 japanlaw.orgA copy for reading and reference — not an official source, and not legal advice. Only the Japanese text published by the government has legal effect.Run by Genjido LLC (源氏道合同会社) · contact@genjido.comContactSourcesTermsPrivacy