Chapter II Construction Machines (Articles 194-14 to 194-28)
The law as Ministerial Order Partially Amending the Ordinance on Industrial Safety and Health (Ministry of Health, Labour and Welfare Order No. 68 of 2026) leaves it, with the words it changes marked.
The main text is read a page at a time: a chapter to a page, and a long chapter in runs of articles. The whole main text, and the supplementary provisions and appended tables this amendment changes. Those it leaves untouched are on the page for the text in force.
Article 194-14第百九十四条の十四
Transfer of Vehicle for Work at Height(高所作業車の移送)
Article 194-14, paragraph (1)
When using a loading plate, fills, etc., in the case where a vehicle for work at height is loaded to a truck, etc., or unloaded from a truck, etc., by self-propelling or towing for transferring the machine, the employer must comply with the following requirements in order to prevent dangers due to overturning, falling, etc., of the vehicle:
when using fills or a temporary stand, etc., to secure sufficient width, strength and appropriate incline.
盛土、仮設台等を使用するときは、十分な幅及び強度並びに適当なこう配を確保すること。
Article 194-15第百九十四条の十五
Restriction of Riding(搭乗の制限)
Article 194-15, paragraph (1)
When the work using a vehicle for work at height is carried out, the employer must not have a person engaged in work at the workshop ride in any place other than the riding seat or the working floor.
As regards a vehicle for work at height, the employer must not use it for the load exceeding the loading capacity (meaning the maximum load the vehicle is capable of raising with personnel or loads on working floor, in accordance with its structure and materials of the vehicle for work at height) and for other purposes exceeding its capabilities.
Restriction on the Use for Purposes Other than the Main Purpose(主たる用途以外の使用の制限)
Article 194-17, paragraph (1)
The employer must not use a vehicle for work at height for purposes other than its main purpose, such as hoisting loads; provided, however, that this does not apply when there is no risk of endangering workers in doing so.
When carrying out the work of repairing a vehicle for work at height, or fitting or removing the working floor, the employer must designate a person to supervise the work and have the person carry out the following matters:
to decide the work procedures, and directly supervise the work; and
作業手順を決定し、作業を直接指揮すること。
Article 194-18, paragraph (1), item (ii)
to monitor the use of the safety prop, safety block, etc., prescribed in paragraph (1) of the following Article.
次条第一項に規定する安全支柱、安全ブロック等の使用状況を監視すること。
Article 194-19第百九十四条の十九
Prevention of Danger Due to Falling Booms(ブーム等の降下による危険の防止)
Article 194-19, paragraph (1)
When carrying out the work of repairs, inspection, etc., below the raised boom of a vehicle for work at height, the employer must have the worker engaging in the work use a safety prop and a safety block, etc., in order to prevent workers from dangers due to the unexpected falling of the boom, etc.
The worker engaging in the work set forth in the preceding paragraph must use the safety prop and safety block, etc., set forth in the same paragraph.
前項の作業に従事する労働者は、同項の安全支柱、安全ブロック等を使用しなければならない。
Article 194-20第百九十四条の二十
Restriction of Riding on the Working Floor(作業床への搭乗制限等)
Article 194-20, paragraph (1)
When having a vehicle for work at height (excluding those with a structure of carrying out the traveling operation on the working floor; hereinafter the same applies in this Article) travel in a workshop where workers carry out work, the employer must not allow a person engaged in work to ride on the working floor of the vehicle for work at height; provided, however, that this does not apply when having the vehicle for work at height travel at a level and firm place, and the following measures have been taken:
to arrange a guide, and have the person guide the vehicle for work at height;
誘導者を配置し、その者に高所作業車を誘導させること。
Article 194-20, paragraph (1), item (ii)
to set fixed signals and have the guide set forth in the preceding item give the signals;
一定の合図を定め、前号の誘導者に当該合図を行わせること。
Article 194-20, paragraph (1), item (iii)
to set an appropriate working speed limit for the vehicle for work at height in accordance with the height of the working floor and the length of the boom, etc. of the vehicle for work at height in advance, and have the operator operate the vehicle within the speed limit.
A person engaged in work, excluding the case referred to in the proviso of the preceding paragraph, must not ride on the working floor of a vehicle for work at height while it is traveling.
作業従事者は、前項ただし書の場合を除き、走行中の高所作業車の作業床に乗つてはならない。
Article 194-20, paragraph (3)
The operator of the vehicle for work at height set forth in the proviso of paragraph (1) must follow the instructions given by the guide set forth in item (i) of the same paragraph and the signals set forth in item (ii) of the same paragraph, and must not operate the vehicle for work at height at a speed exceeding the speed limit set forth in item (iii) of the same paragraph.
When traveling a vehicle for work at height with a structure of carrying out the traveling operation on a working floor at places other than level and firm places, the employer must take the following measures:
to take the measures listed in paragraph (1), items (i) and (ii) of the preceding Article; and
前条第一項第一号及び第二号に掲げる措置を講ずること。
Article 194-21, paragraph (1), item (ii)
to establish in advance, an appropriate working speed limit for the vehicle for work at height in accordance with the height of the working floor and the length of the boom of the vehicle for work at height, and the landform and condition of the ground pertaining to the work, and have the operator operate the vehicle within the speed limit.
The provisions of paragraph (3) of the preceding Article apply mutatis mutandis to the operator of the vehicle for work at height set forth in the preceding paragraph. In this case, the term "item (iii) of the same paragraph" in paragraph (3) of the same Article is deemed to be replaced with "paragraph (1), item (ii) of the following Article."
Use of Fall Arrest Equipment with the Required Performance, etc.(要求性能墜落制止用器具等の使用)
Article 194-22, paragraph (1)
When the work using a vehicle for work at height (excluding those with the structure in which the working floor rises or lowers only in the direction perpendicular to the ground plane) is carried out, the employer must have the workers on the working floor of the vehicle for work at height use fall arrest equipment with the required performance, etc.
The worker set forth in the preceding paragraph must use fall arrest equipment with the required performance, etc.
前項の労働者は、要求性能墜落制止用器具等を使用しなければならない。
Article 194-23第百九十四条の二十三
Periodical Self-inspection(定期自主検査)
Article 194-23, paragraph (1)
As regards a vehicle for work at height, the employer must carry out a self-inspection for the following matters periodically once every period not exceeding one year; provided, however, that this does not apply to the non-use period of a vehicle for work at height which is not used for a period exceeding one year:
abnormalities in the compression pressure, valve clearance and other abnormalities of the prime mover;
圧縮圧力、弁すき間その他原動機の異常の有無
Article 194-23, paragraph (1), item (ii)
abnormalities in the clutch, transmission, propeller shaft, differential and other abnormalities of power transmission devices;
クラッチ、トランスミッション、プロペラシャフト、デファレンシャルその他動力伝達装置の異常の有無
Article 194-23, paragraph (1), item (iii)
abnormalities in the drive wheel, idling wheel, vertical trunk roller, belt, tire, wheel bearing and other abnormalities of traveling devices;
起動輪、遊動輪、上下転輪、履帯、タイヤ、ホイールベアリングその他走行装置の異常の有無
Article 194-23, paragraph (1), item (iv)
abnormalities in the rotation angle of left and right steering wheels, knuckle, rod, arm and other abnormalities of controlling devices;
かじ取り車輪の左右の回転角度、ナックル、ロッド、アームその他操縦装置の異常の有無
Article 194-23, paragraph (1), item (v)
abnormalities in braking capability, brake drum, brake shoe and other abnormalities of braking devices;
制動能力、ブレーキドラム、ブレーキシューその他制動装置の異常の有無
Article 194-23, paragraph (1), item (vi)
abnormalities in the boom, lifting and lowering device, bending device, balance device, working floor and other abnormalities of working devices;
ブーム、昇降装置、屈折装置、平衡装置、作業床その他作業装置の異常の有無
Article 194-23, paragraph (1), item (vii)
abnormalities in the hydraulic pump, hydraulic motor, cylinder, safety valve and other abnormalities of the hydraulic system.
油圧ポンプ、油圧モーター、シリンダー、安全弁その他油圧装置の異常の有無
Article 194-23, paragraph (1), item (viii)
abnormalities in voltage, amperage and other abnormalities of the electrical system; and
電圧、電流その他電気系統の異常の有無
Article 194-23, paragraph (1), item (ix)
abnormalities in the body, operating device, safety device, locking device, warning device, direction indicator, lighting device and meter.
車体、操作装置、安全装置、ロック装置、警報装置、方向指示器、灯火装置及び計器の異常の有無
Article 194-23, paragraph (2)
As regards the vehicle for work at height set forth in the proviso of the preceding paragraph, the employer must carry out self-inspection for the matters listed in each item of the same paragraph before resuming the operation.
The provisions of the preceding two paragraphs apply mutatis mutandis to the self-inspection pursuant to the provisions of Article 45, paragraph (2) of the Act. In this case, the term "employer" in these provisions is deemed to be replaced with "individual business operator."
As regards a vehicle for work at height, the employer must carry out a self-inspection for the following matters periodically once every period not exceeding one month; provided, however, that this does not apply to the non-use period of a vehicle for work at height which is not used for a period exceeding one month:
abnormalities in the braking device, clutch and steering system;
制動装置、クラッチ及び操作装置の異常の有無
Article 194-24, paragraph (1), item (ii)
abnormalities in the working device and hydraulic system; and
作業装置及び油圧装置の異常の有無
Article 194-24, paragraph (1), item (iii)
abnormalities in the safety device.
安全装置の異常の有無
Article 194-24, paragraph (2)
As regards the vehicle for work at height set forth in the proviso of the preceding paragraph, the employer must carry out a self-inspection for the matters listed in each item of the same paragraph before resuming the operation.
The provisions of the preceding two paragraphs apply mutatis mutandis to the self-inspection pursuant to the provisions of Article 45, paragraph (2) of the Act. In this case, the term "employer" in these provisions is deemed to be replaced with "individual business operator."
When having carried out the self-inspection set forth in Article 194-23, paragraph (1) or (2) or paragraph (1) or (2) of the preceding Article, the employer must record the following matters and preserve the record for three years:
the name of the person who carried out the inspection; and
検査を実施した者の氏名
Article 194-25, paragraph (1), item (vi)
when measures such as repairs have been taken based on the result of the inspection, the details of the repairs.
検査の結果に基づいて補修等の措置を講じたときは、その内容
Article 194-25, paragraph (2)
The provisions of the preceding paragraph apply mutatis mutandis to the self-inspection pursuant to the provisions of Article 45, paragraph (2) of the Act. In this case, the term "employer" in the preceding paragraph is deemed to be replaced with "individual business operator," and the term "Article 194-23, paragraph (1) or (2) or paragraph (1) or (2) of the preceding Article" is deemed to be replaced with "Article 194-23, paragraph (1) or (2) as applied mutatis mutandis pursuant to paragraph (3) of that Article, or paragraph (1) or (2) of the preceding Article as applied mutatis mutandis pursuant to paragraph (3) of that Article."
The specified inspection pertaining to the vehicle for work at height is to be the self-inspection prescribed in Article 194-23.
高所作業車に係る特定自主検査は、第百九十四条の二十三に規定する自主検査とする。
Article 194-26, paragraph (2)
The provisions of Article 151-24, paragraph (2) apply mutatis mutandis to a person who has the qualifications prescribed by the Order of the Ministry of Health, Labour and Welfare set forth in the items of Article 45, paragraph (3) of the Act pertaining to a vehicle for work at height. In this case, the term "forklift" in Article 151-24, paragraph (2), item (i) is deemed to be replaced with "vehicle for work at height."
As regards the vehicle for work at height (limited to those for which Article 48, paragraph (1) of the Road Transport Vehicle Act applies) used for operation, when the employer or individual business operator has carried out an inspection pursuant to the provisions of the same paragraph, they are not required to carry out the self-inspection set forth in Article 194-23, paragraphs (1) and (2) (including as applied mutatis mutandis pursuant to paragraph (3) of that Article) for the parts where the inspection has been carried out.
As regards the application of the provisions of paragraph (1) of the preceding Article (including as applied mutatis mutandis pursuant to paragraph (2) of that Article) when having a registered inspection agency conduct the specified inspection pertaining to a vehicle for work at height, the term "the name of the person who carried out the inspection" in paragraph (1), item (v) of the same Article is deemed to be replaced with "the name of the registered inspection agency."
When having carried out the self-inspection pertaining to a vehicle for work at height, the employer or individual business operator must affix an inspection sticker stating the month and year when the specified inspection was carried out at a readily visible part of the vehicle.
When the work by vehicle for work at height is carried out, the employer must inspect the functions of the braking device, controlling device and working device before commencing the work for the day.
When having found an abnormality in carrying out the self-inspection set forth in Article 194-23, paragraph (1) or (2) or Article 194-24, paragraph (1) or (2), or the inspection set forth in the preceding Article, the employer must immediately make repairs or take other necessary measures.
When having found an abnormality in carrying out the self-inspection set forth in Article 194-23, paragraph (1) or (2) as applied mutatis mutandis pursuant to paragraph (3) of that Article or Article 194-24, paragraph (1) or (2) as applied mutatis mutandis pursuant to paragraph (3) of that Article, the individual business operator is to immediately make repairs or take other necessary measures.
The day a law or an amendment starts to apply. It is often months or years after promulgation, so that people have time to prepare. The Ministry of Justice's English usually says a law "comes into force" or "comes into effect", and sometimes calls the day its "enforcement date". Its "enforcement" more often means the word's other sense, carrying a law out, as in an Order for Enforcement (施行令), the Cabinet Order (政令) that sets out the details for carrying out an Act.
Machine translation, corrected on review, not official
English translation
Written for this site with AI
Corrected by this site
The Ministry of Justice's English of this passage has a slip, so the English shown is this site's correction of it. The Ministry printed:
The employer must not use a vehicle for work at height for purposes other than its main purpose of hositing loads; provided, however, that this does not apply ther is no risk of endangering workers in doing so.
Japanese Law Translation, Ministry of Justice
Translates the law as amended by Order of the Ministry of Health, Labour and Welfare No. 185 of 2006 (平成十八年厚生労働省令第百八十五号)